Database Users

Help.. I can't turn on my htc

I installed Miri Topaz Keyboard from http://blog.celogeek.com/mobile/mob.../#cg_880601ece8119b663a92f2a39784b881cc20f2b2
And after installation phone request me to phone reset, i clicked OK and than i saw text "smart mobility" with some numberl which look like IP, but i think that was a version number (u know numbers were red). When blackstone should show logo windows, it shown black screen. After reset, and after put out and put in battery, SIM card and memory stick it is showing this same. Please Help.
It looks as if windows mobile is broken, but why? I just installed keyboard. Please help again ;/
WM 6.5 Miri Manila 2.5 v.13

Domin1992 said:
I installed Miri Topaz Keyboard from http://blog.celogeek.com/mobile/mob.../#cg_880601ece8119b663a92f2a39784b881cc20f2b2
And after installation phone request me to phone reset, i clicked OK and than i saw text "smart mobility" with some numberl which look like IP, but i think that was a version number (u know numbers were red). When blackstone should show logo windows, it shown black screen. After reset, and after put out and put in battery, SIM card and memory stick it is showing this same. Please Help.
It looks as if windows mobile is broken, but why? I just installed keyboard. Please help again ;/
WM 6.5 Miri Manila 2.5 v.13
Click to expand...
Click to collapse
Hi Domin1992,
as stated above, you have mentioned that you performed a reset - was this a soft reset only with your stylus?
If you are unable to power on your phone at all, then there may be a possibility that you have a hardware issue (could be a problem with the motherboard circuit or battery).
How do you charge your phone? Via the mains adapter, or the USB link?
Try connecting your phone via your external power source using your mains charger or via USB cable and leave it for 2-3 hours and see if it picks up. (also look on device for indication of it receiving power by the lit LED).
If you have a charged battery insert it and power on the phone. If your phone doesn't have a hardware damage it should start. If it powers on (with the phone powered on, regardless of what's been displayed), then try performing a hard reset - especially if you cannot load the Manilla interface then i think you should try doing this. Also note that by performing a hard reset, you will lose all data stored in your phones RAM (this excludes data stored on your MicroSD card)
Regards.

After installation, device was doing reset after I clicked OK when device request me to do it.
When my device didn't want to load windows logo, I take out battery (device don't working without battery during is pluging to external power source) and I used stylus to reset.
I used to charge my device via mains adapter. You know it is USB link plugged to small box which is going to socket.
Today morning I pluged my device to external power source, and want to power on. After 10 minutes there is text.
"The device is unable to boot because either you have tourned off the device incorrectly or tried to install an application from untrusted source. Press Volume Up to rest your device or press your other button to cancel. This operation will delete all your personal data and restore the device to it's factory default settings."
Ok thats great, but i try to press Volume Up and I haven't reaction.
No one button isn't working.
I have to press this button once, 5sec or 10sec?

This is a hard reset. You should pres the button just once.
You should tell us if you can enter the bootloader,you used HSPL or USPL, this way someone could help you.
My opinion is that you should flash again using the card method.But for this to work you should have the HSPL and be able to enter bootloader.
So some more info would be good.
Good luck.

OK..
I have HSPL.
I downloaded bootloader from http://forum.xda-developers.com/showthread.php?t=347700
I set all what I should and press ok and than I see "USB port can not open".
I can't find card method for blackstone.

Ok.
It is simple enough.Just folow the next steps:
1. Download a rom that you like.
2. Rename the .nbh file to BLACIMG.nbh.
3. Copy BLACIMG.NBH into the root dir of your Storage Card.
4. Be sure to have at least 30% of charge.
5. Turn off your device by using the Power Button
6. Go to bootloader mode. Push and hold Vol Down + press Power button.
7. As soon as presented the message, push Power button to start flashing or Volume Down button to cancel.
8. The whole procedure will take about 3 minutes. After you finish and see the relative message, soft reset your device, you are ready.
Good luck and keep us posted.

Now I have problem with bootloader mode. I put in micro sd, turn on bootloader mode (poweron with volume down) and than in device I have
"Black100 32M
SPL-1.56.oliNex
MicroP-BlackStone (LED) v6"
on red-green-blue-white background
And for half second device show
"Loading!
No Image file"
Whats wrong?

2 Things:
1) Make sure you called the file BLACIMG
2) Make sure you place the file in the root of your SD card, not a folder.

Everything I did, how you told me. It isn't working still.

OK.. Thank you very much.
My device is working now.
I cant belive i just put in SIM card
And restore device to factory default settings.
Thank you a lot.

Domin1992 said:
OK.. Thank you very much.
My device is working now.
I cant belive i just put in SIM card
And restore device to factory default settings.
Thank you a lot.
Click to expand...
Click to collapse
Excellent

Domin1992 said:
OK.. Thank you very much.
My device is working now.
I cant belive i just put in SIM card
And restore device to factory default settings.
Thank you a lot.
Click to expand...
Click to collapse
You are welcome. Glad that all is good.

[Q] Cannot acces Tricolor screen. Stuck at in MAGLDR

Long story short, I was attempting my second flash. I followed the steps before and everything was going fine. Now right before i open CWM to install android the MAGLDR ( which is version 1.13 ) gets stuck at "123456GOGOGO".
Now i thought maybe i would start my proccess over but I cannot acces the tricolor screen. I wasnt able to do this in the beginning of my proccess either, when i pulled up my HSPL program on my desktop my computer entered the tricolor screen on its own and I proceeded from there.
Basically i have looked around and have found some ways out of the GOGOGO problem, yet I cannot acces the Tricolor screen using hardware buttons so I am stuck. And its not a hardware issue. In MAGLDR the Vrockers work fine and before I did anything the rockers were working fine in Windows 6.5.
Any Ideas? I have a feeling i got a pretty nice paperweight now.

the normal way to enter the tricolor screen is to turn the phone off then hold the volume down button and momentarily hit the power button.
Also, To keep from getting to the 123456 GOGOGO hold the power button while it is booting normally and you will get to the MAGLDR menu and there you can go to the AD Recovery and flash a new rom.

hunterthehuman said:
Long story short, I was attempting my second flash. I followed the steps before and everything was going fine. Now right before i open CWM to install android the MAGLDR ( which is version 1.13 ) gets stuck at "123456GOGOGO".
Now i thought maybe i would start my proccess over but I cannot acces the tricolor screen. I wasnt able to do this in the beginning of my proccess either, when i pulled up my HSPL program on my desktop my computer entered the tricolor screen on its own and I proceeded from there.
Basically i have looked around and have found some ways out of the GOGOGO problem, yet I cannot acces the Tricolor screen using hardware buttons so I am stuck. And its not a hardware issue. In MAGLDR the Vrockers work fine and before I did anything the rockers were working fine in Windows 6.5.
Any Ideas? I have a feeling i got a pretty nice paperweight now.
Click to expand...
Click to collapse
pull your battery,
put it back in,
hold down volume and power button,
and theres your tricolor screen

True i know about to Volume Down and power key to enter Tricolor, but for some reason with my phone that does not access the Tricolor, tried it many times.
Holding the power button while it booted made no difference.
*******I followed these steps for flashing my rom:*****
First, you need your files!
HSPL4
MAGLDR 1.13
Clockworkmod Recovery
Download a ROM of your choice, I prefer Hyperdroid
Unzip only the first 3 files, and place the ROM zip on your SD card.
So, here we go!
Remember to back up all of your contacts and any data stored on the phone that you want to keep, because you will be wiping windows off ENTIRELY.
HSPL4-
Plug in your phone.
Right click the HSPL4 file and select "Run as Administrator"
Go through the screens, then when it's connecting to your phone your phone will go into bootloader (red, blue, and white screen)
Select HSPL 2.08 when it comes up, hit next. Let it work.
It'll popped up saying "We hacked it!", and you'll see it on your phone. Click yes, then ok and you're done with this step! Phone will restart.
MAGLDR 1.13-
After phone's restarted, go to the MAGLDR folder, right click "ROM Update Utility", and Run as Administrator.
Checkmark the necessary boxes to continue through steps. Then click "Update", then click next through screens.
Once it starts updating ROM image, it taks about 2 minutes. Then click finish.
Phone will reboot into MAGLDR.
Navigate MAGLDR using the volume up and down keys. Use the green button to select (you may have to click twice).
(At this part in the video I uploaded the ROM zip, I'm assuming you already loaded it though, so skipping on).
Flash Clockworkmod_150
Scroll down on MAGLDR to option 5 "USB Flasher". Don't select it yet.
On your computer, go to the Clockworkmod folder, right click the DAF file and run as administrator.
Click next until it gets to waiting for USB.
Now press the green button to put it in the mode.
Text will start to appear on the phone screen, and the Clockworkmod flasher will do its work.
Once done, click finish, and MAGLDR will reboot. It may say something like "kernel fail", it's normal, don't worry about it.
Scroll down to number 8 "AD Recovery", select it.
It'll say Go Go Go Go, and then you'll be in Clockworkmod Recovery!.
****************************************************
BUT! at this point i get stuck in GOGOGO and i have to remove battery.
I JUST got this phone and really want to atleast get it back to Windows Mobile so i can restart my flash.

read the link in my signature...i was there and few of the folks succeeded after completing the process

Hoping it wouldnt come to this but looks like i dont have a choice, hopefully I get a try your method out tomorrow since the success rate looks promising, Ill get back with the results!

Try to reset your phone. Push the red little button on the back near the SD card

I have the HD2 open and have removed the flex cable at the bottom of the phone yet when i connect USB it auto boots so i have to power it down and to do that i have to connect flex cable. once i have the cable connected i power down then i hold the volume button and before i can restart the phoen autoboots from the USB being plugged in so im in a loop.
But i cant boot without the USB being in so Im in a pickle. Again

hunterthehuman said:
I have the HD2 open and have removed the flex cable at the bottom of the phone yet when i connect USB it auto boots so i have to power it down and to do that i have to connect flex cable. once i have the cable connected i power down then i hold the volume button and before i can restart the phoen autoboots from the USB being plugged in so im in a loop.
But i cant boot without the USB being in so Im in a pickle. Again
Click to expand...
Click to collapse
Try this:
- Hold down the vol_down button and don't let go.
- connect the usb, don't let go of the vol_down button
- should go into bootloader
- now let go of the button.

Nope that didnt work either, any OTHER reason my phone wouldnt acces the Tricolor screen? Ive tried everything 100 times.

[HELP] Restoring of brick Huawei U8800

Restoring of brick Huawei U8800.
All do at your own risk! I am not responsible for your machines!
Today I was able to magically (just wonderful, because it found the time at which there is a chance to run the update) to recovery from a brick Huawei U8800 (corrupted bootloader + recovery not run + in a pink screen not mounted hard drive + when trying to update the written Update failed! I spoke to a service center, they said the warranty is not the case and we must change the motherboard (the cost of 3-4 million BYR, new at the MTS salon cost 2.9 million BYR )
What and how I did:
1) To restore I'am using the firmware B162 Android.
2) Format the micro SD card that was clean (I was 8 gb, 2 class and be sure to FAT 32) and unpack "dload" folder and ".txt" file(with a strange name) from the downloaded archive to sdcard.
P.S. I say that not all flash drives can operate restore, I have like three went, normally only one.
3) Insert the micro SD into the phone and pull out the battery.
4) Hold down the Volume (+) and power up, hold and connect the phone via cable to your PC, your phone will be switched on and the logo appear, then turned off my phone (missing logo). So, when the logo will disappear (ie the phone will turn off) and immediately hold down the volume (-) the volume (+) and power up.Main that the updating process can start only one time after the logo was gone, if after a few times in a row press both the volume keys and power up, updating does not start, it is necessary to re-clamp the volume (+) and the power up, after the disappearance of the logo, both the volume and the power up of ... I have to go to the upgrade process if you wrote "Update failed!", try again (I went with 2 times).
5) After a successful update, the phone will reboot, on reboot he should loaded the standard blue recovery.
6) Turn off the phone from the computer, insert the battery, hold down the volume (-) the volume (+) and turn on, wait until you get a pink screen, release the button and connect it to your computer. You should see a new device and to define a disk drive with a folder "image". If we define - rejoice!) If not, then you need to install the driver on the internet enough to the driver, as well as the wood in my going to the Android SDK, not sure ...
7) Thus, we can assume the phone repaired) Download recovery 4.0.0.5 and unpack the archive and copy the file "recovery.img" to a folder "image" with the replacement. A man does not 4.0.0.5 recovery loaded, it is strange, but recovery 5.0.2.7 normally loaded
8.) Disconnect the phone from the computer, pull out / insert the battery and try to enter the recovery (volume (+) and power up).
9) If set, then everything is OK and can now be sewing. I still put 2.2 Geno v8.4 + software package from Google, but I recommend again read all instructions on the firmware, to avoid problems!
Good luck, hope that helped someone, he sat on the forums more than one day, but have not found a solution.
If someone has turned out, a sign of gratitude you can throw money on my phone +375297176005 (MTS, Belarus), would be very grateful
P.S.
Instructions is my and it's my first, that do not copy and paste, you can search the Internet. Do not judge strictly, if something is not designed ...
If there are people who helped, I think you can throw his hat in the description. My message is also present in our 4pda.
Hope springs eternal
Sorry for my english, I'm from Belarus and bad know it

Before the restoration, can you open your phone? Mine was completly down. I can't power on or go to recovery or install any official roms.

Özgürce said:
Before the restoration, can you open your phone? Mine was completly down. I can't power on or go to recovery or install any official roms.
Click to expand...
Click to collapse
my phone is also not included, only in
a pink boot screen, but on the computer the drive was
not detected

Please, if someone came to restore, write

greeshan said:
Please, if someone came to restore, write
Click to expand...
Click to collapse
omg, this looks so sad, I guess we are in the same page. BRICK phone. no power, no screen no nothing... well, actually no, it vibrates when battery is inserted or cable is connected, but, other than that, niente.

I had follow all ur instruction but when i press volume up + power with usb connected it goes to the CWM...so i just press vol up + down + power...It goes PINK SCREEN...Any more solution please?

i did it! but after 5 times i see this message: "update failed"

i have the same problem

r0y123 said:
i have the same problem
Click to expand...
Click to collapse
Hello, I have a problem after changing recovery.img. Now after power on only error message: Image signature verify fail. Your boot/recovery image may have an incorrect signature. Please update your image to a signature official one. You can remove battery for power down.
When I get to pink screen - no disk appears in my PC. Please, what can I do now?

greeshan said:
Please, if someone came to restore, write
Click to expand...
Click to collapse
My update process stops at 1/4 of the bar.What can i do?

greeshan said:
my phone is also not included, only in
a pink boot screen, but on the computer the drive was
not detected
Click to expand...
Click to collapse
Just thought I would mention it, if you connect the pink screen to Ubuntu/Linux, it will most likely mount.

Just tried this recovery method on a bricked U8800. Didn't do anything at all. Must admit that it was bricked in a way that i didn't see anything at all on the screen. Neither did i notice anything in dmesg on a linux machine.

Help
Hello.my huawei u8800pro v.2.3.5 brick after install official ice cream sandwich.I followed the procedure and now I have a new removable but I can't go to recovery mode!!can I install a new rom?

[Q] won't go to bootloader htc hd2 t mobile

i have htc hd2 t mobile us
on windows phone 6.5 it never goes to boot loader mode by pressing the power key and the vol down it never respond to any thing before the start of windows 6.5 and i want to setup android but how i can without boot loader mode ????
plz help

Turn off phone .. HOLD volume down rocker, PRESS & RELEASE power button WHILE STILL HAVING THE VOLUME DOWN ROCKER HELD .

There are apps for Windows Mobile like BsB Tweaks and Anastasia End Key that allow you to co to the bootloader via a bootloader.exe file. But be warned that ones you no longer have Windows Mobile on your HD2 you will once again have to use the power and volume down button o get to the bootloader. I am on my Sensation posting right now so I am not going to type out a lengthy walk through right now. But if you are still interested in running Android PM me and I will try to put together a walk through that is suited to your situation.
Also it sounds like your volume down button is malfunctioning, which to be honest is not good as it can cause you to have a un usable device if you are not careful.

the same here
my phone have the same messeng, i try to press vol down and power and nothing, vol up and down nothing... what i can do?

T-Macgnolia said:
There are apps for Windows Mobile like BsB Tweaks and Anastasia End Key that allow you to co to the bootloader via a bootloader.exe file. But be warned that ones you...
...Also it sounds like your volume down button is malfunctioning, which to be honest is not good as it can cause you to have a un usable device if you are not careful.
Click to expand...
Click to collapse
I have same problem...
WM 6.5 Artemis in NAND, microSD 32G.
Now I have new microSD 64G, and I would try NativeSD, but bootloader can't work.
The volume button with phone calls and with MP3 works!
Any help?
Thank you!

can we have a bootloader.exe-like file and put it in memory card to run as a autorun
T-Macgnolia said:
There are apps for Windows Mobile like BsB Tweaks and Anastasia End Key that allow you to co to the bootloader via a bootloader.exe file. But be warned that ones you no longer have Windows Mobile on your HD2 you will once again have to use the power and volume down button o get to the bootloader. I am on my Sensation posting right now so I am not going to type out a lengthy walk through right now. But if you are still interested in running Android PM me and I will try to put together a walk through that is suited to your situation.
Also it sounds like your volume down button is malfunctioning, which to be honest is not good as it can cause you to have a un usable device if you are not careful.
Click to expand...
Click to collapse
can we have a bootloader.exe-like file and put it in memory card to run as a autorun file on device for going to bootloader mode?

hoseinpour_a said:
can we have a bootloader.exe-like file and put it in memory card to run as a autorun file on device for going to bootloader mode?
Click to expand...
Click to collapse
If you still can boot to Windows Mobile yes you can. But if you can not boot to Windows mobile than the only file that the device will recognize is a .nbh file and you have to boot to the bootloader for it to do that. If you can not boot to the bootloader manually by holding the proper button combo while booting then you have a hard bricked device and it needs to be JTAGed.

T-Macgnolia said:
If you still can boot to Windows Mobile yes you can. But if you can not boot to Windows mobile than the only file that the device will recognize is a .nbh file and you have to boot to the bootloader for it to do that. If you can not boot to the bootloader manually by holding the proper button combo while booting then you have a hard bricked device and it needs to be JTAGed.
Click to expand...
Click to collapse
it was a very useful and technical answer. thank you. how i can do JTAG for htc touch hd ?

hoseinpour_a said:
it was a very useful and technical answer. thank you. how i can do JTAG for htc touch hd ?
Click to expand...
Click to collapse
To do TAG you have to harvest the main board from the device and attach a JTAG to it. The connect the appropriate cable to the JTAG and to a Riff Box. The Riff Box connects to your computer and you then run software to reserect the bootloader. But this the riff box is expensive so I suggest you contact someone that does this for a small fee such as MobileTechVideos.com

[Q] 3 days strait nothing works hd2 android no root <3e> recovery no usb

HI all, thank you for your time.
I recently inherited a htc hd2 that has android 2.3.4 on it, model T8585 baseband ver maui.11amd.w11.19.sp.v1, 2011/06/23 00:50. kernel 2.6.35.7. build number 10hx2p.h3.111121.ad2_3_4_v1.wvgac_cn.com_v01_3g.
I don't know what any of that means but for 3 days I have been trying to put ICS on my phone but cant get any of the apps to connect to the phone via usb, htc sync, win mod sync, no rom apps connect, moborobo will connect, and accessing the sd works but that is all.
I do not have clockwork recovery and can not install, my recovery program is <3e>.
even though android is running on the phone it will not allow root access.
I have downloaded and installed all the java and sdk stuff, could not manualy install usb connection drivers, my os is win 7 64.
I am going mad, every turn seems to be a brick wall, but not a brick phone yet, please help!

don't worry
Hi dj,
well it sounds like the most important stuff should be on your phone. However, I'm missing the following information:
Do you have magldr or CLK installed?
To find out, do the following:
Turn on your phone (with the hangup-key), right after feeling the bootup vibration press and hold the hangup-key again.
If you have a working magldr or CLK installed it should show up now.
The version is also important, my MAGLDR is version "1.13".
Tell me what your phone has installed please and I'll try to help more.
Greets

rubb3ld1ek4tz said:
Hi dj,
well it sounds like the most important stuff should be on your phone. However, I'm missing the following information:
Do you have magldr or CLK installed?
To find out, do the following:
Turn on your phone (with the hangup-key), right after feeling the bootup vibration press and hold the hangup-key again.
If you have a working magldr or CLK installed it should show up now.
The version is also important, my MAGLDR is version "1.13".
Tell me what your phone has installed please and I'll try to help more.
Greets
Click to expand...
Click to collapse
thanks for the quick reply, no I can not install that stuff, when I go into recovery mode it is <3e> recovery not clockwork, I can not install them because my phone does not seem to support native usb, I have tryed to install them from the sd card, I have tryed to install CLK from the app at the google download store, nothing works, I have red that i should roll back rom to win but cant to that without htc or other sync working, I have read roll recovery back to <2e> using the sd card but cant do that, I cant even root the phone because everything requires that a usb sync work or that CLK already be on, I;m going round in circles.

dj.asynchronous said:
thanks for the quick reply, no I can not install that stuff, when I go into recovery mode it is <3e> recovery not clockwork, I can not install them because my phone does not seem to support native usb, I have tryed to install them from the sd card, I have tryed to install CLK from the app at the google download store, nothing works, I have red that i should roll back rom to win but cant to that without htc or other sync working, I have read roll recovery back to <2e> using the sd card but cant do that, I cant even root the phone because everything requires that a usb sync work or that CLK already be on, I;m going round in circles.
Click to expand...
Click to collapse
okay, I don't know if I get you right? You have android on your HD2 but you don't have MAGLDR or CLK (those are bootloaders, not recoveries)?
Magldr looks like this: http://www7.pic-upload.de/17.02.11/n35i2xpo9mg.jpg
And you enter it this way (if you should have it): pull out battery -> put back in -> press and hold the power key until you see the magldr screen (takes maybe 5 seconds).
My problem is that I'm not sure how your phone is setup. Please try to clarify.
If you have or had a working android on your phone, I'm pretty sure that you also have MAGLDR or CLK installed.
However... if you don't have it yet please download the HD2-Toolkit from here: http://forum.xda-developers.com/showpost.php?p=19931919&postcount=50
Thats a good tool to install either: magldr or clk. And once you have it I'll try to help you with that.
Greets

rubb3ld1ek4tz said:
okay, I don't know if I get you right? You have android on your HD2 but you don't have MAGLDR or CLK (those are bootloaders, not recoveries)?
Magldr looks like this: http://www7.pic-upload.de/17.02.11/n35i2xpo9mg.jpg
And you enter it this way (if you should have it): pull out battery -> put back in -> press and hold the power key until you see the magldr screen (takes maybe 5 seconds).
My problem is that I'm not sure how your phone is setup. Please try to clarify.
If you have or had a working android on your phone, I'm pretty sure that you also have MAGLDR or CLK installed.
However... if you don't have it yet please download the HD2-Toolkit from here: http://forum.xda-developers.com/showpost.php?p=19931919&postcount=50
Thats a good tool to install either: magldr or clk. And once you have it I'll try to help you with that.
Greets
Click to expand...
Click to collapse
I do appreciate your help, I had already installed the toolkit but it will not connect to the phone(no pc based "phone hacking"software will connect to the phone. the usb works fine only to access the sd card, moborobo will synch with phone but nothing else.
when i hold vol down and on, the phone boots into <3e> recovery, <3e> is not an emoticon, it is the name of the recovery app the phone boots into, not any clockwork, magldr thing.
I think I could sort it all out one way or another if I could flammin ROOT! my phone, but all the methods I have found involve using a sync program that i cant use because they will not communicate with the phone.
I know it seems strange that a windows phone has android on it without being rooted or having other stuff going on, but I assure you this is the case.
I'm obviously missing something but I don't know what it is??? I's there a way to root the thing from the sd card, or is there a hidden box that i just have to check to access the root? I'm lost bro http://forum.xda-developers.com/images/smilies/eek.gif

PLEASE DON'T follow those steps. As Nigeldg pointed out: there are incorrectnesses in my post!
Follow this link instead: http://forum.xda-developers.com/showthread.php?t=1044830
Okay, I think I kinda get where you're stuck at.
Here is what I think I would do, just out of my memory:
- Install the Toolkit again. Start program and in there download the drivers (button in the right corner) and install them properly.
- Boot phone and press down the volume down key (exactly like this: click on power button, release power button, hold volume down and keep holding), to get into three color screen.
- Connect your phone via usb and wait until it says USB on the phone (instead of serial)
- if it should not switch to USB, your Windows does not connect to your phone, because of a driver problem (maybe you have to reboot your pc ​once?!)
- start your toolkit
- press Wipe (Task 29) --> this will erase everything on your phones NAND
- follow instructions
- next press install HSPL
- follow instructions
- reboot phone
- press Install MAGLDR
- follow instructions
- boot phone and keep holding the power button until you see the MAGLDR menu
- move down to "5. USB Flasher" (with volume down)
- press call button to enter
- wait until it says USB....USB
- in the Toolkit, on the left side choose your partition size (my suggestion 200mb main and 45 cache)
- press repartition
- follow instructions
- reboot phone into MAGLDR again and move down to "8. AD Recovery"
- press call button to enter
- move down to mounts and storage
- press call button to enter
- mount USB-Storage (your sd-ccard)
- your computer should show your SD-Card
- download your favorite ROM and move the .zip to the SD-Card
- back on your phone unmount USB-Storage
- go back with back button
- move down to "install ZIP from SDcard" and choose the desired zip file
- follow the installer and reboot into MAGLDR afterwards
- in MAGLDR move down to "10. Services"
- press call button to enter
- and press call button again on "1. Bootsettings"
- and again on "1. Boot Source"
- then move down to "2. Android from NAND"
- and finally press call button to finish this
- Now move cursor to "3. Boot AD NAND" and press call button.
-> Your phone should boot up android and set it up for you, give it some time, even after seeing the login screen.
Reading your last answer, I think your problem is right at the beginning of what I wrote. You can't even get into the 3 color screen?!
If this should not work please tell me at what point of my instructions you are stuck.
Greets

Nigeldg said:
@OP, Actually please don't follow that guide. Just reading a few lines shows that:
1. It says to Task29 (never a necessary step)
2. It then says 'install HSPL'. Either HSPL 2.08 is already installed (so this step isn't needed) or you've just messed up your phone by trying to flash Task29 without HSPL
3. It says to repartition with a 200MB system and 45MB cache - you actually repartition as per the ROMs requirements, and 45MB cache is just a waste of space (most ROMs recommend 5, people have flashed as low as 2MB without issue)
4. It says to transfer the ROM to your SD card via CWM, which can cause the .zips to be corrupted. Always transfer via an SD card reader if possible, or within an OS (not MAGLDR or CWM).
5. It says that you have to set the boot settings to AD NAND when you don't
Whilst it's great that you're trying to help people out and write your own guides, don't do so when you're ill-informed and don't really know what you're doing. It's best just to stick with already existing guides.
@OP, try the guide in my sig if you're looking for one which is easy to follow, has clearly outlined steps and is (most importantly) correct.
Click to expand...
Click to collapse
^The same post I wrote on the other thread

Hey Nigeldg
thanks for your advance in this. Thanks for pointing those out. Will correct that and point to the links in your signature from now on.
Greets

rubb3ld1ek4tz said:
Hey Nigeldg
thanks for your advance in this. Thanks for pointing those out. Will correct that and point to the links in your signature from now on.
Greets
Click to expand...
Click to collapse
" Boot phone and press down the volume down key (exactly like this: click on power button, release power button, hold volume down and keep holding), to get into three color screen".
when I follow this step my phone goes into <3e> recovery, not red blue green clockwork, "<3e>" is my recovery, it is a screen with "!" in a triangle and a little android dude.
my recovery does not let me install unsigned stuff so even though I can put things on the sd card, I can not install them from there.
the phone does not sync with any toolkit, install, htc, win, android, or other even though htc, and android drivers are in my device driver list.
my phone is not rooted.
I do appreciate all your help guys, I will keep looking arround the forum, I found some posts about my <3e> recovery and mods so it will allow install of non signs apps, peace.

dj.asynchronous said:
" Boot phone and press down the volume down key (exactly like this: click on power button, release power button, hold volume down and keep holding), to get into three color screen".
when I follow this step my phone goes into <3e> recovery, not red blue green clockwork, "<3e>" is my recovery, it is a screen with "!" in a triangle and a little android dude.
my recovery does not let me install unsigned stuff so even though I can put things on the sd card, I can not install them from there.
the phone does not sync with any toolkit, install, htc, win, android, or other even though htc, and android drivers are in my device driver list.
my phone is not rooted.
I do appreciate all your help guys, I will keep looking arround the forum, I found some posts about my <3e> recovery and mods so it will allow install of non signs apps, peace.
Click to expand...
Click to collapse
This may sound silly but always best to check the simple things 1st, do you have windows mobile device center installed?

I am not entirely convinced you have a HD2. you may have a clone.

I'm inclined to believe RobbieP's right. I've never heard of this recovery ever being used on an HD2. You claim that you're not rooted (all of the HD2's ROMs are rooted bar the DFT Stock Desire ROM) and you also say that when you boot up there is an ! in a triangle. None of these things should really be happening on an HD2.
Secondly, you seem to be very confused about your terms. Please read the guide in my sig about that, as if you somehow do have an HD2 then you should be aware of all of those things before flashing.
If possible, could you post some pictures of your phone and also the settings info etc.? It might help in determining if it's a fake.

swukjay said:
This may sound silly but always best to check the simple things 1st, do you have windows mobile device center installed?
Click to expand...
Click to collapse
Yeh, it's installed, but just to be certain, after your question, I reinstalled it, still no good.
Im going to try to root the phone latter, will look around on this forum for a non usb style root.
yeah I suppose it could be fake, I have only seen on forums of Samsung phones using this recovery, It was bought on eBay cheep, when I do a factory reset it goes Asian on me, it looks exactly like the hd2.
As far as getting some terms mixed up, sorry, I had put in a lot of reading and trial and error before asking for help, It's hard to gauge how long to grind away at something before asking for a tip.
I will post some pics of the phone latter
thanks again for all your help guys.