[q] stuck in bootloader. Help needed. - Advantage X7500, MDA Ameo General

have a HTC Athena x7500.
Im stuck in bootloader.
Wend I power on the device it goes directly to bootloader and
the screen say :
ET \ Njq
IPL - v1.00
ET \ Njq
SPL- v1.20. Olipro
USB( wend is connect )
serial ( wend is unconnect )
I dont remember what it was befor I try to flash a WM 6.5 rom on it.
It as a WM 6.1 in Portuguese Rom befor my attent.
I cannot power off the device by pressing the button but have to take
the battery.
I already try to change the rom, the SPl and put everything inside just
to try to move from were I am but no results.
Began to update but ends or in 1% or in 7% and loose the connection.
The device connects to the PC but in PC in WM device center nothing happens.
I try Win7 and also XP.
I went to HTC site to download the official portuguese ROM but there are no
ROM to download.
So I´m dead on the water.
I will apreciate very much any kind of input that take me out
of were I´m now.
I´m not a expert as you already notice.Please keep it simple.
Thank you

stuck in bootloader. Help needed.
stuck in bootloader. Help needed.
have a HTC Athena x7500.
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl spstuck in bootloader. Help needed.l is 1.10
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed!
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
J have explored ruu_signeg.nbh with notepad jai entered the signer spl 1.10 I know if c is vrait or name
I believe there is a problem in the image rom saved in my athena rom
what I see on the screen of my athena is the spl 3.05.0000
The real spl is 1.10.0000 there is confusion in my spl
is what I can fix this problem with mtty
so if possible please guide me
sorry for my bad Englis
thank you in advance
My email: [email protected]

Related

help!!!dead hermes!!!

help!!i really no idea with my devices as i try to flash it to wm6,then it stop at 50% and reboot then hang at bootloader screen,i try to flash again but when it reach 1% it will restart and update error msg prompt, it said "the image is corrupted" if im using sd card flash,it come out 00068002 on the top of the"loading" words then go in the tri colour screen again. anyone pls help me pls!!!!!!!!!!!!
Man I wish you guys would do a LITTLE research on how to flash stuff... I bet you don't have Hard SPL installed even though its splashed about all over the forum.....
Try to download the SHIPPED STOCK ROM again... It seems you have a corrupted download.
Once you have downloaded the rom, then reset Hermes into TRUE bootloader, not the failed flash you are getting.
On the PC, untick "Allow USB connections" in active sync the connect Hermes.
Double click on RUU_Wrapper.exe of the freshly downloaded rom. Follow prompts...
Pray......
Then, if it works, INSTALL HARD SPL V7...........
thanks for rely brother,i hv tried download a shipped rom from here and i hv follw all the prosedure u thought,it still doesnt works,oh no....................
Error 226 flash write
Hello friends i'm italian and sorry for my english.
I have a problem with my hermes200.
I have flashing on my tytn a rom kitchen using "package tool by bepe" with nb IPL, SPL, Mainsplash, Subsplash, ExtROM and GSM extrated from original rom htc tytn wm6 and a OS.nb extrated from rom kaiser ITA wm6.1.
When the flashing is termined the hermes don't start: push power botton but the screen is black and only green light is ON.
I have flashed original htc hermes wm6 but i have "error 226 flash write" when the process is at 89%.
I have IPL-1.04 and SPL-2.04. CID.
SPL 2.10, SPL 2.20, SPL 2.30 are not possibile to install.
i have try command with mtty tool:
- task 32 -> FF
- task 28 -> format storage success
- task 2a -> fix bad block
- info 8 -> much bad block Os Win CE
I've try to reflash the original rom but the problem is the same
The battery don't possibile to charge and level should be of 40%.
Help me please....
Tanks!!!

Artemis experts help me

I have artemis arte100 and i am not able to connect to activesync and when i try to flash with orginal rom with cube its going upto 3% and then jumping to 100% its not flashing and when i try to upgrade the rom with sd card its showing that invalide certificate some one please help to upgrade me artimes
Flash your Artemis by cable/pc connection.
Connect your PDA to PC via USB cable.
Enter Artemis in boot mode (hold ON voice speed dial, and do "SOFT RESET").
When your see "three color" mode, just wait to finished flash.
SPL not unlocked
smichandu said:
I have artemis arte100 and i am not able to connect to activesync and when i try to flash with orginal rom with cube its going upto 3% and then jumping to 100% its not flashing and when i try to upgrade the rom with sd card its showing that invalide certificate some one please help to upgrade me artimes
Click to expand...
Click to collapse
Hey dude...,
Your SPL is still not properly UNLOCKED....
You need to SPL unlock your phone first...

Urgent help: HTS P3300 stuck up

Dear All,
Please urgent help required.
my HTC P3300 (Artemis) stuck up when i was trying to start it up. when i use to turn my cell on, i goes to the starting screen shows the following numbers and then stuck up.
IPL 3.07.0001
SPL 3.07.0000
GSM 02.69.90
OS 3.7.0.0
the screen does not move after that. i tried soft reset through the reset button but result is the same.
i also tried hard reset and when i puch the green phone button to proceed, a message come "FORMAT FAILED" and the phone stucks up.
i am quite a lot of problems since i have upgraded to WM6 from WM5 last week.
i am quite sucked with this problem. not been able to use my set since yesterday.
please also note that my HTC was not syncing with my PC since i have upgraded to WM6.
PLEASE HELP URGENTLY.
Nomi
You can tried to reload your last ROM (WM6), for this :
-Start in bootloader mode ("Voice Command" + "Power" + Reset with Stylus)
-Start a new upgrade Rom (With the last ROM)
It's works ?
If yes, you can upgrade Radio and SPL.
i did that but the flash process stopped at 3% (i think CID locking problem). i tried USPL but the process could not be done. i also dont have my previous ROM but i noted the previous numbers which are
IPL 1.14.0001
SPL 1.14.0000
GSM 2.67.90
OS 1.14.0.0
tell me what to do now??
i dont have my previous ROM. nor i know what were the factory provided ROM
please help
You can :
-Flash your original ROM (Operator and langage)
-USPL and 1.11.cmon (verify that your phone is USPL before another action)
-Upgrade your new ROM.
i dont have the original ROM.
the phone is stuck at boot page. USPL not working.
what to do now
You must to download a rom from the Same Operator and same location.

Artemis problems with USPL

Hello guys, I've got a p3300 which I can't update to a WM 6.1. It's the factory's 6.0. It's originally simfree so I dunno if I need to go through the USPL.
The thing is that it gives me 270 Corrupted image error.
As I thought that being simfree originally, didn't need to do CID unlock, I tried to flash a cooked ROM with no success whatsoever.
Any ideas?
Kind regards,
JamworkS.
DONT try to install any rom untill you flash ''uspl cmon''!
you might brick the O2xdaOrbit/p3300!!
* put the two cab files on your device and run them.
* get activesync connection
* run dos window
* soft reset after 100% to get activesync connection.
- only when the rom update utility window opened on pc..
* uspl cmon rom update utility.
***ONLY after doing uspl is it safe to flash a rom.
* if you have an SD card in the device, take it out..
when you have done uspl on your device startup you will see..
SPL: 1.11.cmon
* its done.
USPL 1.11.CMON
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
message me if you get stuck..
Having problems with this.
For 2 days I try all the files and ways to set 1.11.cmon on my P3300 and always stuck at one place no matter what versions of the program I get.
IPL 3.07.0001
SPL 1.11.0000
GSM 02.98.90
OS 3.13.0.0
are the red numbers I see when I restart it.
The problems are that when connect phone and see connected on ActiveSync I start start_uspl program. After 100% connection with Active Sync dissapears and I see black screen on my PPC, then I run ROMUpdateUtility and It says some error that there is no phone connected.
If I start ROMUpdateUtility before start_uspl I go in to boot loader mode ( the 3 colors screen ) and then again that there is no phone connected.
I have done this 15 times or more with different versions of the program and it stucks on the same places ALL the time no matter what version I use.
My artemis had 1.11.cmon before, but I installed the LAST Artemis P3300 ROM from the WIKI. That removed the 1.11.cmon from the phone. After that I have Installed Vanilla 2.0 WWE version on the phone and started the process to set 1.11.cmon on the phone. No success. After some 6.5.5 ROM from the forum, then process to set 1.11.cmon and again nothing...
Please HELP!
i am also having the exact same problem with this , have tried everything to get this to work.
iant2008 mate I did solve the problem
All works as the brains here say. My problem was that I am using Windows 7 at home and Windows Vista at other place I did try to fix this problem. However with Windows XP this whole operation works properly as the people here say. Big thanks to them and I hope you success in this operation too
raving_nanza said:
DONT try to install any rom untill you flash ''uspl cmon''!
you might brick the O2xdaOrbit/p3300!!
* put the two cab files on your device and run them.
- Cert_SPCS
- EnableRapi
* get activesync connection
* run dos window
* soft reset after 100% to get activesync connection.
- only when the rom update utility window opened on pc..
* uspl cmon rom update utility.
***ONLY after doing uspl is it safe to flash a rom.
* if you have an SD card in the device, take it out..
when you have done uspl on your device startup you will see..
SPL: 1.11.cmon
* its done.
USPL 1.11.CMON
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
message me if you get stuck..
Click to expand...
Click to collapse
* soft reset after 100% when the rom update utility window opened on pc..
''to get activesync connection''
it should work dude
Dear Friends,
After USPL the screen of Artemis becomes white and running RUU ends up with error 266. And even after a soft reset running RUU ends until 3% after that comes error 270.
Any solution will be highly appreciated.
Thanks and regards,
Sameeha
...
sameeha said:
Dear Friends,
After USPL the screen of Artemis becomes white and running RUU ends up with error 266. And even after a soft reset running RUU ends until 3% after that comes error 270.
Any solution will be highly appreciated.
Thanks and regards,
Sameeha
Click to expand...
Click to collapse
put the 2cabs on your device and run them..
rapi & cert
run_startuspl - on pc
when this is 100% - soft reset device
-now continue to do rom update utility (uspl ruu)
this should work..?
Hi, raving-nanza,
Thank you very much for your advise. I did that too but nothing happened, error 270 again. errrr? very irritating dude? Any other solution?
Cheers,
Sameeha
...
sameeha said:
Hi, raving-nanza,
Thank you very much for your advise. I did that too but nothing happened, error 270 again. errrr? very irritating dude? Any other solution?
Cheers,
Sameeha
Click to expand...
Click to collapse
i have to admit, i had same trouble to do uspl1.11cmon but eventually it worked.. frustrating.. i know.. but keep trying.. if i was you i would flash back to the official rom.. which should get rid of 1.11.0000 and set back to original spl..
i put rapi and cert on my device, ran them, connected to pc, ran ''run_startuspl'' that made penguin on screen on device.. went to 100% then white screen.. Ruu automaticly opened on pc but i didnt continue with Ruu.. i soft reset device, got activesync connection again and then i continued with the open Ruu..
(Ruu - rom update utility)
Thanks RN, you know, I was trying all this time and my Artemis frozen now (freezes on startup screen IPL 1.25.0001 / SPL 1.27.0000 / GSM 02.69.90 / OS 3.4.0.0. and dopod logo) not moving further. Whats going on? Can you help me?!
Cheers,
Sameeha
...
add me to messenger..
will be much easier than posting
i'm an idiot.....
see this thread
http://forum.xda-developers.com/showthread.php?t=578406
if you run a 3.13 rom; get the 3.13 cmon
if you run a 3.15 rom; get a 3.15.com.
pof's original (kickass great work!!) didn't work with my 3.13 (original htc rom); i ended up with 1.11.000spl. i then ran the 3.13 uspl (see thread); now i am on cmon version

found spl v1.10 dowload Spl before v3.05 is not allowed!htc x7500

stuck in bootloader. Help needed.
I have a HTC Athena x7500.
accidentally upgraded my htc x7500 WITH SSPL-Manual-x7510.zip of HTC X7510
Wend I turn on the device, it goes directly to bootloader and
the screen is:
ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl is 1.10.0000
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).
I can not turn the unit off by pressing the button, but must take
the battery.
I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:
found spl v1.10
dowload Spl before v3.05 is not allowed!
I tried to update it with the sd card i have the same mesage
upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work
I have explored ruu_signeg.nbh with notepad jai entered the signer spl 1.10 I know if c is sure or not
I believe there is a problem in the image rom saved in my athena rom
what I see on the screen of my athena is the spl 3.05.0000
The real spl is 1.10.0000 there is confusion in my spl
is what I can fix this problem with mtty
so if possible please guide me
I board on my pda (cid locked)on the Spanish language HTC_304
sorry for my bad Englis
thank you in advance
My email: [email protected]
help me plaise
is that the bootloader command Herme (mtty) could walk on Advantage X7500
i had this problem and what i did to remedy it was, take out the battery, take out the sim card and the sdcard. replace the battery and turn on the device.
once it is in the bootloader plug in usb cable and make sure the bootloader shows usb at the bottom.
then try to load any rom that is for spl 3.0. they should load and get it out of the bootloader mode.
Once you have it working again then be sure and flash the proper spl of the rom that you are wanting before you flash the rom.
i tried the wrapper and hardspl as well until i just tried the above example on a whim and it worked. I hope it works for you.
CE
thank you for your answer
I board on my pda (cid locked)on the Spanish language HTC_304
Can you explain how you did
thanks
Was there any solution to this problem, I have the same problem?
is what you got the official rom spain

Categories

Resources