Database Users

official at&t callerID update bricked my phone.. :(

after my phone rebooted once the update was complete, it wont get passed the "at&T World Phone" white screen... SOMEONE PLEASE HELP ME!!!! i was using a stock at&t pure with the stock rom. i can not upgrade hardspl or ANYTHING any suggestions on how to get my phone to boot? hard-reset went through with no signs of failure but it still will not boot up after that finishes... sorry if its something im overlQQKing, but i just cant figure it out. n yes i have researched although obviously not enough at this point. Thanks to anyone who can help in advance. forgive my stupidity!!!

......
noone?????

The HTC Pure updates hosed my phone too, I had already applied hard-spl to my Pure and i've flashed it with dozens of roms. Since I was currently using one of the "Stock" AT&T roms posted on XDA I figured I could apply the updates. Unfortunately after applying the update my phone froze at the boot loader. I was forced to flash my rom using the memory card method and then restore a backup.
you could try putting the phone in SSPL mode manually, (reset button+volume down), the run hard-spl hard-spl in manual mode.
you can then flash your rom using the memory card method. (FAT32 formated memory card, rom file renamed to topaz.nbh copied to root of flash card, reset button+volume down to enter SSPL, power button to confirm flash).
All this assumes you've already tried to hard reset your Pure (reset button+vol up+vol down)

Thanks for the reply! Unfortunatly, i tried the manual method and after it hanging at 0% for about 5 minutes, i keep getting error [262] update error.. (communications error) is this becuase i can not sync with mobile device center (win7)? I really dont want to just have to toss the phone! I have had an at&t tilt, at&t fuze, and now the at&t pure, and this is the only phone i have had this problem with for some reason...

Try Unplugging Your Pure From the computer Take Out the Battery Put the Battery Back in Mean While Restart your computer and Press Power And Volume Down At the Same time on your Pure If its on the colored screen your good,..Make sure your system is online and your not downloading anything and plug in your Pure to the computer it give it about 2 minutes to download the HTC USB driver then once its done your phone will say USB on the bottom of the Red Green Blue And White four color screen Then open up one of your ROM's and Flash it,....Do You Have Windows Mobile Device Center Installed?
If Not here is the Link
http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
If you do already you need to uninstall the Driver update for windows mobile media center then install it again .

i can get the bootloader screen just fine! i just can not get hardspl to flash onto it. it sits at 0% every time. the phone will not boot so i can NOT get into mobile device center. The tri-colored screen comes up with no problem and it says USB on the bottom, so the drivers are already installed. I even tried hard-reset and still no luck

There was an additional cab file I needed to install to HSPL the Pure
"enablerapinew.cab"
basically the machine just would fail to load the HSPL without it
but it still functioned afterwards, does yours?
Do a search on XDA find and DL the cab (or I could attach a zipped copy)
If you can still access the device,
just copy enablerapinew.cab to any temp dir on the device
the execute it through fileexplorer
then go back to installing the HSPL (mine then worked fine)
If you haven't already, You should go to
http://forum.xda-developers.com/showthread.php?t=520312
you'll find troubleshooting info and a link to the extra cab there
If you really are bricked at this point , it sounds like nothing has actually
been changed on your device yet? its just frozen should be still under warrentee? Unless anyone else has a better suggestion you should be
able to return it for exchange to ATT
Good Luck
KJL

It sounds like Windows is not properly recognizing your device when it is plugged into the USB port while in SSPL mode.
Have you tried different ports?
Is there another computer you can use?

another thought about returning under warranty
on the boot page of the stock Pure it indicates HSPL 1.83.000
After you update the HSPL it will say HSPL "1.83.Olinex"
this normally an indication of a successful update,
but it will probably void your warranty if they just look at the boot screen
This is true for all Pure (and Tmobile Compact V) Rom upgrades
The Stock Pure came with 6.5 and therefore the 1.83.00 HSPL
The Diamond2s did not, so their solution which reverts to 1.63 <?>
will not correctly revert to 1.83.00 on the Pure.
No way to correct this yet as far as I know,?
All the "reverts" are geared toward the Diamond2s, not the Pure.
But If your boot screen indicates 1.83.00 before it freezes
I'm fairly sure its still entitled to a warranty repair/replace
How could they tell the cause of the failure
was a reburn as opposed to natural causes?
Good Luck
KJL

When you put the phone into a manual bootloader mode... Mobile Device Center becomes obsolete.
HardSPL is only needed for unofficial roms. Forget HardSPL for the time being. The goal here is to get your phone operational. Just download the official HTC WM6.5 WWE rom and flash that. Put phone in manual bootloader mode and run the Rom installer.
As long as your phone is in bootloader mode and says "USB"... then your set to go.
Another solution is to try another PC. You'd be surprised how often that will resolve your issues. Perhaps find an XP machine and install Activesync (so it loads the bootloader USB drivers). I had to do that on several occasions when my main PC refused to flash my mobile device.

I did both of the updates htc has for the pure. Both worked fine. I am on the origianal rom. It does reboot your phone and stays on the white screen for a min then it loads the update and the phone starts.

The offical ROM comes back with a wrong vender ID error I guess cause its a "pure" and not the HTC branded "topaz"... NOW what should i do??? Seems like i NEED hardspl so i can flash any ROM, as from what i researched, there IS NO AT&T Pure rom that has been released. I still cant figure out why a hard-reset will not work though.... This is REALLY starting to get me angry!!!

Just for reference, the Pure's ID is TOPA210 32M
SPL-1.83.0000
The official hotfixes worked fine for me as well. Did you apply the hotfixes on the original ROM that came with your Pure?
Also, does the official HTC Touch Diamond 2 ROM work for you? If so, the hotfixes for the Pure are irrelevant, as are any future updates released for the Pure. You should look for updates for the Touch Diamond 2 on the Worldwide HTC site.
If you needed to do a warranty claim, the closest you can get to returning your phone to stock/shipped form is to use the ROM dump using HardSPL and hope they don't notice that the SPL is different. Currently, there's no way to return the Pure back to completely official software.
A hard reset simply wipes everything off and restores everything back to what is contained in just the ROM you currently have on it. If you've flashed your phone at all, you've already wiped out the original ROM that came with it.

It is still the STOCK ROM. I have never flashed it yet.. The topaz rom will not flash due to a vender ID error. The spl is still stock also... i think thats is why i am having this problem. I bought the phone off craigslist so returning it to AT&T is NOT an option either way. My only solution is to find a fix. (or trash it) I really appreciate all of your suggestions and input so far. You guys are by far the best board around! I am a LONG time follower, but a few-time poster. Obviously i have little to contribute to the board.

Can I trouble you to dig up a few version numbers? It'd help evaluate your situation so we can see which options are best for your case.
ROM version? You can find this in Device Information. Start --> Settings --> System --> Device Information
Bootloader version? Do a soft reset while holding down the volume down button on the side until a screen with red, green, blue, and white, ordered top to bottom, shows up. It should be the second line starting with "SPL-..."

The ROM is the STOCK AT&T ROM (again...) I CAN NOT go to start;.... because if you noticed in the first post, the phone will not boot past the white "AT&T WorldPhone" screen... the spl is stock also incase you missed that part. (1.33.0000) I have never flashed the divice. EVERYTHING IS HOW AT&T SELLS THE PURE OUT OF THE BOX! NO MODS. NO FLASHED ROMS. NO HardSPL... NOTHING! STOCK!!! (for those overlooking the details in my previous posts) I have no doubt you guys (n hopefully a few girls ) will help me fix my issue. I'm just REALLY anxious for it to happen sooner than later!

Have you tried downloading the official rom here on xda and renaming it to TOPAIMG.nbh and update using the sd card method?
Here is the thread:
http://forum.xda-developers.com/showthread.php?t=600339
The download is in post #1

I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!

jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
You can flash hard SPL the same way by renaming the .nbh file to
TOPAIMG.nbh

jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
Actually that is supposed to be an officially signed rom. If that is true it will work with the stock spl. It will either work or it won't. Also, as stated in the response after yours, you can apply the hardspl via SD as well.

Flashing HD2 with WWE ROM

Hello,
I want to flash my device with 1.66.707.1 rom. I can't download it via HTC official page.
Now I have few questions. According to that I couldn't download it from HTC official page in my country because I've got inappropriate S/N. May I install it on my radio if I supply good (fake) S/N to official HTC page?
I even didn't tray to do this because I'm afraid I can turn my HD2 a into brick.
I don't care about language. I think that after flashing ROM I can download a proper language pack.
Greats.

invalid serial means your phone is vendor locked. (eg t mobile, vodafone or whatever)
even if you download using a different serial the upgrade will fail saying "vendor id mismatch" or something similar.
in theory you need to wait for your vendor to release the update, however in reality installing hspl will allow you to instal the update without getting the error.
go read the hspl threads.

Easy to sey .
It's my first Windows Mobile based phone. I've never installed rom, and yet a cooked one.
I've have some bugs about which I've read on this forum. Those are:
* lack of virtual keyboard while creating a new text message (or any app which need it)
* error while starting digital camera.
All of that disappear after soft reset. That's why I want to install the newest rom.
To not start a new thread is there any way to find out if the rom which I downloaded from HTC suits to my phone? S/N is correct. If I start RUU it will start flashing my device, yes?
Another question. Is it true that every HTC Leo has 576MB RAM but it is locked down?

read this then, it has all the info you need on flashing your phone...
http://forum.xda-developers.com/showthread.php?t=609477
once HSPL is installed you can download an official WWE ROM from this thread and run it as if it were an official ROM for your phone...
http://forum.xda-developers.com/showthread.php?t=623283

y0yster said:
Easy to sey .
It's my first Windows Mobile based phone. I've never installed rom, and yet a cooked one.
I've have some bugs about which I've read on this forum. Those are:
* lack of virtual keyboard while creating a new text message (or any app which need it)
* error while starting digital camera.
All of that disappear after soft reset. That's why I want to install the newest rom.
To not start a new thread is there any way to find out if the rom which I downloaded from HTC suits to my phone? S/N is correct. If I start RUU it will start flashing my device, yes?
Another question. Is it true that every HTC Leo has 576MB RAM but it is locked down?
Click to expand...
Click to collapse
As EddyOS stated, go read my flashing guide THOROUGHLY!!
1. Install HardSPL on your device (best done using WindowsXP or Windows7 32bit).
2. Download the Rom you require from the download site provided and flash using the instructions provided in my guide.
3. Enjoy your new phone
Once you have HardSPL on your phone it will be protected from bad flashes and you will be able to flash stock or custom roms or radios as and when you require. HardSPL is definitely reccommended as it has probably saved hundreds of phone from being turned into paperweights when flashing a bad rom or flashing incorrectly.
If you want to try a custom rom then I would definitely recommend the one in my signature but its totally upto you what you decide to put on your device.
With regards to the 576MB Ram it does seem that its actually accessible but only using the newer 2.02 Roms with specific Radios. This has been tested and verified. It wont be accessible on a 1.66 stock rom though.

Hello,
I tried to flash my device witch rom which is on htc official page.
When I was flashing something went wrong and on 24% upgrade have broken. I did what was write on the program but all the time I have 4 strips red, green, blue and white. Before I turn on the device I have sign of warning.
What I have to do now? Is my phone dead now?
Please answer as soon as you can.

y0yster said:
Hello,
I tried to flash my device witch rom which is on htc official page.
When I was flashing something went wrong and on 24% upgrade have broken. I did what was write on the program but all the time I have 4 strips red, green, blue and white. Before I turn on the device I have sign of warning.
What I have to do now? Is my phone dead now?
Please answer as soon as you can.
Click to expand...
Click to collapse
- What ROM were you trying to flash and what ROM version (and language) do you have on your device?
- Is your device Branded?
- Did you flash HSPL?
- Did you see a progress bar on screen when flashing, or just the colored bars?
- When you get to the tricolor-screen (bootloader) and you connect to your PC, does it say USB after a few seconds, or does it say Serial?
- What went wrong at 24%? Did you unplug the phone, did your system crash, or were you just being inpatient?
If you answer the above questions, someone may be able to help you. Also, start by reading the stickies.

Rom was 1.48.479.1 and I wanted to replace it with 1.48.479.1 because some bugs were annoying me which I mentioned earlier.
Yes my device is branded but it doesn't have simlock.
No I didn't used HSPL because I downloaded rom from HTC using my own original S/N.
When I was flashing I saw brogress bar with HTC logo.
I have those tri-colour screen when I power on the device, but before that I have warning triangle. No it doesn't say Serial nor USB.
What went wrong. I swear I don't know. No, no, no I wasn't impatient. After it hanged on 24% I got error message from the program on PC with UPGRADE ERROR. I've tried to resume like the program said me. But without any effect. What I did was unplug; put aut battery; wait 3 seconds; put battery in; power on and plug in. I'm sure that I was doing everything right because I was following the program.

help
samsamuel said:
invalid serial means your phone is vendor locked. (eg t mobile, vodafone or whatever)
even if you download using a different serial the upgrade will fail saying "vendor id mismatch" or something similar.
in theory you need to wait for your vendor to release the update, however in reality installing hspl will allow you to instal the update without getting the error.
go read the hspl th
hi there i really need help
i have a htc hd2 uk on t-mobile tried to rom update and messed it up , things dont work , i would like to ind software to rom update even htc.com s/n not right message comes up . please help
Click to expand...
Click to collapse

If i have 1.48 and with my serial can`t download 1.66... it is recommended to install WWE 1.66 with serials posted here without HSPL? my device is also WWE and was only sim locked Vodafone. (non-branded)

If you have questions regarding rom or hardspl flashing please ask in the correct thread.

if,when you put your serial into htc website, it doesn't allow you to download, then you MUST use hspl to flash an unbranded rom.
@y0ystet. your phone is branded. sim lock its not connected to vendor lock.instal hspl and try again, same rom.
@lakhbeer, did you flash hspl first? more detail please, messed up? doesn't work?
@rayman your phone is vodafone locked.
I repeat, the htc website doesn't accept your serial, you are provider locked and that is not connected to sim lock/unlock.

I sent an e-mail to HTC about that. They said I can send the phone to them.
I found sth out. If I hold the volume down and connect the usb cable I have a message on my screen. On screen which have three colours on green I have: "Upgrade Rom code error. Please try again" And on the white I have: "Serial".
Is there anything I can do about that?
But don't say me to flash witch the HSPL. I won't do that on two reasons:
I've never do that
If I send it to service I'll void my warranty.
What would you suggest to do?

I've solved the problem .

you going to let people know for future use?

How to fix ROM error on VODAFONE UK solution
I also have a HTC HD2 bought from Vodafone.
I flashed my mobile and installed Pandora 1.4 ROM...it was always freezing my Leo every time I looked at docs tab, so I decided to install shipped Leo ROM 1.66 and that is when things went wrong, same problem as you have now, so I downloaded h**p://w w w .4shared.com/file/205652004/1bf6c7ce/RUU_Leo_Vodafone_UK_1434051_Ra.html
aka the original ROM from Vodafone UK and it is working now....but now I am no sure if I wanna try more roms because next time I can be stuck with error screen forever.....

rom re boot steps

Hi XDA developer
I need help as my HTC HD2 MOBILE is not reboot I have tried the hard reboot and nothing happens.
two questions;
1. if i was to install a new verison of the rom Altermis v 26. which i have downloaded there is a another software called SSLD that I also need to download where is this. And how do i do this.
2. what happens if i cannot reboot the phone TOTALLY - in order to get to the operating screen where i can restore factory settings. I have also done a soft reset and still cannot getting into the phone.
THE MOBILE IS STUCK ON THE "HTC" PRE BOOT UP SCREEN AND NOT PROGRESSING FORWARD FROM THIS POINT.
HELP!!!!!!!!!!!!!!!!! PLEASE

keilah said:
THE MOBILE IS STUCK ON THE "HTC" PRE BOOT UP SCREEN AND NOT PROGRESSING FORWARD FROM THIS POINT.
Click to expand...
Click to collapse
did you flash a custom rom before this happened? If so, it is likely that you forgot to update to a compatible radi. Look through the thread for the rom you downloaded for details.

Hi
oK I under stand but if you was intsalling Altermis v26 on your phone.....there is a additional file where youy down load the software before transferring to your phone what is that software??????
please callled and where can i downlaod this

do you mean hspl? see my sig

yes
if that allows you to download "software" to the HTC HD2 device....and can you kindly please post the link here. and any steps i need to be aware off as i am new to this site.
Once again may thanks for all your feedback and assistance.....

the link is in my signature
"One HSPL3 to rule them all - all leo's supported, all spl inc tmous 2.10.0000"

[SOLVED] 2.1 Rooting issue & GSM Hero (White screen, green htc logo, stuck)

[Solved]
Hi there.
I got hold of this second hand phone.
I dont think its been modified in any way yet.
Last night the phone asked me about doing a update. So i did.
After the green progress bar completed i got to a white screen containing a green htc logo. And its stuck there in a loop.
So... I cant turn my device on... whyyyy? :'(
All i can do is to get into the standard htc recovery.
And into the hboot. Some place there it says:
HERO CVT SHIP S-ON
HBOOT-1.76.0007 (HERO10000)
MICROP-010f
TOUCH PANEL-SYN0104
RADIO-6.35.15.11
Aug 4 2009,19:43:30
I have done a wipe and a hard reset. Still it get this white screen on death. (WSOD) Im sodding of to bed...
You now know that it doesnt have a nandroid backup, and that I cant connect the phone via a usb connection to pc. And I dont have any custom recovery installed.
Ive tried to recover from a offical rom with a update.zip copied with a card reader onto the sd. Ive tried a few. The recovery see's the file. But when i try to install it it says "Verification failed Installation aborted"
Ive tried the recovery-RA-hero-v1.7.0.1.img, but without a usb I cant figure out how. Is there a way around for installing RA with just a sd card?
Please, does anyone have a good solution here.
Or some helpfull info to point me in the right way.
Sincererly,
Thor

See these threads similar,... Should be easy to sort.
http://forum.xda-developers.com/showthread.php?t=786938
and http://forum.xda-developers.com/showthread.php?t=787483

Good morning
Thanks, ive been looking at that.
My Win7 pc wouldnt show the ADB Interface in manage devices.
Only thing that pops up is a disk drive called HTC Android Phone USB Device, USB Mass Storage Device and a USB Composite Device.
Im gonna try this on my windows xp machine later today.
Hope it finds my phone, if not... what can i do?

So you need to update drivers as per the link in those threads,... Have you done that already pal?
Sent from my HTC Hero using XDA App

Hi again
Yes, I followed every step on that RUU driver guide on my win 7. But the drivers doesnt pop up as they should.
So I cant install the correct drivers since it doesnt show.

Halfway solution!
I got a breakthrough.
1. Remove the battery and replace it.
2. Hold volume down/up and tap power button. (htc enters hboot)
3. Taps back (enters fastboot)
4. Connects USB Cable (fastboot changes to fastboot usb)
5. Computer finds device My HTC.
Then i run this:
_HTC Hero_RUU_Hero_HTC_WWE_2.73.405.5_WWE_release_signed_NoDriver.exe
I got this from the htc pages. The software says i have ROM version 3.32.405.1
So i have a newer one installed then the one they have on web!?
I choose update on the software, now it tries to install 2.73.405.5
I got a half working usb connection now.
Fastboot restarted and changed to RUU USB.
Then i get a Error: 140 / 131 Bootloader version fail.
Can it be that the hard reset ive done messed up the bootloader version.
For me it looks like the phone is still in a new version ROM.
Anyone vise got anything to say about this?
Kind regards,
Thor

Aha,.... Ok, thats probs because the RUU you're using is older than the ROM already installed.
Try this one... RUU_Hero_HTC_WWE_3.32.405.1_R_Radio_63.18.55.06P_6 .35.15.11_release_signed.exe
That is the unbranded ROM,...

Wow
Suddenly everything klicked back into place!
Im past the white screen of death!
That RUU link was flawless for my device.
And the fastboot RUU USB installed everything.
Im back in business.
Much appericated m8

No problem. Now do us a favour and put [SOLVED] into your thread title. Thanks.

So...
Any suggestions on what i should do with it now?
Gotta root it i guess.
Then install recovery RA.
Any suggestions for a good rom to try?
Thanks again,
Thor

theres loads, but my suggestion would be villainrom 12 for a 2.1 sense rom, or froydvillain for a 2.2 rom

Ok
How do i know if i have a 2.1 sense rom or a 2.2 rom?
Or was that a dumb question from me, since you meant to install those?
Im kind of new, just left ye olde nokia behind

lol... Ok,... So you used the 3.32 RUU yeah? That is stock 2.1. If you used the other one, that is 1.5. Use BTDAGs guide in my sig to find out how to flash custom ROMs.
I also recommend Villain 12 for 2.1,... Or Froyd for 2.2. Depends if you like the SenseUI or not. Take a look at both in the Dev section.

Ok
Yes, I definitly want to have the Sense UI.
So then i wanna try out installing a villainrom 12 on a 2.1 sense rom.
Settings - Software Information now says:
Firmware version: 2.1-update1
Baseband version: 63.18.55.06PU_6.35.15.11
Kernel version: 2.6.29-063c4d24 [email protected] #1
Build number: 3.32.405.1 CL191507 release-keys
Software number: 3.32.405.1
This is what i have on it now.
I tried doing the phone software update again, when it asked me again.
Got the same error. So I did the usb install over again. All ok again.
Note: The update it tries out is 3.32.405.2 (5.87MB)
So... can i follow BTDAG's guide from here?
Or do i have to downgrade or update something first?
Guess i have to choose Superuser for Android 2.0~2.2 when i do the rooting with androot.
I got a problem in that guide when typing su in the terminal window.
I didnt get the "Super User Request Prompt" as it told about.
Ive now tried terminal from both usb and the terminal emulator.
WHen i try to do the SU or the flash_image recovery command i get permission denied!?
Without su rights i can do the flash_image recovery /sdcard/recovery.img command, since i need the su permissions.
Thanks again,
Thor

Hi again
I cant seem to get the SU rights i need.
Ive used universal nandroid for the rooting! (it tells its now ok)
But i cant flash in the custom recovery image.
Ive now tried a different approach:
1. Installing the ROM Manager and trying out ClockworkMod recovery(its installs ok)
2. Then I boot into recovery by holding the home(house) and power on, I get the white screen of htc death again and it goes into a black screen with a red triangle and a ! on it.
3. Then I release home and power on.
4. Presses down volume up and taps power on.
5. The hero boots into the standard recovery!?
(I think the way im starting up, are reflashing the recovery. am i right?)
Clockwork also have a "flash RA 1.7 recovery" option, ive tried that one too.
But with the same result...
Any one know about this?
Best regards,
Thor Elvin

Solution for life!
After a lot of surfing i found it!
This great tut worked for my device:
http://www.villainrom.co.uk/forum/s...o-Root-The-2.1-RUU-or-OTA-Update-For-The-Hero
I got a blue carebear in the background, and im making a big grin!
Now im rooted and backed up.
Great thanks to Pulser for a great tut.
Edit: VillainROM12 installed 1
PEACE Y'ALL!!!

QUOTE=thorelvin;8284640]After a lot of surfing i found it!
This great tut worked for my device:
Pulser did...
I got a blue carebear in the background, and im making a big grin!
Now im rooted and backed up.
Edit: VillainROM12 installed 1
PEACE Y'ALL!!![/QUOTE]
Dude, nice that you got sorted. I have kids so Carebears are good to have around. Respect to Carebears, and at the same time it would be cool and revisit the forum and thank Pulser, else thank him here as Pulser_g2 (i think). He sort of wrote, reworked the tut originally from the cdma version here. Sorted me too going 2.1 to 2.2. I had shedloads of fun with roms in between but its only thanks to him.
I guess this could be classed as one of those "Circle of life" philosophy budhist type **** things cuz the answer was really where you started, but for me... its all about takin care of the Carebears....
For the record his contract ends around May so get your Hero fix requests in early...!
Soz Pulser... And massive thanks for the opening to a new dimension for my hero...

[Q] Help Stuck At Bootloader!!!

So I was installing a stock rom on my device so I could return it to tmobile, but i think i may have installed the wrong type of rom. Its showing I have spl-3.03.0000 XE, and it gives me this error that states "upgrade ROM code error Please Try Again" and when I try another stock rom it gives me an error that states "wrong vendor ID" is there any way to fix this and install a stock rom once again?

The ROM you flashed, where did you download it from? If it was not from the T–Mobile website I suvvest you go download the official upgrade ROM from there, when it ask for hour IMEI number you can vet it from under battery.

T-Macgnolia said:
The ROM you flashed, where did you download it from? If it was not from the T–Mobile website I suvvest you go download the official upgrade ROM from there, when it ask for hour IMEI number you can vet it from under battery.
Click to expand...
Click to collapse
Tried installing the update off of tmobile the installation stays stuck at zero percent and the installation times out. Thanks though! Is there anything else i could do? Any help is much appreciated!!

For the sake of testing... Put hardSPL and try a custom rom to see if it boots
Sent from my HD2 using XDA Windows Phone 7 App

edwards33 said:
Tried installing the update off of tmobile the installation stays stuck at zero percent and the installation times out. Thanks though! Is there anything else i could do? Any help is much appreciated!!
Click to expand...
Click to collapse
Ok from the title of your thread here I am assuming you are puttng you HD2 into bootloader, waiting for USB in the white bar of bootloader and then flash the ROM? If you are doing this try right clicking on the RUU and select run as administrator. If that does not work try flashing it via SD card. Go to this thread to learn how to flash via SD card.

Its showing I have spl-3.03.0000 XE, and it gives me this error that states "upgrade ROM code error Please Try Again" and when I try another stock rom it gives me an error that states "wrong vendor ID" is there any way to fix this and install a stock rom once again?
Click to expand...
Click to collapse
This happens when you have hspl installed and then flash a 3.14 stock rom over sd card.
Hspl gets removed, replaced by 3.03.0000, the flash tries to continue but cant.
The first and biggest question is..... you say it's from t mobile., but what colour are the send and end keys? White? Or red and green? Since to get the error you get implies an incorrect stock rom, and incorrect stock roms kill tmous phones.please also include the complete filename of the stock roms you have tried, especially the first one that gave rom code error.

Try creating a gold card. It will force you through to flashing off the SD card. I also can JTAG this and resolve the problem for you as long as there is not physical nand-failure.

T-Macgnolia said:
Ok from the title of your thread here I am assuming you are puttng you HD2 into bootloader, waiting for USB in the white bar of bootloader and then flash the ROM? If you are doing this try right clicking on the RUU and select run as administrator. If that does not work try flashing it via SD card. Go to this thread to learn how to flash via SD card.
Click to expand...
Click to collapse
OK Tried running the tmobile official update throught the sdcard as well still no luck It just says loading and nothin happens after that.
Also tried installing HSPL but says it can not be flashed
samsamuel said:
The first and biggest question is..... you say it's from t mobile., but what colour are the send and end keys? White? Or red and green? Since to get the error you get implies an incorrect stock rom, and incorrect stock roms kill tmous phones.please also include the complete filename of the stock roms you have tried, especially the first one that gave rom code error.
Click to expand...
Click to collapse
the send and end keys are green and red.... the stock rom that gave me the error is ruu_leo_s_tmo_de_3.14.111.1_radio_15.42.50.11u_2.15.50.14_leo_s_ship
Also have tried Installing The tmobile update directly from tmobile.com T-Mobile_HD2_MR_Software_3.14.531.1

OK I was able to get the phone to boot up by using a test rom but it still will not load up a stock rom it won't work through ruu or from sd card the spl also changed to 2.00.100 XE is there anything else i can try? thanx for the help!

Ahh see now that's a shame.
you do have a tmous, but the rom tmo_de IS NOT for your phone.
That's about as close to bricking your phone as you can get without actually bricking it.
that rom is tmo Germany, which means it is for the regular hd2. The ONLY stock roms your phone will accept are tmous stock roms. All other t mo roms from around the world are for regular hd2.
And now you made it worse by flashing a test rom with an spl which is a pain to get rid of.
In the test and stock roms thread where you found that test rom, DO NOT flash the first rom in the list, it will kill your phone.look at the end of the list and there is a version of hspl edited to work with spl 2.00
Give that a try first.
You aren't the first so Google stuck on spl 2.00.1000 and start reading.
DO NOT FLASH ANYTHING TILL YOU ARE 100% SURE OF THE EXPECTED OUTCOME.
You got real lucky, there are countless threads here that go "tmous,non tmous stock rom, phone now utterly dead",,, don't ruin it now by going flash crazy.

edwards33 said:
OK I was able to get the phone to boot up by using a test rom but it still will not load up a stock rom it won't work through ruu or from sd card the spl also changed to 2.00.100 XE is there anything else i can try? thanx for the help!
Click to expand...
Click to collapse
You need to go to the "Leo 1.5 T-Mobile Test & Stock ROMs" thread anf use the link at the bottom of post one named " HSPL with MFG SPL 2.00 support!". This is suppose to support the SPL version you have and allow you to flash HSPL to your HD2 wich should allow you to flash the official T-Mobile ROM or any custom ROM you want to flash. Good luck
Edit: You beat me to the punch Sam
Also the first stock ROM must have changed your SPL and that must have been why you could not flash the official T-Mobile ROM. Like Sam said you got very lucky, if that first stock ROM would have flashed hou would have had a bricked HD2.

OK well tried using the hspl3 but still get the error saying bad spl so I'm gunna start reading up and hope there's a way to get the stock rom back on the phone. Thanks everyone for all your help its greatly appreciated!!
Sent from my LG-G2X using XDA Premium App

You do mean the specially adapted hspl from the teststock roms thread right? Not just normal hspl3?
If so, next step should probably be goldcard.

samsamuel said:
You do mean the specially adapted hspl from the teststock roms thread right? Not just normal hspl3?
If so, next step should probably be goldcard.
Click to expand...
Click to collapse
Yea it was the one from the stock rom thread I'll read up and learn to use gold card thanks
Sent from my LG-G2X using XDA Premium App