Related
Hi people,
I have a mayor problem. I just fu*ked up my phone by installing WM6.
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me!
s200 off
and I have this problem. my phone is off by installing new spl
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me
To go in the boot loader screen you have to:
press & hold camera and commmanager button
press the softreset hole
release the commmanager button and keep hold the camera button until the 3 colours display appear
Byez
but wat can i do after i hav the 3 colour screen come out?
pls help..... i'm very nervous..... i don wanna waste my money coz i screw up my phone.,...
i'm now outstation... can go back to the service center within this 6 mth....
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
mrsurya2000 said:
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
Click to expand...
Click to collapse
Which rom upgrade software ?
de.schurk said:
Which rom upgrade software ?
Click to expand...
Click to collapse
http://www.romupdate.ru/ghjibdrblkz...rophet_220734_2207114_024721_QtekWWE_Ship.exe --> this software
don't worry, your device isn't bricked as long as you can run it in bootloader
check in WIKI if you have G3 or G4 Prophet
I'm the exact same situation.
And wiki didn't help so far...
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
namco said:
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
Click to expand...
Click to collapse
Bear with me on the dumb questions
It looks like I managed to re-install
Thank you for your help. I installed the rom dezzer advised (post 7 of this thread) and it worked fine. Does that mean tha NOW i can flash smart1 1.3's?
Yep. Turn off the phone, make it sync with activesync and run UPDATE_ROM.bat.
Then cross your fingers Kidding. It will surely work. Remember to hard-reset after the upgrade.
If anything goes wrong just reflash WM5 and hard-reset. Always hard-reset after ANY OS upgrade.
Hi,
Is there anyone out there with their Polaris trapped in Tri-colour (and not running a .Olipro/.OliNex SPL). if so, PM me.
Me
Olipro said:
Hi,
Is there anyone out there with their Polaris trapped in Tri-colour (and not running a .Olipro/.OliNex SPL). if so, PM me.
Click to expand...
Click to collapse
Program stopped in percent screen (in 0%) and don´t run more. After if you unplugged the PDA (an HTC Polaris, of course) and swich on don´t pass of the Tri Color screen and you can read "POLARIS. SPL-1.25.0000.CPLD-2" and in the rigth corner "RUUNBH" but nothing began, no OS or programs, nothing... Any suggestions and help??? Thank You.
Can't flash SPL, Polaris FRA ROM; was bricked...solved,can't flash
Hi Olipro,
last week-end I tried flashing hard SPL v2 on my French Polaris, before planning to flash the new radio 1.64, then bepe's 0.66 ROM.
I spent the first part of Saturday night trying numerous times, recovering, taking battery away, and trying agin - never worked. Then I tried flashing the 1.64 radio, it went up to 99%, then stopped, error message: from then on my Polaris went to boot-loader only, after soft reset or even hard resets. Until dawn I tried to fix this (I'm not a developper, I'm a power user travelling 4 days a week by plane accross Europe). Couldn't fix it.
On Sunday I called a friend of mine who imports HTC and sells the channel: I gave him my Polaris and he took it with him to fix it. Result was very surprising: I had given him your hard SPL v2, and a few nice ROM's from this site, specailly bepe's, as well as all the radio versions listed here for POlaris; well none of all that worked with him, and he could only reflash the official ROM and radio, and return it back to me...(which was very kind as it took him some time).
BUT, overall I'm very frustrated as I'm an early adopter, and I would so much like to try cooked ROM's on this fabulous device.
What do you think I should do? Any idea?
Is there a way to guide me though a custom process or is there a real issue on ALL French ROM's out there? (can't believe that).
Your inputs would really be appreciated.
Thx many, HangLoose.
23:45 > it finally worked !! (I must have been doing something wrong previously, sorry for bothering Olipro).
And thx for enabling us to use best in class cooked ROM's from this site.
I'll be loading bepe 0.67 just now. !!
Regards, HangLoose59
My cruiser not leaving the screen tricolor
My cruiser not leaving the screen tricolor, Tried to replace the original language (Spanish) by the English and upgrade stopped in 14%, dai then not leaving the screen tricolor.
Some hint.
v1zca1n0 said:
Program stopped in percent screen (in 0%) and don´t run more. After if you unplugged the PDA (an HTC Polaris, of course) and swich on don´t pass of the Tri Color screen and you can read "POLARIS. SPL-1.25.0000.CPLD-2" and in the rigth corner "RUUNBH" but nothing began, no OS or programs, nothing... Any suggestions and help??? Thank You.
Click to expand...
Click to collapse
FIXED! at last the problem was I used a SPL for HTC ELF not Polaris and, I don´t know why, that makes OS stopped in an eternal bug... Whem I use again the same Hard SPL for Elf Voilá! Do it! And know all works fine. I promisse: I will never change the BootSplash be sure
v1zca1n0 said:
FIXED! at last the problem was I used a SPL for HTC ELF not Polaris and, I don´t know why, that makes OS stopped in an eternal bug... Whem I use again the same Hard SPL for Elf Voilá! Do it! And know all works fine. I promisse: I will never change the BootSplash be sure
Click to expand...
Click to collapse
I have the same problem My Pc has scrached and now my polaris is blocked to the bootloader
Is some could you help us ?
Diagorn said:
I have the same problem My Pc has scrached and now my polaris is blocked to the bootloader
Is some could you help us ?
Click to expand...
Click to collapse
Hard reset the device and it can take u out of bootloaer mode. To hard reset:
GPS/MESSAGING and INTERNET EXPLORER buttons, and at the same time, use the stylus to press the RESET button at the bottom of your device.
2. Release the RESET button, but continue pressing the GPS/MESSAGING and INTERNET EXPLORER buttons until you see a message on the screen
Release the buttons, and then press SEND on your device to perform the hard reset, or press any other button to cancel the reset.
Hello thanks for your help but I have already tried this
Diagorn said:
Hello thanks for your help but I have already tried this
Click to expand...
Click to collapse
Try with this program do a Hard SPL and tell me how gone
the Elf is a DiskOnChip device, the Polaris is plain NAND.
you can try it, but frankly, I think it's not really the smartest move
Olipro said:
the Elf is a DiskOnChip device, the Polaris is plain NAND.
you can try it, but frankly, I think it's not really the smartest move
Click to expand...
Click to collapse
You are rigth Olipro as always, but I left because I have the experience of used badly and block the PDA until I use again and unblock the machine. Maybe the diferent chip make a kind of bug than only can be fixed with Elf Hard SPL I don´t know but with me works. Let see if is the same with Diagorn
could be a side-effect, but the file should be blocked from flashing anyway.
i have the problem too. waiting for the solusion
Olipro said:
could be a side-effect, but the file should be blocked from flashing anyway.
Click to expand...
Click to collapse
Curiously Elf SPL unblock the flash and I don´t know why Anyway I stopped flashing anymore because I don´t want have the same problem again. Only I explain what happend to anyone that can have the same problem and attach the Elf Hard SPL if they want use and probe
BT Problem
The BT LED styed ON and after hardware reset (removing the battery, the reset button wasn't working) only the bootloader screen. It revived after I flashed the Radio ROM. And what bugs me is that BT button remains ON in TouchCommander, but NO BT. any ideas???
BT Problem
After synchronising with the PC i noticed the BT LED goes OFF ...
BTW
HardSPLv2.2
ROM 1.28Aserg.1WWE
RADIO 1.64.08.21
Cruise stuck in 3-color screen
Hi,
My Cruise just frooze, during GPRS synch with Exchange server. Soft reset and hard reset do not work anymore. If I take out the battery, and then switch on the device it stops in the 3-color screen. BT light stays on.
I have not made any changes to my Cruise, only added a 8 Gb SD card.
v1zca1n0 said:
Program stopped in percent screen (in 0%) and don´t run more. After if you unplugged the PDA (an HTC Polaris, of course) and swich on don´t pass of the Tri Color screen and you can read "POLARIS. SPL-1.25.0000.CPLD-2" and in the rigth corner "RUUNBH" but nothing began, no OS or programs, nothing... Any suggestions and help??? Thank You.
Click to expand...
Click to collapse
me too...somebody help !!! sorry my english
Strangely enough it works!!!
v1zca1n0 said:
Try with this program do a Hard SPL and tell me how gone
Click to expand...
Click to collapse
I was really frightened when my TC got stuck in Tri-Colour screen. MY Polaris came to standstill, trapped in.
Over and over ROMUpdateUtility.exe shows ERROR [262 or 284]: UPDATE ERROR while trying update.
And only this strange RUU gave me other ERROR [296]: UPGRADE ONLY that helped me to quite out the three-color screen and installed new radio successfully.
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
hard reset
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
do hard reset
i had done hard reset also
Try to bootup without the SD card (and may be SIM), I had this problem with my Vox, the SD Card was corrupted. After formatting the SD Card, everythig became normal.
Best of Luck
Same problem
Jeet8626 said:
Dear Please help my PDA HTC p3400 has hanged at started up only at front screen only it is not moving further. i had done hard restet also then also not working. Please help me out .
Waitng for reply.
Click to expand...
Click to collapse
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says Setup complete, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos (from Portugal)
matosmatos said:
Hi!
i have the same problemwith my P3400
i have made the upgrade to wm5 to wm6.1
the pda at the first time has booted and i have configured the regional time and the pen alignment until the the screen that says congratulations, click to proceed (or something like this).
After this, it gets stuck on the windows mobile 6.1 boot screen
i have made the re-update with the same rom update.
the problem persists!
I have made with/without sd card and sim.
Now when it boots apears
ONBL 1.07.0000
SPL 1010.olip
GSM 02.84.90
OS 1.17.0.0
then changes for the wm6.1 boot screen
and stucks here
S/n-SZ716FW06338
XT01
GENE 100 (old gene i think)
please help me
thanks in advance
Pedro Matos
Click to expand...
Click to collapse
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!
i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks
for ur info @matosmatos
hi
as per the numbers quoted by u urs is a old gene so falsh roms for old gene only this is just for ur info
goodluck
matosmatos said:
i have done it!
Now i have the wm6.1
i found another rom update! (coooollll!!!!)
heheehehehhe
thanks anyway!
Click to expand...
Click to collapse
@smb_do
hi
assuming ur phone is just dead ie just blank screen do this
1.power off the phone remove batter and press the power button 3 secs
2.put batter back in to the phone
3.Press camera button and then power on at the same time u will get tricolor
used usb and Flash new ROM
or press camera button and do soft reset using stylus this will also give u the tricolor use USB and flash new ROM
goodluck
smb_do said:
i have the same proplem you had can you tell me how you done it with new rom espiecly i cant flash room and i cant do anything
thanks
Click to expand...
Click to collapse
thasnffffffffff
Im so so saaaad
I try avery thing hard reset , now roms every time it accept the now rom and whine it restsrts again tha same problem it stop at
ONPL 1.07.0000
SPL 1.07.oref
GSM 02.79.90
OS 1.9.1.1
please help me send me at
ahmedrefaat82/hotmaill.com
gene hanges at start up page onyl (after rom Upgade)
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs
satishgosavi said:
I am also facing the same problem. I have old Gene. I had upgaded it to
Pro User's ROM WM 6.1 Sumit
Everything was running fine till I soft reseted the device. On soft reset it stucks at the start up screen
On boot it shows following
ONBL 1.07.0000
SPL 1010.olip
GSM 02.79.90
OS 1.17.0.0
Then it shows the windows animations and then it hangs.
This has happned to me twice.
I had installed following applications after the ROM upgrade. Does any application creating a problem
1) HTC Home (6 tab plugin)
2) S2U2,S2P,S2V
3) Quick Menu
4) Opera Mini
5) TCPMP with many codecs
Click to expand...
Click to collapse
Not likely, try a hard reset and see if your issue is solved
Addicted2xda said:
Not likely, try a hard reset and see if your issue is solved
Click to expand...
Click to collapse
I had tried that also but not able to recover I had to burn the ROM again .
I am scared now to soft reset my gene. Never know when it will get hanged again. (pls note that it does not hang on every soft reset).
I liked the new ROM (6.1 pro Sumeet) so much. It is fast and have left enough room to add/execute other applications. I have read so many good comments about the ROM. I do not want to change it to any other version.
Please.. please try to get some solution.
Thanks in advance.
regards
Satish
It Worked
Thanxxxxxxxx
Hello guys,
First of all I'm sorry for creating separated thread with problems, but i want to post them clearly and in one place. I hope that you can help with this, cause I'm trying and trying with many many ways, and nothing works for me . So lets start:
I have succesfully installed Windows XP on my machine. It works perfect.
But there are some problems ofcourse
First of all, the snapvue (I've installed liberated ROM) won't run. Nothing works. There is only black screen and 3G led is blinking. The only way I can run snapvue is to drain battery to 0%, and then plug the adaptor and wait a second. And the only time, that snapcue is starting - its when bios saying that i have 2% battery and it will close in... etc etc. Anyway, for some reason its hanging up after a while. So again - its not working.
I've tried the comonex way many many times with no success. There is only black screen all the time.
And now: I've tried it today again, and when I'm starting mtty, there is no USB anymore.
I've done it before, so please, don't tell me, that I'm not following the instructions .
I don't know what to do. Because of that - there is no sound in Windows, and anyway i need SnapVue side to run some 3G modem .
Now the OS side:
Wlan won't work. When I'm trying to install the driver it says: "Error 10, device can't start" or something like this.
I've tried all the solutions provided here without success. What should i do, and what I'm doing wrong?
Thanks.
Cheers,
Chris
SnapVue Side
Did you Hard reseted your snap vue ?
tryed to install HardSPL ?
What about taking out the battery and replug it (dont fire os only snapvue)
Is it working then ?
greets
kristoff_sz said:
First of all, the snapvue (I've installed liberated ROM) won't run. Nothing works. There is only black screen and 3G led is blinking. The only way I can run snapvue is to drain battery to 0%, and then plug the adaptor and wait a second. And the only time, that snapcue is starting - its when bios saying that i have 2% battery and it will close in... etc etc. Anyway, for some reason its hanging up after a while. So again - its not working.
Click to expand...
Click to collapse
Hello, for this.. I will keep on cmonex things.
First : are you able to use ECShift.exe ? if yes... try "ECShift.exe -gm" (without quotes) to see if it works (first) and what is the value (0 or 1). If it is 1, you are in the bootloader and need to go out of this using "ECShift.exe -mode0" and then soft-reset snapvue with "ECShift.exe -reset".
You might say that you already do that... maybe yeah. but you need to see exactly why it is black, is it black because of stopping to display, or because it enters bootloaders.... etc..
Second : if you get access to WM, go to the snapvue settings button (if you still have the snapvue today plugin) and go to power -> advanced .. there you should uncheck both if they are checked.. just to try that the issue does not come from there.
Hope it will be better for snapvue side. I let you answer that, and I will see later for the following issues.
I've tested -gm already before and it shows good vaules. But when I'm trying to go to SnapVue Side - there is nothing. Only black screen.
One more thing:
I have HardSPL already,
I've flashed liberated ROM, Flashed gullums ROM, and no go.
kristoff_sz said:
I've tested -gm already before and it shows good vaules. But when I'm trying to go to SnapVue Side - there is nothing. Only black screen.
One more thing:
I have HardSPL already,
I've flashed liberated ROM, Flashed gullums ROM, and no go.
Click to expand...
Click to collapse
well "good" values does not mean anything to me... I guess you mean "0" all the time (because you don't need to go in the bootloader).
and what do you see if you type use the -reset command (with snapvue in mode0) in snapvue? Do you see the HTC screen? (white) or nothing at all.. always black?
koala996 said:
well "good" values does not mean anything to me... I guess you mean "0" all the time (because you don't need to go in the bootloader).
and what do you see if you type use the -reset command (with snapvue in mode0) in snapvue? Do you see the HTC screen? (white) or nothing at all.. always black?
Click to expand...
Click to collapse
Good values means:
When i type -bl, then -gm it shows mode 1,
-mode0 then -gm - shows mode 0...
After reset its always black.
Now I cant run it even on this warning screen
Only 3G icon is blinking. Rest is black like ***hole
kristoff_sz said:
Good values means:
When i type -bl, then -gm it shows mode 1,
-mode0 then -gm - shows mode 0...
After reset its always black.
Now I cant run it even on this warning screen
Only 3G icon is blinking. Rest is black like ***hole
Click to expand...
Click to collapse
mmh.. I'm no help for that.. sorry
okay you see the 3G icon flickering,
What kind of shift you have x9500 ? x9000 ? x9510 ? as you described when battery is low the full screen is visible, you tried things like realVGA ? what version of hardspl you installed ??
Greets
Neutron83 said:
okay you see the 3G icon flickering,
What kind of shift you have x9500 ? x9000 ? x9510 ? as you described when battery is low the full screen is visible, you tried things like realVGA ? what version of hardspl you installed ??
Greets
Click to expand...
Click to collapse
Hello,
All i can find is "Clio110"
I didnt try anything like this. I can flash new ROM sometimes, but it just give nothing.
The HardSPL is latest one... (first one I've flashed anyway )
kristoff_sz said:
Hello,
All i can find is "Clio110"
I didnt try anything like this. I can flash new ROM sometimes, but it just give nothing.
The HardSPL is latest one... (first one I've flashed anyway )
Click to expand...
Click to collapse
clio110 stands for X9500.
you should try a tool in vista which display the WM part... I don't remember the name but I know that there exists at least one. I wish I remember that... grr.. was using it before my touch left me. and this utility allows to have a mouse in WinMob which is pretty nice ^^ (but useless IMO).
I will try to ask cmonex about your issue, but it seems that something is wrong.. but why? "hum"... you should try to flash cmonex's (rom and see what happens... his roms are the most secured and less modified and if it does not work with his rom, then it is coming from something else which might be harder to solve.
koala996 said:
clio110 stands for X9500.
you should try a tool in vista which display the WM part... I don't remember the name but I know that there exists at least one. I wish I remember that... grr.. was using it before my touch left me. and this utility allows to have a mouse in WinMob which is pretty nice ^^ (but useless IMO).
I will try to ask cmonex about your issue, but it seems that something is wrong.. but why? "hum"... you should try to flash cmonex's (rom and see what happens... his roms are the most secured and less modified and if it does not work with his rom, then it is coming from something else which might be harder to solve.
Click to expand...
Click to collapse
Can I ask you to provide link to ROM again? This one is cutted out .
Thank you for your help!
kristoff_sz said:
Can I ask you to provide link to ROM again? This one is cutted out .
Thank you for your help!
Click to expand...
Click to collapse
oups sorry here is the rom .. I have copied the link in shorter form instead of the real link sorry
koala996 said:
oups sorry here is the rom .. I have copied the link in shorter form instead of the real link sorry
Click to expand...
Click to collapse
Thanks.
Ok, new update: I've managed to flash that rom, but again - black screen always But there is one more thing:
I've run SnapVue (as I stated before - when there is "Battery low, device will turn off in...), and then started Windows - well, i had sound for a second, and I could change between XP and SV, but in a second - black screen again and under XP this message:
You just plugged device into audio jack.
And nothing. Sound is dead and SV side is dead... damn.
try flashing stock 1.30.405 then... I posted that somewhere (do a search for my posts in shift forum)
cmonex said:
try flashing stock 1.30.405 then... I posted that somewhere (do a search for my posts in shift forum)
Click to expand...
Click to collapse
Thank you for suggestion.
I've done as you stated... but nothing changes. At normal boot (after taking out battery), WInMo side wont work.
Any news in that thread anyone?
Did you check the WM power settings?
Did you check that the WM Advanced Power Settings was not switching the WM side off? Read my last post at http://forum.xda-developers.com/showthread.php?t=440437
You will need to use the Vista reset SnapVUE utility first to start it up first
*EDIT* Just re-read your first post and saw that you are running XP, oh well - if you can quickly start SnapVUE then check your power settings. Good Luck!
Hello every one,
This is my first post at this site but I am a regular visitor and getting help with my windows phones. I am having problem with my HTC mega. It start up normally, shows HTC logo and system information but when it go to windows screen it restarts and the cycle continues till I pull out battery. I have tried lots of stock roms including operetor speific (T-mobile, Orange etc) but no results. I cannot hardspl my phone as it does not go to windows and the jockey's hard spl required active sync or windows mobile data centre connection. Please help me out with the problem. Thanks and regards, Danish
You have to hard reset your phone, but you'll loose all your datas. To do it: turn on the phone and keep pressed volum up+down+end call.
psgarsenal said:
You have to hard reset your phone, but you'll loose all your datas. To do it: turn on the phone and keep pressed volum up+down+end call.
Click to expand...
Click to collapse
Thanks for the reply. I have had it hard reset many times but it doesn't work. Just a while back I had tried with inserting a custom OS and hardspl file in a stock ROM, which i did but phone refused to flash with the nbh file i created. For stock roms it flashes every time with whatever rom i try to flash withbut then again gets restarted at windows screen.
Then I cannot help you, sorry :/
psgarsenal said:
Then I cannot help you, sorry :/
Click to expand...
Click to collapse
Looking for expert opinion for my problem. Any one, please. regards,