need help i900 problem!!! - Windows Mobile Development and Hacking General

hello sir
i have big problem
my i900 power on but no network, always show cross to tower
[i think not detect sim].
and if i want to see imei it show "the phone is currently off.would you like to turn on the phone?"
then option yes/no but if i press yes not happean any thing.
if i try to reset phone by setting>system>hard reset> there is 2 memory
1>main memory ( reset tap is enable)
2>my storage (not enable reset tap)
if i try main memory reset it need password 1234 i enter 1234 then it show this error "when phone is turned off,you cannot hard reset.turn phone on,and try again"
key combined hard reset not work. soft reset work but same.
please ! please !! please !!! need help.
how to revive this phone normolly???

Did you mess around with radio rom (phone.bin)?
Try to reflash it with COMPLETE (phone,pda and csc) new ROM, official
if possible.
You said:
"key combined hard reset not work."
That part of device function (battery charging also) is controlled by phone
part of ROM (phone.bin), so, it seems that problem is caused by faulty phone.bin.
Reflash it!

rtomakov said:
Did you mess around with radio rom (phone.bin)?
Try to reflash it with COMPLETE (phone,pda and csc) new ROM, official
if possible.
You said:
"key combined hard reset not work."
That part of device function (battery charging also) is controlled by phone
part of ROM (phone.bin), so, it seems that problem is caused by faulty phone.bin.
Reflash it!
Click to expand...
Click to collapse
thank you for reply but i am new about this.
can you give me COMPLETE (phone,pda and csc) new ROM, official ???
and how to ???
thanks.

Look here fore official ROMS:
http://www.samsungmobile.com/support/omnia/index.jsp
Manuals about flashing omnia (good ones) you should search on modaco
web site. They have very good omnia support.
Short version: install activesync, all drivers for omnia and run .exe of firmware update from PC.

install active sync 4-5,
install modem driver.
restart pc
but it hang on this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i use on xp[32 bit]
how to solved??

Related

HELP! Problematic WM6 rom load. Phone inoperative

Hi everybody. I'll try to brief 2 days of an unsucessful rescue operation. I have a XV6700 by Verizon, Tried to flash the WM6 Verizon rom first. My BL version was 2.05, so I had to downgrade to the 2.02. I followed step by step on some guy's post on PPCgeeks. the operation got messed up somewhere in the middle and my nightmare started right there. When flashing the NOID rom to the phone, it gave me an error and now it won't take back the OEM AKU 3.3, it says, WRONG DEVICE, this application is not made for your device. So I forgot about the OEM, tried to COOK a custom rom using kitchen, the only one that the phone will accept is the one with RUU - NO ID and Carrier Generic or Verizon, the ROM flashing process starts at STEP 3! it doesnt do radio upgrade , it starts right on "Upgrading CE..." and at 99% it fails. the phone then, boot ( weird boot screen, pixels, colors, lines ) followed by a blank ( white ) splash screen. and thats it. So i managed to find a GENERIC version of the WM6 already compiled. That one gives me the same error, error 112 ( see picture ) at 99% and boots with the same weird boot screen, blank splash, but this time it does show partial WM6, i can access programs, answer call, messaging etc. but it shows overlapping fonts, and the Dialer is tottaly blank. I tried installing more than 10 different dialers, but the phone screen is blank. Now I need help. I am afraid to make it worst. what could be wrong? My BL shows 2.02 .... but using the mytty software and punching task 28 55a ( as explained on the downgrade procedure ) it doesnt show what it's suppose to show. Heeeeelp!! Thanks
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

HTC hero bricked .help.....

I bought my HERO just a few days ago.
Once,the system halted and I took the battery out of the phone.
After that,when I turn on the phone,it show the first picture in the attachments
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and then only when I press the DIAL button ,the phone responses,and it shows the second picture in the attachments
I have checked that the buttons of the phone are all OK.
And I have sent it to someone to mend it,he said that the phone can not be connected to the computer,but he succeeded in flashing it with the miniSD memory card. BUT the phone still has the same problem.What's more ,the H-BOOT has been flashed by him from 1.76.005 to 1.76.007. But the problem still
exist....
Can anybody help me?...
And I'm from China,my English is not very good...
This might help...
g0mib0y said:
EDIT: DON'T UPDATE TO 2.1 AGAIN SINCE IT WILL HANG ONE MORE TIME. WAIT FOR HTC TO RESOLVE THIS ISSUE!!!!!!
EDIT 2: BACK UPP ALL YOUR DATA FROM YOUR MEMORY CARD FIRST!!!
EDIT 3: How did I find this out? I talked to a very helpful HTC suport rep (yes they do actually exist in Sweden). He helped me do these steps and so I thought I should share this.
Ok so you got a message that 2.1 was available for your Hero - FINELY! and you installed it using OTA. And then you got a triangle with a ! in it and you rebooted and all it says is "HERO".
This is how to solve it!
Take out your memory card. FORMAT TO <span style="font-weight:bold;">FAT32</span>!!!
Download the RUU 2.73.405.5 from HTC support homepage
Run the installation.
When it fails to find your phone <span style="font-weight:bold;">DON'T EXIT!!!</span>
If you are using Windows 7 go in to c:\Users\<span style="font-style:italic;">yourusername</span>\AppData\Local\Temp
Search for ROM.zip
Move to desktop
Rename to HEROIMG.zip
Transfer to your newly formated memory card now with FAT32 file system
Put memory card into phone
Start phone holding volume down pressed.
It will now check zip fil and then ask if you want to install.
homekey for YES
After installing you have 1.5 again and can safely upgrade to 2.1 OTA
Click to expand...
Click to collapse

HTC surround enter usb host mode after unlock by XTC clip

HTC surround T8788 AT&T enter usb host mode after unlock by XTC clip.please help me.Thanks.
Just reflash your phone.
eglunas said:
Just reflash your phone.
Click to expand...
Click to collapse
i flash RUU_Surround_TELUS_WWE_1.04.661.00_Radio_5.51.09.29_22.32.50.10U_by_ansar
but error 294 : invalid vender ID.i need rom at&T please help.
Here is the At&t ROM its the original 7.7004
http://www.megaupload.com/?d=KY9UZEHI
(Charge Battery to 100%)
With the phone powered off hold volume down and power button to boot into Bootloader screen (Red Blu Green White),plug in usb cable to computer and into the phone(it will say "serial" at the bottom ( let it install the qualcomm cdma driver) Then "serial" will change to "USB" at the bottom of the phone screen, extract the ROM.zip file from download link above and click the Rom update utility EXE and follow the instructions from there.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Ok I need you help please, I have the same problem with my htc 7 surround of AT&T, but I didn´t use the tool "unlock by XTC clip". My phone worked well, but the last week, it freezing in the logo "HTC" and don´t pass from here; it do not start wp7.
I use this tool that you give from megaupload but when the program verify the image version of my htc - it is in blank, my phone phone don´t have image version- I don´t know what I have to do. I use everything to install a new windows phone 7 operating system to my htc surround.
please give me a response...
i need this file but link not working again. says file might have been deleted
waiting for your response.
I need this file but link not working again. Thanks in Advance... Kamijee
deleted

[Q] Pattern Lock on 2nd hand Flipout?

Hi all,
I bit the bullet and picked up a 2nd hand OrangeUK Flipout (details available if I need to prove I bought it legally)... but the seller cannot remember the pattern to draw to access the phone.
How might I resolve this issue, please?
I can access the Bootloader, which is on v91.10, but that's all I've found so far.
I have found RSD Lite v5.6 and the USB Drivers from the MotoDev website.
Will flashing RUTEM_U3_01.19.2 (or any other RUTEM) onto the device ie following the Debranding Guide, reset this and allow me to start playing with Android?
What about the FlipOut Recovery?
Thank-you,
Dylan.
Wow. Err, okay, I wasn't expecting it to be that easy.
It only took a simple Hard Reset and it's fine - Back to the start as if seting up a brand new out-the-box phone!
In case any other fellow Noobie-Noobs encounters this issue, here's what I did:
Motorola Flipout (MB511) - Step by step hard reset
1/. Switch the device off - Hold the power button for a couple of seconds and then press Power Off
2/. With the device off, open it up, hold the X key and hold down the Power button until you see the Motorola M.
3/. Shortly after, an image like this will appear:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4/. TAP the power button to enter the Android System Recovery menu.
5/. Use the little D-Pad to select the 4th option - Wipe Data/Factory Reset.
6/. Press Enter to confirm.
7/. Confirm you want to reset the device.
8/. After the reset, go back into the System Recovery menu and select the 1st option - Reboot.
You should now have one factory-fresh phone!
Gratefully translated from Portuguese instructions at the EIL forum!

A way to unlock hardbricked Meizu Pro 5 ?

Hi,
I've hard bricked my Pro 5. No recovery access, no boot to rom, locked bootloader. After many search i see this : https://forum.xda-developers.com/meizu-pro-5/how-to/meizu-customer-service-flash-tools-save-t3447678, but this is bull-****.
I test many manipulations to get something on my phone other than "Bootloader, Locked".
So i dicovered this : Press and holp Vol + and Vol - and press one time power button. We get this :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After research about this, we get this :
http://forum.gsmhosting.com/vbb/f777/galexy-s6-exynos-7420-dead-1975230/#post12369382
And this :
http://www.mediafire.com/file/9qmezaezy1fyzrr/Galaxy_S6_Boot_recovery.pptx
Possible way to unlock hardbricked Pro 5 ?
Same way exist for Qualcomm Processor : http://www.androidbrick.com/unbrick...-have-the-right-kind-of-rom-qhsusb_dload_edl/
Subscribed, i do also have a spare "bricked" device
same problem here bro.tried everything..only mode available is fastboot and locked bootloader.in pc device manager i get unknown android 1.going to investigate the problem futher more.pls keep us in touch.tnx
barbonee said:
same problem here bro.tried everything..only mode available is fastboot and locked bootloader.in pc device manager i get unknown android 1.going to investigate the problem futher more.pls keep us in touch.tnx
Click to expand...
Click to collapse
Hey there. Got the same problem. Tried everything. Nothing happens. Have you got your problem solved yet?
The same problem
Sent from my PRO 5 using Tapatalk
Only way to solve this is taking the phone to technical service. Done it myself. Be careful tought, they will try to make you change the entire mother board (280€), but if you insist they will "find a way" to install the correct software in your phone and leave it as if it was new
it is possible to recovery via dongle ... but sn and imei can be lost
Try this thread.
https://forum.xda-developers.com/me...hard-bricked-lost-t3838461/page2#post79752427
Try this thread; it worked perfectly for me.

Categories

Resources