Database Users

Phone Bricked Itself?

This is really weird. I am not sure what to do at this point. Here is the rundown on what happened:
I used the phone today, made phone calls, everything was fine. It was just sitting on my desk and then I got a call so I went to go answer it. When I tried to press answer, nothing happened. None of my other buttons would work either. I powered the phone off and rebooted it. It booted to the recovery image and is still stuck there.
I was running RC29 1.0 just followed the tutorial here http://forum.xda-developers.com/showthread.php?t=442480 to root it when I first got it and stopped installing the SPL. I had been thinking about upgrading to JF1.51 anyway so I thought this would be a good opportunity to force me to do it. I downloaded the new radio and the ROM. I installed both and the updates said they completed correctly. It still boots to the recovery image every time I turn it on.
For some more info, the phone will not reboot by pressing Home+Back like the recovery image says it should, I have to pull the battery to get it to turn off. Also, I can use adb to run commands on the phone.
Does anyone have any advice on where to go from here?? I've done a crap-ton of searching on here and across the internet and haven't been able to find much. If you need any more information on the situation please let me know. I would REALLY appreciate the help.

Your phone isn't bricked, so don't worry. Start over fresh from rooting, installing the DREAMIMG.nbh and the SPL. Follow the instruction carefully, and remember, Nandroid is your friend, so use it often.

Thanks for the look. I tried to do the process over again but holding down the camera button while powering on the phone will not bring me to the bootloader menu. It boots into the recovery utility every time.
Any other suggestions?

I still can't get anywhere with it? Does anyone have an idea on how I can get it into the bootloader?

Sorry for the huge post, but here is the dmesg output:
Code:
/ # dmesg
dmesg
[ 0.000000] Linux version 2.6.25-01843-gfea26b0 ([email protected]) (gc
c version 4.2.1) #5 PREEMPT Sun Nov 16 03:48:59 UTC 2008
[ 0.000000] CPU: ARMv6-compatible processor [4117b362] revision 2 (ARMv6TEJ),
cr=00c5387f
[ 0.000000] Machine: trout
[ 0.000000] AKM Data size = 1018 , 0x89768976, size = 4064
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 25856
[ 0.000000] DMA zone: 202 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 25654 pages, LIFO batch:7
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] trout_init_map_io()
[ 0.000000] clock_init()
[ 0.000000] ACPU running at 384000 KHz
[ 0.000000] WARNING - Bad VDD (0 != 3) for this freq
[ 0.000000] CPU0: D VIPT write-back cache
[ 0.000000] CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 s
ets
[ 0.000000] CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 s
ets
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 25654
[ 0.000000] Kernel command line: board_trout.disable_uart3=0 board_trout.usb_
h2w_sw=0 board_trout.disable_sdcard=0 board_trout.smisize=64 androidboot.baseba
nd=1.22.12.29 androidboot.bootloader=0.95.3000 androidboot.carrier=TMUS board_tr
out.keycaps=qwerty androidboot.mode=recovery androidboot.serialno=HT842GZ02076
[ 0.000000] Unknown boot option `board_trout.smisize=64': ignoring
[ 0.000000] Unknown boot option `androidboot.baseband=1.22.12.29': ignoring
[ 0.000000] Unknown boot option `androidboot.bootloader=0.95.3000': ignoring
[ 0.000000] Unknown boot option `androidboot.carrier=TMUS': ignoring
[ 0.000000] Unknown boot option `androidboot.mode=recovery': ignoring
[ 0.000000] trout_init_irq()
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.010000] Memory: 101MB = 101MB total
[ 0.010000] Memory: 97536KB available (2608K code, 760K data, 100K init)
[ 0.010000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] net_namespace: 440 bytes
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] trout_init() revision=128
[ 0.240000] trout_init: cpld_usb_hw2_sw = 0
[ 0.240000] trout_gpio_irq_handler: got masked interrupt: 0:84
[ 0.340000] msm_i2c_probe
[ 0.340000] msm_i2c_probe: clk_ctl 35d, 100000 Hz
[ 0.380000] Bluetooth: Core ver 2.11
[ 0.380000] NET: Registered protocol family 31
[ 0.380000] Bluetooth: HCI device and connection manager initialized
[ 0.380000] Bluetooth: HCI socket layer initialized
[ 0.380000] NET: Registered protocol family 2
[ 0.390091] Switched to high resolution mode on CPU 0
[ 0.470671] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.472838] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.473326] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.473601] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.473662] TCP reno registered
[ 0.501586] Unpacking initramfs... done
[ 1.052929] Freeing initrd memory: 1305K
[ 1.055554] Registered led device: lcd-backlight
[ 1.056195] smd_init()
[ 1.056286] smd_core_init()
[ 1.056530] smd_alloc_channel() 'SMD_RPCCALL' cid=2, shared=e010d9a0
[ 1.056927] smd_alloc_channel() 'SMD_DATA5' cid=11, shared=e0119a18
[ 1.057263] smd_alloc_channel() 'SMD_DATA6' cid=12, shared=e011da40
[ 1.057568] smd_alloc_channel() 'SMD_DATA7' cid=13, shared=e0121a68
[ 1.057873] smd_alloc_channel() 'SMD_DATA11' cid=17, shared=e01119c8
[ 1.058178] smd_alloc_channel() 'SMD_GPSNMEA' cid=27, shared=e0131b08
[ 1.058483] smd_alloc_channel() 'SMD_CS_A2M' cid=33, shared=e01159f0
[ 1.058758] smd_alloc_channel() 'SMD_DATA5_CNTL' cid=38, shared=e0125a90
[ 1.059063] smd_alloc_channel() 'SMD_DATA6_CNTL' cid=39, shared=e0129ab8
[ 1.059338] smd_alloc_channel() 'SMD_DATA7_CNTL' cid=40, shared=e012dae0
[ 1.059674] smd_core_init() done
[ 1.062441] SMD: ch 2 OPENING -> OPENED
[ 1.064241] hw3d: 0 init
[ 1.064760] msm_perf_init():
[ 1.066469] H2W: Registering H2W (headset) driver
[ 1.069033] input: h2w headset as /class/input/input0
[ 1.082502] RPC_TIME_TOD_SET_APPS_BASES:
[ 1.082532] tick = 343159
[ 1.082532] stamp = 3858764230
[ 1.084577] ashmem: initialized
[ 1.086134] yaffs Nov 16 2008 03:47:51 Installing.
[ 1.086317] io scheduler noop registered
[ 1.086408] io scheduler anticipatory registered (default)
[ 1.087324] logger: created 64K log 'log_main'
[ 1.087598] logger: created 256K log 'log_events'
[ 1.087873] logger: created 64K log 'log_radio'
[ 1.088087] ram_console: got buffer at 16d00000, size 20000
[ 1.088697] ram_console: uncorrectable error in header
[ 1.088880] ram_console: no valid data in buffer (sig = 0xffffffff)
[ 1.088941] console [ram-1] enabled
[ 1.091739] pmem: 1 init
[ 1.092807] pmem_adsp: 0 init
[ 1.094028] pmem_gpu0: 0 init
[ 1.095676] pmem_gpu1: 0 init
[ 1.100915] pmem_camera: 0 init
[ 1.102777] mddi_pmdh: init() base=0xe000b000 irq=16
[ 1.109307] get_smem_clock: state 10429 clock 0
[ 1.130000] smd_alloc_channel() 'SMD_DS' cid=0, shared=e0135b38
[ 1.130457] smd_alloc_channel() cid 7 does not exist
[ 1.131373] smd_alloc_channel() 'SMD_DATA2' cid=8, shared=e013db88
[ 1.132258] smd_alloc_channel() 'SMD_DATA3' cid=9, shared=e0141bb0
[ 1.133356] smd_alloc_channel() 'SMD_DATA4' cid=10, shared=e0145bd8
[ 1.140305] mddi cmd send rtd: int 3a000, stat 8063, rtd val d
[ 1.160793] mddi_pmdh: publish: mddi_c_d263_0000
[ 1.162960] vsync on gpio 97 now 0
[ 1.163601] mddi_pmdh: mddi_add_panel(c035f5e0, c02c2660)
[ 1.163967] mddi_pmdh: publish: mddi_panel
[ 1.164974] msmfb_probe() installing 320 x 480 panel
[ 1.200976] msm_serial: detected port #0
[ 1.201586] msm_serial.0: ttyMSM0 at MMIO 0xa9a00000 (irq = 9) is a MSM
[ 1.203051] msm_serial: driver initialized
[ 1.205340] loop: module loaded
[ 1.206011] PPP generic driver version 2.4.2
[ 1.206622] PPP Deflate Compression module registered
[ 1.207019] PPP BSD Compression module registered
[ 1.217568] allocated dma buffer at ffc01000, dma_addr 163db000
[ 1.218178] read CFG0 = aad400c0, CFG1 = 4745c
[ 1.218789] CFG0 = e8d408c0, CFG1 = 4745c
[ 1.219124] CFG0: cw/page=3 ud_sz=516 ecc_sz=10 spare_sz=1 num_addr_cycles=5
[ 1.219765] NAND_READ_ID = 1500aaec
[ 1.220152] status: c03120
[ 1.220518] nandid: 1500aaec maker ec device aa
[ 1.221129] CFG0: cw/page=3 ud_sz=512 ecc_sz=10 spare_sz=5
[ 1.221525] DEV_CMD1: f00f3000
[ 1.221861] NAND_EBI2_ECC_BUF_CFG: 1ff
[ 1.222441] flash_id: 1500aaec size 10000000
[ 1.222777] Creating 6 MTD partitions on "msm_nand":
[ 1.223387] 0x024c0000-0x02500000 : "misc"
[ 1.224608] 0x026c0000-0x02bc0000 : "recovery"
[ 1.225798] 0x02bc0000-0x02e40000 : "boot"
[ 1.227141] 0x02e40000-0x071c0000 : "system"
[ 1.228392] 0x071c0000-0x0b540000 : "cache"
[ 1.229643] 0x0b540000-0x10000000 : "userdata"
[ 1.231586] usb_probe() io=c6806000, irq=47, dma=ffc02000(163e5000)
[ 1.232929] usb_function_register() 'adb'
[ 1.233845] usb_function_register() 'usb_mass_storage'
[ 1.234211] msm_hsusb: functions bound. starting.
[ 1.234791] usb_bind_func() 'usb_mass_storage'
[ 1.235645] usb_mass_storage usb_mass_storage: Number of LUNs=1
[ 1.236042] usb_bind_func() 'adb'
[ 1.236622] adb_bind() c63d7874, c63d7a34
[ 1.237049] adb_bind() allocated 4 rx and 4 tx requests
[ 1.238453] usb_function_register() 'diag'
[ 1.239399] mice: PS/2 mouse device common for all mice
[ 1.240122] hsusb: IDLE -> ONLINE
[ 1.240793] hsusb: reset controller
[ 1.290122] ulpi: write 0x40 to 0x31
[ 1.290518] ulpi: write 0x1d to 0x0d
/ #
Looking at the Kernel Command Line message at the top makes it look like the phone doesn't know what any of the android.boot commands do so it defaults to recovery. Why would it be doing this?

the last post was too long to fix everything. here is the rest:
Code:
[ 1.291068] ulpi: write 0x1d to 0x10
[ 1.291403] ept #0 out max:64 head:ffc02000 bit:0
[ 1.291739] ept #1 out max:512 head:ffc02080 bit:1
[ 1.292288] ept #2 out max:512 head:ffc02100 bit:2
[ 1.292624] ept #0 in max:64 head:ffc02040 bit:16
[ 1.293204] ept #1 in max:512 head:ffc020c0 bit:17
[ 1.293540] ept #2 in max:512 head:ffc02140 bit:18
[ 1.293997] usb: notify offline
[ 1.294669] hsusb: ONLINE -> OFFLINE
[ 1.300610] msm_i2c msm_i2c.0: Error during data xfer (-5)
[ 1.311373] synaptics_ts_probe: Product Major Version 1
[ 1.313021] synaptics_ts_probe: Product Minor Version c
[ 1.314669] synaptics_ts_probe: product property 2
[ 1.316469] synaptics_ts_probe: device control 81
[ 1.318026] synaptics_ts_probe: interrupt enable 3
[ 1.320000] synaptics_ts_probe: 0xe0: 1 1 1 2 1 c 0 0
[ 1.320000] synaptics_ts_probe: max_x 3480, max_y 5368
[ 1.320000] synaptics_ts_probe: inactive_x -80 -80, inactive_y -32 -32
[ 1.320000] synaptics_ts_probe: snap_x 240-248 240-248, snap_y 80-88 80-88
[ 1.320000] input: synaptics-rmi-touchscreen as /class/input/input1
[ 1.370854] synaptics_ts_probe: Start touchscreen synaptics-rmi-touchscreen i
n interrupt mode
[ 1.371770] GPIO Event Driver
[ 1.372716] GPIO Keypad Driver: Start keypad matrix for trout-keypad-v3 in in
terrupt mode
[ 1.373692] No IRQF_TRIGGER set_type function for IRQ 191 (troutgpio)
[ 1.374364] No IRQF_TRIGGER set_type function for IRQ 192 (troutgpio)
[ 1.374852] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in inter
rupt mode
[ 1.375584] No IRQF_TRIGGER set_type function for IRQ 188 (troutgpio)
[ 1.376103] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in inter
rupt mode
[ 1.377476] input: trout-keypad-v3 as /class/input/input2
[ 1.430946] No IRQF_TRIGGER set_type function for IRQ 186 (troutgpio)
[ 1.431434] GPIO Input Driver: Start gpio inputs for trout-nav in interrupt m
ode
[ 1.432716] input: trout-nav as /class/input/input3
[ 1.491831] rs30000048:0da5b528 rs30000048:0da5b528: rtc core: registered msm
_rtc as rtc0
[ 1.496103] Registered led device: blue
[ 1.496897] Registered led device: green
[ 1.497782] Registered led device: red
[ 1.498361] AKM8976A compass driver: init
[ 1.498880] No IRQF_TRIGGER set_type function for IRQ 187 (troutgpio)
[ 1.500000] input: compass as /class/input/input4
[ 1.531129] pdev->dev.platform_data is not NULL
[ 1.531861] mt9t013: probe
[ 1.532197] mt9t013: init
[ 1.532502] mt9t013: mt9t013_register_init
[ 1.533082] mt9t013: camera sensor_reset set as 1
[ 1.535432] mt9t013: clk_get(vfe_mdc_clk): c02b2cd4
[ 1.535828] mt9t013: clk_get(mdc_clk): c02b2954
[ 1.536439] mt9t013: clk select 1
[ 1.536744] mt9t013: clk_get(vfe_clk): c02b2cb4
[ 1.537385] mt9t013: enable vfe_clk
[ 1.560091] mt9t013: clk select 0
[ 1.569277] mt9t013: camera sensor init sequence done
[ 1.569857] mt9t013: camera sensor suspend sequence
[ 1.570091] mt9t013: disabling vfe_clk
[ 1.570457] mt9t013: clk_put(vfe_clk): c02b2cb4
[ 1.571281] mt9t013: camera sensor suspend sequence done
[ 1.572258] Bluetooth: HCI UART driver ver 2.2
[ 1.572899] Bluetooth: HCI H4 protocol initialized
[ 1.573204] Bluetooth: HCILL protocol initialized
[ 1.574577] mmc0: Qualcomm MSM SDCC at 0x00000000e1000000 irq 24,0 dma -1
[ 1.575218] mmc0: 4 bit data mode enabled
[ 1.575554] mmc0: MMC clock 144000 -> 20000000 Hz, PCLK 64000000 Hz
[ 1.576134] mmc0: Slot eject status = 1
[ 1.576439] mmc0: Power save feature enable = 0
[ 1.577019] mmc0: PIO transfer enabled
[ 1.578392] mmc1: Qualcomm MSM SDCC at 0x00000000e1001000 irq 26,194 dma 8
[ 1.579002] mmc1: 4 bit data mode enabled
[ 1.579369] mmc1: MMC clock 144000 -> 20000000 Hz, PCLK 64000000 Hz
[ 1.580061] mmc1: Slot eject status = 0
[ 1.580396] mmc1: Power save feature enable = 0
[ 1.580732] mmc1: DM non-cached buffer at ffc04000, dma_addr 0x15805000
[ 1.581312] mmc1: DM cmd busaddr 360730624, cmdptr busaddr 360731392
[ 1.582472] Registered led device: spotlight
[ 1.583326] Registered led device: keyboard-backlight
[ 1.583967] Registered led device: button-backlight
[ 1.585188] No IRQF_TRIGGER set_type function for IRQ 190 (troutgpio)
[ 1.586683] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 1.595432] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.596103] TCP cubic registered
[ 1.596622] NET: Registered protocol family 1
[ 1.597415] NET: Registered protocol family 17
[ 1.597843] Bluetooth: L2CAP ver 2.9
[ 1.598422] Bluetooth: L2CAP socket layer initialized
[ 1.598789] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.599124] Bluetooth: SCO socket layer initialized
[ 1.600274] Bluetooth: RFCOMM socket layer initialized
[ 1.600732] Bluetooth: RFCOMM TTY layer initialized
[ 1.601312] Bluetooth: RFCOMM ver 1.9
[ 1.602105] clock_late_init() disabled 20 unused clocks
[ 1.604547] rs30000048:0da5b528 rs30000048:0da5b528: setting system clock to
2009-06-22 14:22:20 UTC (1245680540)
[ 1.605127] Freeing init memory: 100K
[ 1.833296] init: cannot open '/initlogo.rle'
[ 1.836988] init: Unable to open persistent property directory /data/property
errno: 2
[ 1.854486] enabling adb function
[ 1.857080] init: cannot find '/system/bin/akmd', disabling 'akmd'
[ 2.151251] init sharp panel
[ 2.205005] yaffs: dev is 32505860 name is "mtdblock4"
[ 2.205401] yaffs: passed flags ""
[ 2.205981] yaffs: Attempting MTD mount on 31.4, "mtdblock4"
[ 2.210763] yaffs: restored from checkpoint
[ 2.211404] yaffs_read_super: isCheckpointed 1
[ 2.568758] mmc_sd_init_card: Delay 250 ms
[ 2.682685] save exit: isCheckpointed 1
[ 2.910061] mmc1: host does not support reading read-only switch. assuming wr
ite-enable.
[ 2.910427] mmc1: new SD card at address b368
[ 2.912197] mmcblk0: mmc1:b368 SD01G 999936KiB
[ 2.912960] mmcblk0: p1
[ 3.040006] hsusb: OFFLINE -> ONLINE
[ 3.040006] hsusb: reset controller
[ 3.070128] ulpi: write 0x40 to 0x31
[ 3.070433] ulpi: write 0x1d to 0x0d
[ 3.070983] ulpi: write 0x1d to 0x10
[ 3.071288] ept #0 out max:64 head:ffc02000 bit:0
[ 3.071563] ept #1 out max:512 head:ffc02080 bit:1
[ 3.072112] ept #2 out max:512 head:ffc02100 bit:2
[ 3.072417] ept #0 in max:64 head:ffc02040 bit:16
[ 3.072936] ept #1 in max:512 head:ffc020c0 bit:17
[ 3.073241] ept #2 in max:512 head:ffc02140 bit:18
[ 3.073638] usb: notify offline
[ 3.078856] usb: suspend
[ 3.130006] usb: reset
[ 3.130006] usb: portchange
[ 3.130006] usb: reset
[ 3.130006] usb: portchange
[ 3.140006] usb_mass_storage usb_mass_storage: config #1
[ 7.352186] init: untracked pid 44 exited
[ 14.633174] init: untracked pid 57 exited
/ #

I didnt look through the dmesg out put but it sounds like your home key is stuck down.

Thats what I thought at first too but I still had full range of motion of the button when clicking it.
Anyway, I switched my SIM out to an older phone so I at least had something to use. Got back home and decided to try booting the phone without a SIM, booted to the setup screen. Powered off and put the SIM back in and it started up fine. Not positive that the SIM removal fixed it but its working! w00t!

can you describe the screen that it boots too? is it black with yellow text, grey backgound, rainbow, etc...
mm0

Now that it is working I would recommend to restart the whole process of Rooting and flashing your rom so that nothing is messed up.

Crap, its doing it again. I am pretty dang sure that the Home button is not stuck down, it clicks like normal, like it always has.
It boots up into the recovery screen, no matter if I try to boot into Bootloader mode (holding the camera button down) or not. It is the screen with the ! in the triangle and the picture of the phone. I have normal control while inside of it, can wipe and update, but I cannot restart by pressing Home+Back.
Is maybe the circuitry the handles the buttons bad? I really hope not, but does anyone have any other advice?

shameful bump.... I have tried everything I know how to do and I am really at a loss.

How good are you at taking things apart?
Is the phone under warranty or did you buy it used? If Its from tmobile then id call them up and explain what its doing. Run through everything they tell you to try and Im sure they will send out a replacement.
If its not under warranty then Id try taking it apart to see if the home button contacts are stuck.

I'm not too bad at it, just really paranoid of screwing something up. Ive taken apart my Tytn2 successfully before to change a digitzer. I bought the G1 used on eBay so I have no warranty whatsoever.
I'm almost convinced now it is the button, though. It started working again. My goal is to be just to not let the battery run dead .

KF Serial Port

I found the serial port on the Kindle Fire. Since I am new, I cannot post to the thread discussing it. They were right in it being that connector, but I scoped the pinout

Here is more information.. A capture of my FT232R sniffer board attached to the serial ports
The pinout of the connector:
1 - Rx In
2 -Tx Out
3 - Gnd
4 - Gnd
The connector has a '4' on it by one of the pins.
Texas Instruments X-Loader 1.41 (Sep 26 2011 - 18:22:43)
Starting OS Bootloader from EMMC ...
U-Boot 1.1.4-g70750ce2 (Jan 10 2012 - 06:20:06)
Load address: 0x80e80000
Board Rev.: 6
DRAM: 512 MB
Flash: 0 kB
<idme> write 3e to offset 0x1020
Using default environment
timed out in wait_for_pin: I2C_STAT=0
I2C read: I/O error
In: serial
Out: serial
Err: serial
PMIC TWL 6030 start conditions
PHOENIX_START_CONDITION :0x01
PHOENIX_LAST_TURNOFF_STS :0x01
PHOENIX_STS_HW_CONDITIONS:0x23
OMAP4 PRM_RSTST :0x00000001
Battery capacity =74 voltage=3923 temperature=27
Panel of LG
efi partition table:
256 128K xloader
512 256K bootloader
1024 10M dkernel
21504 192M dfs
414720 16M recovery
447488 64M backup
578560 10M boot
599040 5M splash
609280 512M system
1657856 1137M userdata
3986432 256M cache
4510720 5131M media
Read bootmode from the eMMC
bootmode = '0x0000000000004000'
Hit ESC key to stop autoboot: 0
kernel @ 80008000 (3118860)
ramdisk @ 81000000 (187080)
I2C read: I/O error
Blaze/SDP Board.
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35.7+ ([email protected]) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 SMP PREEMPT Tue Jan 10 06:22:28 UTC 2012
[ 0.000000] CPU: ARMv7 Processor [411fc093] revision 3 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: OMAP4430
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 118528
[ 0.000000] free_area_init_node: node 0, pgdat c0668da0, node_mem_map c076d000
[ 0.000000] Normal zone: 926 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 117602 pages, LIFO batch:31
[ 0.000000] ***********************
[ 0.000000] OMAP4430 ES2.3 type(GP)
[ 0.000000] id-code (6b95c02f)
[ 0.000000] Die-id (2C140026-00000001-0146876A-13006010)
[ 0.000000] Prod-id (0005B95C-000600F0)
[ 0.000000] Reset Reason(0x00000001)
[ 0.000000] ***********************
[ 0.000000] SRAM: Mapped pa 0x40300000 to va 0xfe400000 size: 0x100000
[ 0.000000] FIXME: omap44xx_sram_init not implemented
[ 0.000000] Reserving 5242880 bytes SDRAM for VRAM
[ 0.000000] SMC: Allocated workspace of 3M at (0x9c900000)
[ 0.000000] PERCPU: Embedded 9 pages/cpu @c1533000 s5696 r8192 d22976 u65536
[ 0.000000] pcpu-alloc: s5696 r8192 d22976 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117602
[ 0.000000] Kernel command line: console=ttyO2,115200n8 [email protected] init=/init vram=5M omapfb.vram=0:5M
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 463MB = 463MB total
[ 0.000000] Memory: 456760k/456760k available, 17352k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xdd000000 - 0xf8000000 ( 432 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdcf00000 ( 463 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0044000 ( 240 kB)
[ 0.000000] .text : 0xc0044000 - 0xc061a000 (5976 kB)
[ 0.000000] .data : 0xc061a000 - 0xc0669840 ( 319 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:388
[ 0.000000] omap_hwmod: sys_32k_ck: missing clockdomain for sys_32k_ck.
[ 0.000000] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
[ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
[ 0.000000] omap_hwmod: dmic: resetting
[ 0.000000] omap_hwmod: dss_dsi1: cannot be enabled (3)
[ 0.000000] omap_hwmod: dss_dsi2: cannot be enabled (3)
[ 0.000000] omap_hwmod: dss_hdmi: cannot be enabled (3)
[ 0.000000] omap_hwmod: dss_rfbi: cannot be enabled (3)
[ 0.000000] omap_hwmod: dss_venc: cannot be enabled (3)
[ 0.000000] omap_hwmod: iva: failed to reset in 10000 usec
[ 0.000000] omap_hwmod: mailbox: resetting
[ 0.000000] omap_hwmod: omap-mcpdm-dai: cannot be enabled (3)
[ 0.000000] omap_hwmod: mcspi1: resetting
[ 0.000000] omap_hwmod: mcspi2: resetting
[ 0.000000] omap_hwmod: mcspi3: resetting
[ 0.000000] omap_hwmod: mcspi4: resetting
[ 0.000000] omap_hwmod: mmc1: resetting
[ 0.000000] omap_hwmod: mmc2: resetting
[ 0.000000] omap_hwmod: mmc3: resetting
[ 0.000000] omap_hwmod: mmc4: resetting
[ 0.000000] omap_hwmod: mmc5: resetting
[ 0.000000] omap_hwmod: timer3: resetting
[ 0.000000] omap_hwmod: timer4: resetting
[ 0.000000] omap_hwmod: timer5: resetting
[ 0.000000] omap_hwmod: timer6: resetting
[ 0.000000] omap_hwmod: timer7: resetting
[ 0.000000] omap_hwmod: timer8: resetting
[ 0.000000] omap_hwmod: timer9: resetting
[ 0.000000] omap_hwmod: timer11: resetting
[ 0.000000] GPMC revision 6.0
[ 0.000000] SmartReflex CLASS3 initialized
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 2013.49 BogoMIPS (lpj=7864320)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] register_shrinker: no shrinker name registered for c0642e08
[ 0.000000] register_shrinker: registering shrinker from fs/inode.c
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys debug
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] Calibrating local timer...
[ 0.000000] 50.00MHz.
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c4, AUX_CTRL 0x1e470000
[ 0.000000] CPU1: Booted secondary processor
[ 0.000000] Brought up 2 CPUs
[ 0.000000] SMP: Total of 2 processors activated (4010.18 BogoMIPS).
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] EMIF0 is enabled with IRQ142
[ 0.000000] EMIF1 is enabled with IRQ143
[ 0.000000] OMAP GPIO hardware version 0.1
[ 0.000000] omap_mux_init: Add partition: #1: core, flags: 2
[ 0.000000] omap_mux_init: Add partition: #2: wkup, flags: 2
[ 0.000000] Reprogramming LPDDR2 timingsto 400000000 Hz
[ 0.000000] _omap_mux_init_signal: Could not set signal fref_clk0_out.gpio_wk6
[ 0.000000] ram_console: got buffer at 8e000000, size 40000
[ 0.000000] ram_console: no valid data in buffer (sig = 0x55555555)
[ 0.000000] console [ram-1] enabled
[ 0.000000] _omap_mux_init_gpio: Could not set gpio4
[ 0.000000] _omap_mux_init_signal: Could not set signal fref_clk4_req.gpio_wk7
[ 0.000000] _omap_mux_init_signal: Could not set signal c2c_data12.gpio_101
[ 0.000000] _omap_mux_init_signal: Could not set signal c2c_data12.gpio_101
[ 0.000000] res->start = 49022000
[ 0.000000] res->start = 49024000
[ 0.000000] res->start = 49026000
[ 0.000000] res->start = 48096000
[ 0.000000] OMAP DMA hardware revision 0.0
[ 0.000000] dma dma.0: System DMA registered
[ 0.000640] HSI: device registered as omap_hwmod: hsi
[ 0.013336] bio: create slab <bio-0> at 0
[ 0.015930] usbcore: registered new interface driver usbfs
[ 0.016143] usbcore: registered new interface driver hub
[ 0.016265] usbcore: registered new device driver usb
[ 0.016723] i2c_omap i2c_omap.1: bus 1 rev4.0 at 400 kHz
[ 0.017425] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[ 0.017974] twl6030: PIH (irq 39) chaining IRQs 368..387
[ 0.018218] TWL6030: Start condition(PHOENIX_START_CONDITION) is 0x01
[ 0.018371] TWL6030: Last turn off status (PHOENIX_LAST_TURN_OFF_STATUS) is 0x01
[ 0.018554] TWL6030: Hardware Conditions (PHOENIX_STS_HW_CONDITIONS) is 0x23
[ 0.027587] regulator: VMMC: 1200 <--> 3000 mV at 1800 mV normal standby
[ 0.028198] regulator: VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[ 0.028778] regulator: VUSIM: 1200 <--> 3000 mV at 3000 mV normal standby
[ 0.030029] regulator: VANA: 2100 mV normal standby
[ 0.031005] twl6030_enable: VCXIO state=0x55
[ 0.031005] regulator: VCXIO: 1800 mV normal standby
[ 0.031982] twl6030_enable: VDAC state=0x55
[ 0.031982] regulator: VDAC: 1800 mV normal standby
[ 0.032531] regulator: VUSB: 3300 mV normal standby
[ 0.033386] twl6030_enable: VAUX1_6030 state=0x55
[ 0.033569] regulator: VAUX1_6030: 1000 <--> 3200 mV at 2800 mV normal standby
[ 0.034423] twl6030_enable: VAUX2_6030 state=0x55
[ 0.034606] regulator: VAUX2_6030: 1200 <--> 3200 mV at 1800 mV normal standby
[ 0.035430] regulator: VAUX3_6030: 1000 <--> 3200 mV at 1200 mV normal standby
[ 0.035583] twl6030_usb_probe mbid=6
[ 0.035583] regulator_check_voltage: operation not allowed for VUSB
[ 0.036437] !!!!!BBSPOR_CFG = 72
[ 0.036560] !!!!!BBSPOR_CFG = 72
[ 0.037048] twl6030_usb twl6030_usb: Initialized TWL6030 USB module
[ 0.037170] i2c_omap i2c_omap.2: bus 2 rev4.0 at 400 kHz
[ 0.037506] i2c_omap i2c_omap.3: bus 3 rev4.0 at 400 kHz
[ 0.037689] i2c_omap i2c_omap.4: bus 4 rev4.0 at 400 kHz
[ 0.038696] bq27541 Driver
[ 0.038787] bq27541_probe
[ 0.051300] create_bq_procfs
[ 0.051452] Summit SMB347 Driver
[ 0.051513] summit_probe
[ 0.051544] Board id=6
[ 0.051727] Summit SMB347 detected, chip_id=0x6 board id=6
[ 0.051971] create_summit_procfs
[ 0.056671] omap4430_sdp_display_probe:Enter
[ 0.056793] Registered led device: led-orange
[ 0.057342] omap4430_sdp_display_probe:Exit
[ 0.057495] omap4430_keypad_led_probe:Enter
[ 0.057647] Registered led device: led-green
[ 0.058166] omap4430_keypad_led_probe:Exit
[ 0.058502] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.058990] Sangoma WANPIPE Router v1.1 (c) 1995-2000 Sangoma Technologies Inc.
[ 0.059234] Switching to clocksource timer-32k
[ 0.069885] musb_hdrc: version 6.0, musb-dma, peripheral, debug=0
[ 0.070068] musb_hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.070068] musb_hdrc: MHDRC RTL version 2.0
[ 0.070068] musb_hdrc: setup fifo_mode 4
[ 0.070098] musb_hdrc: 28/31 max ep, 16384/16384 memory
[ 0.070220] musb_hdrc musb_hdrc: USB Peripheral mode controller at fc0ab000 using DMA, IRQ 124
[ 0.070434] NET: Registered protocol family 2
[ 0.070526] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.070770] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.071044] TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
[ 0.071289] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.071319] TCP reno registered
[ 0.071319] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.071350] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.071502] NET: Registered protocol family 1
[ 0.084747] RPC: Registered udp transport module.
[ 0.084747] RPC: Registered tcp transport module.
[ 0.084777] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.084777] register_shrinker: no shrinker name registered for c06683d8
[ 0.084930] Trying to unpack rootfs image as initramfs...
[ 0.094055] Freeing initrd memory: 180K
[ 0.097229] ipu-power ipu0: Test of writing to the device message log,done from ipu_pm_init
[ 0.097259] ipu-power initialized ipu, major: 251, minor: 0
[ 0.097503] sdp4430_wifi_init: start
[ 0.097778] omap-iommu omap-iommu.0: ducati registered
[ 0.097839] omap-iommu omap-iommu.1: tesla registered
[ 0.098297] iovmm-omap initialized ducati, major: 250, base-minor: 0
[ 0.098510] iovmm-omap initialized tesla, major: 250, base-minor: 1
[ 0.099151] omap-remoteproc omap-remoteproc.0: omap_rproc_probe: adding rproc tesla
[ 0.099334] omap-remoteproc omap-remoteproc.0: omap-rproc initialized tesla, major: 249, base-minor: 0
[ 0.099365] omap-remoteproc omap-remoteproc.1: omap_rproc_probe: adding rproc ducati-proc0
[ 0.099517] omap-remoteproc omap-remoteproc.1: omap-rproc initialized ducati-proc0, major: 249, base-minor: 1
[ 0.099517] omap-remoteproc omap-remoteproc.2: omap_rproc_probe: adding rproc ducati-proc1
[ 0.099670] omap-remoteproc omap-remoteproc.2: omap-rproc initialized ducati-proc1, major: 249, base-minor: 2
[ 0.108551] register_shrinker: registering shrinker from mm/ashmem.c
[ 0.108551] ashmem: initialized
[ 0.116149] VFS: Disk quotas dquot_6.5.2
[ 0.116394] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.116424] register_shrinker: no shrinker name registered for c06432f0
[ 0.119262] register_shrinker: no shrinker name registered for c0643e8c
[ 0.119293] msgmni has been set to 892
[ 0.119323] SMC: Running on a GP device, SMC disabled
[ 0.120971] alg: No test for stdrng (krng)
[ 0.121002] io scheduler noop registered
[ 0.121032] io scheduler deadline registered
[ 0.121124] io scheduler cfq registered (default)
[ 0.176483] OMAP DSS rev 4.0
[ 0.176757] OMAP DISPC rev 4.0
[ 0.177062] OMAP DSI rev 3.0
[ 0.177368] OMAP DSI2 rev 3.0
[ 0.178161] Otter1 LCD probe called
[ 0.179229] omap_smartreflex_disable_reset_volt: omap_sr struct for sr_core not found
[ 0.179443] omap_smartreflex_enable: omap_sr struct for sr_core not found
[ 0.180023] omap-hsuart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[ 0.180267] omap-hsuart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[ 0.180450] omap-hsuart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[ 1.414672] console [ttyO2] enabled
[ 1.418670] omap-hsuart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[ 1.426361] bq27541 1-0055: termperature=270
[ 1.430938] summit_bat_notifier_call val=47
[ 1.442016] brd: module loaded
[ 1.454589] loop: module loaded
[ 1.458953] Bosch Sensortec Device detected!
[ 1.458953] BMA250 registered I2C driver!
[ 1.468658] input: bma250 as /devices/virtual/input/input0
[ 1.474975] android init
[ 1.477691] android_probe pdata: c063deb8
[ 1.482025] android_bind
[ 1.484680] android_bind_config
[ 1.488311] android_usb gadget: android_usb ready
[ 1.494903] f_adb init
[ 1.497406] android_register_function adb
[ 1.501617] f_mass_storage init
[ 1.504943] fsg_probe pdev: c063dc00, pdata: c063dea8
[ 1.510375] android_register_function usb_mass_storage
[ 1.515777] f_rndis init
[ 1.518615] android_register_function rndis
[ 1.523010] rndis_function_bind_config MAC: 02:03:41:37:34:30
[ 1.529083] android_usb gadget: using Quanta defined ethernet address
[ 1.535827] < Quanta_diagnostic > gpio_171 = 1 gpio_172 = 1 val = 3
[ 1.542663] < Quanta Diagnostic > set dev_addr done !
[ 1.545928] summit_smb347 4-0006: summit_fsm_stateTransform:state : suspend(0) -> suspend(0) ; event : EVENT_TEMP_PROTECT_STEP_6
[ 1.561004] android_usb gadget: using random host ethernet address
[ 1.577117] usb0: MAC 00:02:00:00:00:09
[ 1.581146] usb0: HOST MAC aa:a0:79:bf:ed:5e
[ 1.598480] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.605651] android_usb gadget: Number of LUNs=1
[ 1.610534] lun0: LUN: removable file: (no medium)
[ 1.615783] adb_bind_config
[ 1.619476] ilitek_init
[ 1.622924] twl6030_enable: VAUX3_6030 state=0x55
[ 1.660888] ilitek_i2c_probe, i2c new style format
[ 1.665893] ilitek_i2c_probe, IRQ: 0xC3
[ 1.670043] ilitek_i2c_register_device, add i2c device, success
[ 1.676239] ilitek_i2c_register_device, client.addr: 0x41
[ 1.681915] ilitek_i2c_register_device, client.adapter: 0xDC839848
[ 1.688415] ilitek_i2c_register_device, client.driver: 0xC065718C
[ 1.715759] ilitek_i2c_read_tp_info, firmware version 10.2.4.0
[ 1.739135] ilitek_i2c_read_tp_info, protocol version: 1.2
[ 1.762695] ilitek_i2c_read_tp_info, max_x: 3968, max_y: 2304, ch_x: 30, ch_y: 18
[ 1.770568] ilitek_i2c_read_tp_info, max_tp: 2, max_btn: 0
[ 1.776519] input: ilitek_i2c as /devices/platform/i2c_omap.2/i2c-2/2-0041/input/input1
[ 1.785095] ilitek_i2c_register_device, register input device, success
[ 1.792205] ilitek_i2c_register_device, request irq, success
[ 1.798156] ilitek_init, register chrdev(246, 0)
[ 1.804565] input: twl4030_pwrbutton as /devices/platform/i2c_omap.1/i2c-1/1-0049/twl4030_pwrbutton/input/input2
[ 1.816680] using rtc device, twl_rtc, for alarms
[ 1.821472] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 1.828491] twl_rtc twl_rtc: Power up reset detected.
[ 1.834899] twl_rtc twl_rtc: Enabling TWL-RTC.
[ 1.840026] i2c /dev entries driver
[ 1.844573] Linux video capture interface: v2.00
[ 1.853027] lm75 4-0048: hwmon0 driver: Found sensor 'tmp105'
[ 1.860717] OMAP Watchdog Timer Rev 0x00: initial timeout 240 sec
[ 1.868103] device-mapper: uevent: version 1.0.3
[ 1.873321] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: [email protected]
[ 1.882659] cpuidle: using governor ladder
[ 1.886932] cpuidle: using governor menu
[ 1.891662] mmci-omap-hs: probe of mmci-omap-hs.0 failed with error -16
[ 1.899261] omap_pwm_led omap_pwm_led: OMAP PWM LED (backlight) at GP timer 10/0
[ 1.907165] Registered led device: backlight
[ 1.913238] usbcore: registered new interface driver usbhid
[ 1.919097] usbhid: USB HID core driver
[ 1.923553] logger: created 64K log 'log_main'
[ 1.928375] logger: created 256K log 'log_events'
[ 1.933471] logger: created 128K log 'log_radio'
[ 1.938476] logger: created 64K log 'log_system'
[ 1.943481] logger: created 128K log 'log_metrics'
[ 1.953643] logger: created 64K log 'log_amazon_main'
[ 1.965759] register_shrinker: registering shrinker from drivers/staging/android/lowmemorykiller.c
[ 1.996032] OMAP4 reset reason is 0x00000001
[ 2.005706] TWL6030: Start condition(PHOENIX_START_CONDITION) is 0x01
[ 2.017608] TWL6030: Last turn off status (PHOENIX_LAST_TURN_OFF_STATUS) is 0x01
[ 2.035675] TWL6030: Hardware Conditions (PHOENIX_STS_HW_CONDITIONS) is 0x32
[ 2.048065] HSI DRIVER Version 0.4.1
[ 2.052062] omap_hsi omap_hsi.0: Registering IRQ hsi_p1_mpu (99)
[ 2.058380] omap_hsi omap_hsi.0: Registering IRQ hsi_dma_mpu (103)
[ 2.065002] omap_hsi omap_hsi.0: Trying to disable HSI IO wakeup on non HSI board
[ 2.072875] omap_hsi omap_hsi.0: HSI Hardware REVISION 0x50043101
[ 2.081176] omap_hsi omap_hsi.0: Trying to enable HSI IO wakeup on non HSI board
[ 2.093688] proc4430_drv_initializeModule
[ 2.098693] omap-devicehandler omap-devicehandler.0: omap_devh_probe: adding devh Tesla
[ 2.107269] omap-devh initialized Tesla, major: 240, base-minor: 0
[ 2.114013] omap-devicehandler omap-devicehandler.1: omap_devh_probe: adding devh SysM3
[ 2.122558] omap-devh initialized SysM3, major: 240, base-minor: 1
[ 2.129119] mmc0: new high speed DDR MMC card at address 0001
[ 2.129272] omap-devicehandler omap-devicehandler.2: omap_devh_probe: adding devh AppM3
[ 2.143585] omap-devh initialized AppM3, major: 240, base-minor: 2
[ 2.150482] snd_soc_init invoked..
[ 2.150543] mmcblk0: mmc0:0001 M8G2FA 7.20 GiB
[ 2.159057] mmcblk0:
[ 2.161804] +snd_soc_register_codec tlv320aic3110-codec
[ 2.167510] snd_soc_register_codec DRV c065e204
[ 2.172271] snd_soc_register_codec. Configured DRv c065e204
[ 2.178100] calling snd_soc_register_dais..
[ 2.182495] snd_soc_register_dais tlv320aic3110-codec 1
[ 2.187957] Registered DAI tlv320aic3110-MM_EXT
[ 2.192718] Invoking snd_soc_instantiate_cards...
[ 2.197631] -snd_soc_register_codec tlv320aic3110-codec
[ 2.203399] snd_soc_register_dais omap-abe-dai 7
[ 2.208282] Registered DAI MultiMedia1
[ 2.212219] Registered DAI MultiMedia2
[ 2.216156] Registered DAI Voice
[ 2.219543] Registered DAI Tones
[ 2.222900] Registered DAI Vibra
[ 2.226287] Registered DAI MODEM
[ 2.229675] Registered DAI MultiMedia1 LP
[ 2.234893] Entered omap4_evt_soc_init>...
[ 2.239227] OMAP4 EVT SoC init
[ 2.242401] Found Board EVT 2.1 then we use ABE support
[ 2.248291] +snd_soc_register_card ...
[ 2.252258] Card NumLinks 3
[ 2.255279] DAI Create runtime tlv320aic3110 Media LP Dynamic 1
[ 2.261474] DAI_link NullCodec Registration..
[ 2.266052] +snd_soc_register_codec soc-audio
[ 2.270629] snd_soc_register_codec DRV c0759e64
[ 2.275360] snd_soc_register_codec. Configured DRv c0759e64
[ 2.281219] calling snd_soc_register_dais..
[ 2.285583] snd_soc_register_dais soc-audio 1
[ 2.290161] Registered DAI null-codec-dai
[ 2.294372] Invoking snd_soc_instantiate_cards...
[ 2.299285] -snd_soc_register_codec null-codec
[ 2.303955] DAI Create runtime tlv320aic3110 Media Dynamic 1
[ 2.309875] DAI_link NullCodec Registration..
[ 2.314453] +snd_soc_register_codec soc-audio
[ 2.319000] snd_soc_register_codec DRV c0759e64
[ 2.323760] snd_soc_register_codec. Configured DRv c0759e64
[ 2.329589] calling snd_soc_register_dais..
[ 2.333984] snd_soc_register_dais soc-audio 1
[ 2.338531] Registered DAI null-codec-dai
[ 2.342742] Invoking snd_soc_instantiate_cards...
[ 2.347656] -snd_soc_register_codec null-codec
[ 2.352325] DAI Create runtime (Backend) FM-EXT Dynamic 0
[ 2.357971] Invoking the snd_soc_instantiate_cards..
[ 2.363159] Entered snd_soc_instantiate_card
[ 2.367645] Invoking soc_bind_dai_link 3 from instantiate_card
[ 2.373748] soc_bind_dai_link tlv320aic3110 Media LP at idx 0
[ 2.379791] codec->name null-codec dai name null-codec
[ 2.385162] Found All 4 Client Drivers..
[ 2.389282] Codec dca466c0 Codec_Dai dc884420 Platform dcb94dc0 CPU_DAI dcb44660
[ 2.397033] -soc_bind_dai_link RTD 1
[ 2.400756] soc_bind_dai_link tlv320aic3110 Media at idx 1
[ 2.406524] codec->name null-codec dai name null-codec
[ 2.411895] Found All 4 Client Drivers..
[ 2.416015] Codec dca466c0 Codec_Dai dc884420 Platform dcb94d40 CPU_DAI dcb44f60
[ 2.423767] -soc_bind_dai_link RTD 2
[ 2.427520] soc_bind_dai_link (Backend) FM-EXT at idx 2
[ 2.432983] codec->name tlv320aic3110-codec dai name tlv320aic3110-codec
[ 2.440002] Found All 4 Client Drivers..
[ 2.444122] Codec dca46540 Codec_Dai dcb44c60 Platform dcb94dc0 CPU_DAI dc971a20
[ 2.451873] -soc_bind_dai_link RTD 3
[ 2.455596] Calling snd_card_create
[ 2.459381] checking Card->probe 0
[ 2.462951] Card NumLinks 3 Calling probe_dai_link
[ 2.467956] soc_probe_dai_link OMAP4_KC1-ABE 0
[ 2.472595] cpu_dai->probed flag 0
[ 2.476165] codec->driver->probe 0
[ 2.479797] platform driver probe 0
[ 2.483551] Alternate GPT is invalid, using primary GPT.
[ 2.489135] p1 (xloader) p2 (bootloader) p3 (dkernel) p4 (dfs) p5 (recovery) p6 (backup) p7 (boot) p8 (splash) p9 (system) p10 (userdata) p11 (cache) p12 (media)
[ 2.510345] asoc: null-codec-dai <-> MultiMedia1 LP mapping ok
[ 2.516479] soc_probe_dai_link OMAP4_KC1-ABE 1
[ 2.521148] cpu_dai->probed flag 0
[ 2.524688] platform driver probe 0
[ 2.529083] asoc: null-codec-dai <-> MultiMedia2 mapping ok
[ 2.534912] soc_probe_dai_link OMAP4_KC1-ABE 2
[ 2.539611] cpu_dai->probed flag 0
[ 2.543426] invoking codec driver probe...
[ 7.242553] powerbutton_irqowir:action=release:
[ 8.439819] powerbutton_irqowip:action=press:
[ 8.957366] powerbutton_irqowir:action=release:
[ 9.284545] coming out of codec->driver probe...
[ 9.289398] codec->driver->probe c038a194
[ 9.293670] platform driver probe 1
[ 9.297302] entered the omap4_aic31xx_init function....
[ 9.502075] asoc: tlv320aic3110-MM_EXT <-> omap-mcbsp-dai.2 mapping ok
[ 9.509796] input: OMAP4_KC1-ABE Headset Jack as /devices/platform/soc-audio/sound/card0/input3
[ 9.519805] -snd_soc_register_card OMAP4_KC1-ABE
[ 9.524658] OMAP4 EVT Soc Init success..
[ 9.528778] ALSA device list:
[ 9.531890] #0: OMAP4_KC1_AIC3110-ABE
[ 9.536346] Netfilter messages via NETLINK v0.30.
[ 9.541351] nf_conntrack version 0.5.0 (7139 buckets, 28556 max)
[ 9.548034] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 9.555816] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 9.564117] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 9.570709] ctnetlink v0.93: registering with nfnetlink.
[ 9.576599] xt_time: kernel timezone is -0000
[ 9.581359] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.587127] arp_tables: (C) 2002 David S. Miller
[ 9.592041] TCP cubic registered
[ 9.595397] Initializing XFRM netlink socket
[ 9.600921] NET: Registered protocol family 10
[ 9.606079] lo: Disabled Privacy Extensions
[ 9.610809] Mobile IPv6
[ 9.613372] IPv6 over IPv4 tunneling driver
[ 9.618286] sit0: Disabled Privacy Extensions
[ 9.623382] ip6tnl0: Disabled Privacy Extensions
[ 9.628265] NET: Registered protocol family 17
[ 9.632995] NET: Registered protocol family 15
[ 9.637695] ThumbEE CPU extension supported.
[ 9.643493] omap_hwmod: Initialize debugfs support
[ 9.649719] Power Management for TI OMAP4.
[ 9.654418] prcm_clear_statdep_regs: Keep static depndencies
[ 9.660583] CPUidle for CPU0 registered
[ 9.665283] CPUidle for CPU1 registered
[ 9.669830] sr_init: No PMIC hook to init smartreflex
[ 9.675476] smartreflex smartreflex.0: omap_smartreflex_probe: SmartReflex driver initialized
[ 9.684509] smartreflex smartreflex.1: omap_smartreflex_probe: SmartReflex driver initialized
[ 9.693511] smartreflex smartreflex.2: omap_smartreflex_probe: SmartReflex driver initialized
[ 9.707214] Disabling unused clock "auxclk4_src_ck"
[ 9.712432] Disabling unused clock "hdq1w_fck"
[ 9.717102] Disabling unused clock "gpmc_ick"
[ 9.721679] Disabling unused clock "gpio4_dbclk"

I personally don't know how to interpret this, but I am sure someone will find it useful... Thanks!

@james
what does this mean to us?

qryptiq said:
@james
what does this mean to us?
Click to expand...
Click to collapse
It means the devs can finally enable bluetooth now that they can see error messages at the kernal level.
Sent from my myTouch_4G_Slide using XDA App

jamez70 said:
I found the serial port on the Kindle Fire. Since I am new, I cannot post to the thread discussing it.
Click to expand...
Click to collapse
Just to make sure I've got this right, are you referring to this thread?

jamez70 said:
Here is more information.. A capture of my FT232R sniffer board attached to the serial ports
The pinout of the connector:
1 - Rx In
2 -Tx Out
3 - Gnd
4 - Gnd
The connector has a '4' on it by one of the pins.
[...]
Click to expand...
Click to collapse
That's great! So, just to be clear, are pins 3 and 4 both GND? No VCC? I can see from your plot that it's about 1V8.
Also, could you give some more specifics on the communication? I assume something like;
Baud: 115200
Bits: 8
Parity: None
Stop Bits: 1
Edit: Which connector are we talking about anyway? We only guessed it to be 4 solder pads. No connector. Are these the pins you're talking about?

Does anyone know if it's possible to flash a new bootloader via the serial port?
My KF is dead since something went wrong while flashing FFF1.2
- Homer

UrticantOwl said:
Just to make sure I've got this right, are you referring to this thread?
Click to expand...
Click to collapse
Yeah thats correct. Maybe we can get them linked together.

-Homer- said:
Does anyone know if it's possible to flash a new bootloader via the serial port?
My KF is dead since something went wrong while flashing FFF1.2
- Homer
Click to expand...
Click to collapse
Yeah it may be possible. See if when you turn it on a USB connection appears for 2 seconds. If so, you can send x-loader over USB to it and boot anything you want.

I marked up this image to show the serial port location.

In the other discussion thread that I cannot reply to, they mentioned the 1.8/3.3V difference.
This will drop the 3.3V RX from the FTDI and divide it roughly down to 1.8V.

Also, I read the datasheet for the FT232R, and the VCCIO pin of the part (Pin 4), can be changed so that the I/O voltages are 1.8V. This is done by feeding 1.8V into pin 4.

jmcoffey said:
It means the devs can finally enable bluetooth now that they can see error messages at the kernal level.
Sent from my myTouch_4G_Slide using XDA App
Click to expand...
Click to collapse
Assuming that the TI chipset in the Jorjin module even supports Bluetooth. The available pictures from teardowns (namely ifixit.com's) show a model number WG7310-30 stamped on the module cover and inside that module, a TI WL1270B chipset. Unfortunately, the Jorjin site does not have information about this particular module but does for two others in this WG7310 series-- the WG7310-0A and WG7310-2A. The 0A uses the TI WL1270 chipset which is 802.11 b/g/n only and the 2A uses the TI WL1271 which has 802.11 b/g/n + BT 2.1 + FM. There's readily available information on the web for both of those chipsets (the WL1271 in particular, see TI's processor wiki or Omappedia) but I haven't seen anything for the WL1270B (try googling it with -kindle and -amazon). One interesting thing I've noticed looking at dmesg output on my own KF are references to the WL1273 chipset (which is what the Nook Tablet has in it I think?) and then there's this: pastebin.com/a4m6jc7T which looks to be dmesg output from KF (running a 2.6.35 kernel at) that showing BT drivers loading if title is to be believed. Hopefully somebody can finally get to the bottom of this now!

_ante_ said:
Assuming that the TI chipset in the Jorjin module even supports Bluetooth. The available pictures from teardowns (namely ifixit.com's) show a model number WG7310-30 stamped on the module cover and inside that module, a TI WL1270B chipset. Unfortunately, the Jorjin site does not have information about this particular module but does for two others in this WG7310 series-- the WG7310-0A and WG7310-2A. The 0A uses the TI WL1270 chipset which is 802.11 b/g/n only and the 2A uses the TI WL1271 which has 802.11 b/g/n + BT 2.1 + FM. There's readily available information on the web for both of those chipsets (the WL1271 in particular, see TI's processor wiki or Omappedia) but I haven't seen anything for the WL1270B (try googling it with -kindle and -amazon). One interesting thing I've noticed looking at dmesg output on my own KF are references to the WL1273 chipset (which is what the Nook Tablet has in it I think?) and then there's this: pastebin.com/a4m6jc7T which looks to be dmesg output from KF (running a 2.6.35 kernel at) that showing BT drivers loading if title is to be believed. Hopefully somebody can finally get to the bottom of this now!
Click to expand...
Click to collapse
At my last job, I had to get a WL1271 going in Android, and oddly enough I am doing the same thing again at my new job too.
I did notice that the WL1270 does NOT have bluetooth as well, so its probably more than likely that the KF does not contain bluetooth.
I did try 'microcom' (a part of Busybox I built and installed on the KF) and tried all the serial ports (ttyO0 - ttyO3) and I didn't see anything out there, but of course one would have to enable the BT_EN line to the chip to wake that part up.
If it did have bluetooth, finding the BT_EN line would be a tremendous amount of fun though!

jamez70 said:
At my last job, I had to get a WL1271 going in Android, and oddly enough I am doing the same thing again at my new job too.
I did notice that the WL1270 does NOT have bluetooth as well, so its probably more than likely that the KF does not contain bluetooth.
I did try 'microcom' (a part of Busybox I built and installed on the KF) and tried all the serial ports (ttyO0 - ttyO3) and I didn't see anything out there, but of course one would have to enable the BT_EN line to the chip to wake that part up.
If it did have bluetooth, finding the BT_EN line would be a tremendous amount of fun though!
Click to expand...
Click to collapse
Where would one begin the search for said line? I did get a kernel with BT enabled to at least start and load modules but it complained saying it couldn't find a bt device in /sys. Assuming the chip is ignoring such requests, where could I begin looking to 'wake it up'?

This is on 3.0, but it mentions BT as is implemented on a few places in the kernel. Don't know if it will spawn some ideas. https://github.com/KFire-Android/kernel_omap/blob/4AI.4/include/linux/rfkill.h

death2all110 said:
Where would one begin the search for said line? I did get a kernel with BT enabled to at least start and load modules but it complained saying it couldn't find a bt device in /sys. Assuming the chip is ignoring such requests, where could I begin looking to 'wake it up'?
Click to expand...
Click to collapse
Wow.. it could be anywhere. A schematic would be the best bet.
I looked in arch/arm/mach-omap2/board-4430kc1.c but that did not show anything.

jamez70 said:
Wow.. it could be anywhere. A schematic would be the best bet.
I looked in arch/arm/mach-omap2/board-4430kc1.c but that did not show anything.
Click to expand...
Click to collapse
I actually found a few things... ttyO1 BLUETOOTH_UART_DEV_NAME. Says BLUETOOTH_UART is UART2 and CONSOLE_UART is UART3
also appears as if is_bt_active is set to NULL
arch/arm/mach-omap2/board-4430kc1.c
Code:
#define BLUETOOTH_UART UART2
#define BLUETOOTH_UART_DEV_NAME "/dev/ttyO1"
#define CONSOLE_UART UART3
...
Code:
/* wl128x BT, FM, GPS connectivity chip */
struct ti_st_plat_data wilink_pdata = {
.nshutdown_gpio = 55,
.dev_name = BLUETOOTH_UART_DEV_NAME,
.flow_cntrl = 1,
.baud_rate = 3000000,
.suspend = plat_kim_suspend,
.resume = plat_kim_resume,
};
static struct platform_device wl128x_device = {
.name = "kim",
.id = -1,
.dev.platform_data = &wilink_pdata,
};
static struct platform_device btwilink_device = {
.name = "btwilink",
.id = -1,
};
#ifdef CONFIG_TI_ST
static bool is_bt_active(void)
{
struct platform_device *pdev;
struct kim_data_s *kim_gdata;
pdev = &wl128x_device;
kim_gdata = dev_get_drvdata(&pdev->dev);
if (st_ll_getstate(kim_gdata->core_data) != ST_LL_ASLEEP &&
st_ll_getstate(kim_gdata->core_data) != ST_LL_INVALID)
return true;
else
return false;
}
#else
[B]#define is_bt_active NULL[/B]
#endif
#endif
also...
...
Code:
static struct omap_uart_port_info omap_serial_platform_data[] = {
{
.use_dma = 0,
.dma_rx_buf_size = DEFAULT_RXDMA_BUFSIZE,
.dma_rx_poll_rate = DEFAULT_RXDMA_POLLRATE,
.dma_rx_timeout = DEFAULT_RXDMA_TIMEOUT,
.idle_timeout = DEFAULT_IDLE_TIMEOUT,
.flags = 1,
.plat_hold_wakelock = NULL,
[B].plat_omap_bt_active = NULL,[/B]
.rts_padconf = 0,
.rts_override = 0,
.cts_padconf = 0,
.padconf = OMAP4_CTRL_MODULE_PAD_SDMMC1_CMD_OFFSET,
.padconf_wake_ev = 0,
.wk_mask = 0,
},
Click to expand...
Click to collapse
so could that be what we're looking for?

I need a few more posts under my belt before I can insert links, but if you go to chipworks.com and click the "Chipworks Store" button (top right), you can type in "WL1270B" and search their report store. I'm not paying $200 for a photo of the die, but you can see from the description that is says:
Texas Instruments
WL1270B
Publish Date: Nov-11
The WL1270 is IEEE 802.11 b/g/n compliant power saving technology from Texas Instruments.
The only other WL127x chip in their catalog is the WL1271A with a description that clearly states that it provides mobile WLAN, Bluetooth, and FM on a single chip. This isn't absolutely 100% definitive, but it strongly suggests that the WL1270B is 802.11 b/g/n only. As for the lines in the code snippet from the last post-- not surprising, the driver in the stock rom probably supports a range of WL127x and WL128x chips.
Who knows, maybe we'll can still get lucky and one of these teardowns will show a different chip used in some production runs.

[Q] Display freezing after initial Xorg render

First off I have to say I'm somewhat cheating here, I am having this issue on my HOX+ Inter, but I've seen the exact same issue reported for the Nexus 7, both seem to be related to the Tegra 3 chip. Only difference is that the HOX+ forums are fairly dead since the Nexus 5 launch.
I am trying to run an X11 server from a Debian chroot from inside Android. Most of it is working so far.
My Debian chroot is set up, I have recompiled my ROM's kernel with my ROM's settings + the settings required for Xorg (VT support, System V IPC).
I have installed the Nvidia Linux For Tegra drivers.
I have a working xorg.conf file.
I have symlinked /dev/graphics/fd0 and /dev/graphics/fd0 to /dev/fd0 and /dev/fd1.
Of course, I have freed the screen (and more RAM) by stopping zygote/surfaceflinger/bootanimation
I can launch the Xorg server without problems, if I execute # X(org) -retro, it will show the normal gray screen with cursor.
However, this is where the problems start.
After the first rendered image, the screen stops responding. I can launch graphical apps over ssh or adb, they open as normal, except they are not rendered. The screen stays unmoved. I have also tried toying with xdotool, xrandr and xsetroot, the screen stays the same. As soon as the last X program exits, the screen flashes black for half a second, and goes back to the same unmoved state.
When I run x11vnc (which streams the *current* X session) in said session and open a graphical app, it opens fine over VNC, but the phone screen stays exactly the same.
I have seen more people having this problem, specifically on Tegra 3 devices, but haven't found any solutions yet.
I have experienced this problem on several ROMs/kernel configs, though I've only tried on 4.3 ROMs.
Currently I'm running Carbon ROM.
I'm running out of ideas myself, does anyone have any ideas on the matter?
My xorg.conf:
Code:
Section "Module"
Disable "dri"
Disable "dri2"
Disable "glx"
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
EndSection
Section "Device"
Identifier "Tegra"
Driver "tegra"
EndSection
My Xorg.0.log:
Code:
[ 7332.114]
X.Org X Server 1.14.3
Release Date: 2013-09-12
[ 7332.121] X Protocol Version 11, Revision 0
[ 7332.125] Build Operating System: Linux 3.2.0-4-mx5 armv7l Debian
[ 7332.129] Current Operating System: Linux localhost 3.1.10-BLADE #0 SMP PREEMPT Wed Nov 13 19:44:15 CET 2013 armv7l
[ 7332.131] Kernel command line: tegraid=30.1.3.0.0 [email protected] vmalloc=668M video=tegrafb zygote_oneshot=off kmemleak=off androidboot.lb=1 androidboot.carrier=HTC-Dutch androidboot.wipeddata=0 led=4 androidboot.keycaps=qwerty console=none usbcore.old_scheme_first=1 [email protected] nvdumper_reserved=0xbf7ff000 [email protected] panel_id=0x944a03 tegraboot=sdmmc gpt gpt_sector=122097663 androidboot.mode=normal batt_V=1048575 batt_I=1048575 batt_T=1048575 debug_uartport=hsport modem_id=0 androidboot.baseband=3.1204.168.32 androidboot.emmc=1 androidboot.sf=1 androidboot.skunum=1 androidboot.cid=HTC__E11 androidboot.mid=PM3511000 androidboot.serialno=FA2CXW105532 androidboot.mb_serialno=41HD12CV01419 androidboot.bootloader=1.35.0000 last_off_event=pmu_poweroff start_on_event=none hw_rst_reason=0x0 sw_rst_reason=0x77665501 project_phase=A radioflag=0x0 ats=0 hlog.ofs=296 un.ofs=364 androidboot.engid=0x0
[ 7332.148] Build Date: 09 October 2013 12:19:48AM
[ 7332.149] xorg-server 2:1.14.3-4 (Julien Cristau <[email protected]>)
[ 7332.149] Current version of pixman: 0.30.2
[ 7332.150] Before reporting problems, check http: wiki.x.org
to make sure that you have the latest version.
[ 7332.151] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 7332.157] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov 14 03:02:27 2013
[ 7332.160] (==) Using config file: "/etc/X11/xorg.conf"
[ 7332.162] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 7332.163] (==) No Layout section. Using the first Screen section.
[ 7332.163] (==) No screen section available. Using defaults.
[ 7332.164] (**) |-->Screen "Default Screen Section" (0)
[ 7332.164] (**) | |-->Monitor "<default monitor>"
[ 7332.165] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 7332.165] (**) | |-->Device "Tegra"
[ 7332.165] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 7332.165] (==) Automatically adding devices
[ 7332.165] (==) Automatically enabling devices
[ 7332.165] (==) Automatically adding GPU devices
[ 7332.165] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 7332.165] Entry deleted from font path.
[ 7332.165] (==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
built-ins
[ 7332.165] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 7332.168] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 7332.168] (II) Loader magic: 0x401eeec0
[ 7332.168] (II) Module ABI versions:
[ 7332.168] X.Org ANSI C Emulation: 0.4
[ 7332.168] X.Org Video Driver: 14.1
[ 7332.168] X.Org XInput driver : 19.1
[ 7332.168] X.Org Server Extension : 7.0
[ 7332.173] Initializing built-in extension Generic Event Extension
[ 7332.175] Initializing built-in extension SHAPE
[ 7332.175] Initializing built-in extension MIT-SHM
[ 7332.175] Initializing built-in extension XInputExtension
[ 7332.175] Initializing built-in extension XTEST
[ 7332.175] Initializing built-in extension BIG-REQUESTS
[ 7332.176] Initializing built-in extension SYNC
[ 7332.177] Initializing built-in extension XKEYBOARD
[ 7332.178] Initializing built-in extension XC-MISC
[ 7332.178] Initializing built-in extension SECURITY
[ 7332.178] Initializing built-in extension XINERAMA
[ 7332.178] Initializing built-in extension XFIXES
[ 7332.178] Initializing built-in extension RENDER
[ 7332.180] Initializing built-in extension RANDR
[ 7332.180] Initializing built-in extension COMPOSITE
[ 7332.180] Initializing built-in extension DAMAGE
[ 7332.180] Initializing built-in extension MIT-SCREEN-SAVER
[ 7332.180] Initializing built-in extension DOUBLE-BUFFER
[ 7332.180] Initializing built-in extension RECORD
[ 7332.180] Initializing built-in extension DPMS
[ 7332.181] Initializing built-in extension X-Resource
[ 7332.181] Initializing built-in extension XVideo
[ 7332.184] Initializing built-in extension XVideo-MotionCompensation
[ 7332.185] Initializing built-in extension SELinux
[ 7332.185] Initializing built-in extension XFree86-VidModeExtension
[ 7332.185] Initializing built-in extension XFree86-DGA
[ 7332.185] Initializing built-in extension XFree86-DRI
[ 7332.185] Initializing built-in extension DRI2
[ 7332.185] (WW) "dri" will not be loaded unless you've specified it to be loaded elsewhere.
[ 7332.185] (WW) "dri2" will not be loaded unless you've specified it to be loaded elsewhere.
[ 7332.186] (WW) "glx" will not be loaded unless you've specified it to be loaded elsewhere.
[ 7332.186] (II) "glx" will be loaded even though the default is to disable it.
[ 7332.186] (II) LoadModule: "extmod"
[ 7332.186] (II) Module "extmod" already built-in
[ 7332.186] (II) LoadModule: "tegra"
[ 7332.187] (II) Loading /usr/lib/xorg/modules/drivers/tegra_drv.so
[ 7332.197] (II) Module tegra: vendor="X.Org Foundation"
[ 7332.197] compiled for 1.13.99.901, module version = 0.4.0
[ 7332.197] Module class: X.Org Video Driver
[ 7332.197] ABI class: X.Org Video Driver, version 14.1
[ 7332.197] (II) NVIDIA driver for Tegra
[ 7332.198] (--) using VT number 2
[ 7332.198] (WW) Falling back to old probe method for tegra
[ 7332.199] (II) TEGRA(0): GPU is a T30
[ 7332.199] (II) TEGRA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 7332.199] (==) TEGRA(0): Depth 24, (--) framebuffer bpp 32
[ 7332.199] (==) TEGRA(0): RGB weight 888
[ 7332.199] (==) TEGRA(0): Default visual is TrueColor
[ 7332.200] (==) TEGRA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 7332.200] (**) TEGRA(0): Option "OverlayDepth" "255"
[ 7332.200] (**) TEGRA(0): Option "ARGBHWCursor" "true"
[ 7332.200] (II) TEGRA(0): Output LVDS-1 has no monitor section
[ 7332.200] (II) TEGRA(0): Output HDMI-1 has no monitor section
[ 7332.201] (WW) TEGRA(0): LVDS-1: Error querying display modes: No such device.
[ 7332.201] (II) TEGRA(0): EDID for output LVDS-1
[ 7332.201] (II) TEGRA(0): Printing probed modes for output LVDS-1
[ 7332.201] (II) TEGRA(0): Modeline "720x1280"x60.0 63.17 720 749 765 820 1280 1281 1282 1284 (77.0 kHz eP)
[ 7332.201] (II) TEGRA(0): EDID for output HDMI-1
[ 7332.201] (II) TEGRA(0): Output LVDS-1 connected
[ 7332.201] (II) TEGRA(0): Output HDMI-1 disconnected
[ 7332.201] (II) TEGRA(0): Using exact sizes for initial modes
[ 7332.201] (II) TEGRA(0): Output LVDS-1 using initial mode 720x1280
[ 7332.201] (II) TEGRA(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 7332.201] (--) TEGRA(0): VideoRAM: 32768 kByte
[ 7332.201] (--) TEGRA(0): Virtual size is 720x1280 (pitch 0)
[ 7332.202] (**) TEGRA(0): Driver mode "720x1280": 63.2 MHz, 77.0 kHz, 60.0 Hz
[ 7332.202] (II) TEGRA(0): Modeline "720x1280"x60.0 63.17 720 749 765 820 1280 1281 1282 1284 (77.0 kHz eP)
[ 7332.202] (==) TEGRA(0): DPI set to (96, 96)
[ 7332.202] (II) Loading sub module "fb"
[ 7332.202] (II) LoadModule: "fb"
[ 7332.202] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 7332.203] (II) Module fb: vendor="X.Org Foundation"
[ 7332.203] compiled for 1.14.3, module version = 1.0.0
[ 7332.203] ABI class: X.Org ANSI C Emulation, version 0.4
[ 7332.203] (II) Loading sub module "ramdac"
[ 7332.203] (II) LoadModule: "ramdac"
[ 7332.203] (II) Module "ramdac" already built-in
[ 7332.203] (--) Depth 24 pixmap format is 32 bpp
[ 7332.209] (==) TEGRA(0): Backing store disabled
[ 7332.209] (==) TEGRA(0): Silken mouse enabled
[ 7332.209] (II) TEGRA(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 7332.217] Loading extension TEGRA-EGL
[ 7332.217] (==) TEGRA(0): DPMS enabled
[ 7332.218] (--) RandR disabled
[ 7332.249] (II) SELinux: Disabled on system
[ 7332.254] (II) TEGRA(0): Setting screen physical size to 190 x 338
[ 7344.071] 6 XSELINUXs still allocated at reset
[ 7344.073] SCREEN: 0 objects of 184 bytes = 0 total bytes 0 private allocs
[ 7344.073] DEVICE: 0 objects of 64 bytes = 0 total bytes 0 private allocs
[ 7344.074] CLIENT: 0 objects of 100 bytes = 0 total bytes 0 private allocs
[ 7344.075] WINDOW: 0 objects of 28 bytes = 0 total bytes 0 private allocs
[ 7344.076] PIXMAP: 1 objects of 48 bytes = 48 total bytes 0 private allocs
[ 7344.077] GC: 4 objects of 16 bytes = 64 total bytes 0 private allocs
[ 7344.080] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.081] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.083] TOTAL: 6 objects, 116 bytes, 0 allocs
[ 7344.084] 1 PIXMAPs still allocated at reset
[ 7344.086] PIXMAP: 1 objects of 48 bytes = 48 total bytes 0 private allocs
[ 7344.087] GC: 4 objects of 16 bytes = 64 total bytes 0 private allocs
[ 7344.089] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.091] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.092] TOTAL: 6 objects, 116 bytes, 0 allocs
[ 7344.093] 4 GCs still allocated at reset
[ 7344.095] GC: 4 objects of 16 bytes = 64 total bytes 0 private allocs
[ 7344.096] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.097] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.098] TOTAL: 5 objects, 68 bytes, 0 allocs
[ 7344.099] 1 CURSORs still allocated at reset
[ 7344.101] CURSOR: 1 objects of 4 bytes = 4 total bytes 0 private allocs
[ 7344.103] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.104] TOTAL: 1 objects, 4 bytes, 0 allocs
[ 7344.104] 1 CURSOR_BITSs still allocated at reset
[ 7344.104] DBE_WINDOW: 0 objects of 12 bytes = 0 total bytes 0 private allocs
[ 7344.104] TOTAL: 0 objects, 0 bytes, 0 allocs
[ 7344.112] (II) TEGRA(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 7344.116] (==) TEGRA(0): DPMS enabled
[ 7344.116] (--) RandR disabled
[ 7344.134] (II) SELinux: Disabled on system
[ 7344.137] (II) TEGRA(0): Setting screen physical size to 190 x 338
[ 7346.348] (EE) Server terminated successfully (0). Closing log file.

Nougat on any Nexus device?

will we be able to install on Nexus 10?????

ScottBroker said:
will we be able to install on Nexus 10?????
Click to expand...
Click to collapse
If there's a developer that is willing to make a build for us. There's not many devs left for the Nexus 10 but hopefully someone will work on it.

Perhaps...

jsgraphicart said:
If there's a developer that is willing to make a build for us. There's not many devs left for the Nexus 10 but hopefully someone will work on it.
Click to expand...
Click to collapse
I really hope so. Perhaps CM will come through for us.

if it hasn't happened in a month or so, bug me - i'll do it

dmitrygr said:
if it hasn't happened in a month or so, bug me - i'll do it
Click to expand...
Click to collapse
dmitrygr, alreqdy got a build without errors, but not yet booting

scanno said:
dmitrygr, alreqdy got a build without errors, but not yet booting
Click to expand...
Click to collapse
How far did you get?
Got the build to succeed but it bootloops with the Google logo.
I have no idea how I can debug this... :'(

aHcVolle said:
How far did you get?
Got the build to succeed but it bootloops with the Google logo.
I have no idea how I can debug this... :'(
Click to expand...
Click to collapse
I have the same. The bootloop is caused by the failure of selinux to load:
Code:
[ 2.951989] init: init first stage started!
[ 2.959452] SELinux: avtab: invalid type or class
[ 2.963067] init: SELinux: Could not load policy: Invalid argument
[ 2.963314] init: failed to load policy: Invalid argument
[ 2.963400] init: Security failure; rebooting into recovery mode...
[ 2.963960] SysRq : Emergency Remount R/O
[ 2.964150] Emergency Remount complete
[ 4.762034] manta_otg manta_otg_work: UNDEFINED -> b_peripheral
[ 7.174875] manta_otg manta_otg_work: b_peripheral -> b_idle
[ 7.387529] manta_bat_sync_charge_enable: charger changed enable state to 1
[ 7.393069] battery: charge source type was changed: usb
[ 7.406743] manta_otg manta_otg_work: b_idle -> b_peripheral
[ 20.751453] INFO: task init:1 blocked for more than 10 seconds.
[ 20.751594] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 20.751670] init D c066e294 0 1 0 0x00000000

scanno said:
I have the same. The bootloop is caused by the failure of selinux to load:
Code:
[ 2.951989] init: init first stage started!
[ 2.959452] SELinux: avtab: invalid type or class
[ 2.963067] init: SELinux: Could not load policy: Invalid argument
[ 2.963314] init: failed to load policy: Invalid argument
[ 2.963400] init: Security failure; rebooting into recovery mode...
[ 2.963960] SysRq : Emergency Remount R/O
[ 2.964150] Emergency Remount complete
[ 4.762034] manta_otg manta_otg_work: UNDEFINED -> b_peripheral
[ 7.174875] manta_otg manta_otg_work: b_peripheral -> b_idle
[ 7.387529] manta_bat_sync_charge_enable: charger changed enable state to 1
[ 7.393069] battery: charge source type was changed: usb
[ 7.406743] manta_otg manta_otg_work: b_idle -> b_peripheral
[ 20.751453] INFO: task init:1 blocked for more than 10 seconds.
[ 20.751594] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 20.751670] init D c066e294 0 1 0 0x00000000
Click to expand...
Click to collapse
Who did you get this log?
Sorry for this noob question

aHcVolle said:
Who did you get this log?
Sorry for this noob question
Click to expand...
Click to collapse
Boot into TWRP, adb shell, cat /proc/last_kmsg
Seems like google upgraded policydb and the kernel has an old one that is not compatible with the selinux in android 7

Thanks!

Ugh this kernel needs a lot of work. @dmitrygr guess you do not have a list of commits you used for the M bringup. That squashed commit does not help to pinpoint the selinux problems. A clean merge with the 3.4 kernel from google / linux.org is not possible with the squashed commit, after reverting it, it was almost a clean merge.

Code:
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.67 ([email protected]) (gcc version 4.9 20150123 (prerelease) (GCC) ) #4 SMP PREEMPT Thu Sep 8 22:17:17 CEST 2016
[ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine: Manta
[ 0.000000] Initialized persistent memory from a0000000-a01fffff
[ 0.000000] ion_reserve: ion_chunk_heap reserved base 90000000 size 268435456
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU EXYNOS5250 (id 0x43520210)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] clkout: bad source 0
[ 0.000000] EXYNOS5: PLL settings, A=1000000000, B=1333090909, C=333000000
[ 0.000000] M=1600000000, E=96000000, V=300000000, G=533000000
[ 0.000000] EXYNOS5: ARMCLK=1000000000, CDREX=800000000, ACLK400=533000000
[ 0.000000] ACLK333=333000000, ACLK266=266666666, ACLK200=200000000
[ 0.000000] ACLK166=166500000, ACLK66=66666666
[ 0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_g3d: source is mout_mpll_user (0), rate is 800000000
[ 0.000000] sclk_gscl_wrap0: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_gscl_wrap1: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_bayer: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_jpeg: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_usbdrd30: source is mout_mpll (0), rate is 66666666
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1abe000 s12480 r0 d16192 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519938
[ 0.000000] Kernel command line: vmalloc=512M debug_core.break_on_panic=0 debug_core.break_on_exception=0 no_console_suspend s3c2410-wdt.tmr_atboot=1 s3c2410-wdt.tmr_margin=30 wire.search_count=5 androidboot.hardware=manta s3cfb.bootloaderfb=0x60000000 androidboot.bootloader=MANTALJ09 androidboot.serialno=R32CB0185CM androidboot.wifimacaddr=BC:20:A4:79:C4:6E androidboot.btmacaddr=BC:20:A4:79:C4:6D
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 4192256 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2047MB = 2047MB total
[ 0.000000] Memory: 1123232k/1123232k available, 972896k reserved, 648576K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] .text : 0xc0008000 - 0xc08ca000 (8968 kB)
[ 0.000000] .init : 0xc08ca000 - 0xc09140c0 ( 297 kB)
[ 0.000000] .data : 0xc0916000 - 0xc09672e0 ( 325 kB)
[ 0.000000] .bss : 0xc09df668 - 0xc0ab0d48 ( 838 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:597
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000048] Calibrating delay loop... 997.78 BogoMIPS (lpj=2494464)
[ 0.030034] pid_max: default: 32768 minimum: 301
[ 0.030149] Security Framework initialized
[ 0.030173] SELinux: Initializing.
[ 0.030351] Mount-cache hash table entries: 512
[ 0.031044] Initializing cgroup subsys debug
[ 0.031056] Initializing cgroup subsys cpuacct
[ 0.031065] Initializing cgroup subsys memory
[ 0.031095] Initializing cgroup subsys freezer
[ 0.031132] CPU: Testing write buffer coherency: ok
[ 0.031262] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.031293] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[ 0.031333] Setting up static identity map for 0x4071ba90 - 0x4071bae8
[ 0.093884] CPU1: Booted secondary processor
[ 0.121280] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.121319] CPU1: Unknown IPI message 0x1
[ 0.121446] Brought up 2 CPUs
[ 0.121458] SMP: Total of 2 processors activated (1995.57 BogoMIPS).
[ 0.133124] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 0.133321] gpiochip_add: registered GPIOs 0 to 7 on device: GPA0
[ 0.133333] gpiochip_add: registered GPIOs 9 to 14 on device: GPA1
[ 0.133344] gpiochip_add: registered GPIOs 16 to 23 on device: GPA2
[ 0.133355] gpiochip_add: registered GPIOs 25 to 29 on device: GPB0
[ 0.133364] gpiochip_add: registered GPIOs 31 to 35 on device: GPB1
[ 0.133374] gpiochip_add: registered GPIOs 37 to 40 on device: GPB2
[ 0.133383] gpiochip_add: registered GPIOs 42 to 45 on device: GPB3
[ 0.133393] gpiochip_add: registered GPIOs 47 to 53 on device: GPC0
[ 0.133403] gpiochip_add: registered GPIOs 55 to 58 on device: GPC1
[ 0.133412] gpiochip_add: registered GPIOs 60 to 66 on device: GPC2
[ 0.133421] gpiochip_add: registered GPIOs 68 to 74 on device: GPC3
[ 0.133431] gpiochip_add: registered GPIOs 76 to 79 on device: GPD0
[ 0.133440] gpiochip_add: registered GPIOs 81 to 88 on device: GPD1
[ 0.133450] gpiochip_add: registered GPIOs 90 to 95 on device: GPY0
[ 0.133459] gpiochip_add: registered GPIOs 97 to 100 on device: GPY1
[ 0.133468] gpiochip_add: registered GPIOs 102 to 107 on device: GPY2
[ 0.133478] gpiochip_add: registered GPIOs 109 to 116 on device: GPY3
[ 0.133487] gpiochip_add: registered GPIOs 118 to 125 on device: GPY4
[ 0.133497] gpiochip_add: registered GPIOs 127 to 134 on device: GPY5
[ 0.133506] gpiochip_add: registered GPIOs 136 to 143 on device: GPY6
[ 0.133515] gpiochip_add: registered GPIOs 145 to 151 on device: GPC4
[ 0.133525] gpiochip_add: registered GPIOs 153 to 160 on device: GPX0
[ 0.133534] gpiochip_add: registered GPIOs 162 to 169 on device: GPX1
[ 0.133543] gpiochip_add: registered GPIOs 171 to 178 on device: GPX2
[ 0.133553] gpiochip_add: registered GPIOs 180 to 187 on device: GPX3
[ 0.133567] gpiochip_add: registered GPIOs 189 to 196 on device: GPE0
[ 0.133577] gpiochip_add: registered GPIOs 198 to 199 on device: GPE1
[ 0.133586] gpiochip_add: registered GPIOs 201 to 204 on device: GPF0
[ 0.133595] gpiochip_add: registered GPIOs 206 to 209 on device: GPF1
[ 0.133604] gpiochip_add: registered GPIOs 211 to 218 on device: GPG0
[ 0.133613] gpiochip_add: registered GPIOs 220 to 227 on device: GPG1
[ 0.133623] gpiochip_add: registered GPIOs 229 to 230 on device: GPG2
[ 0.133632] gpiochip_add: registered GPIOs 232 to 235 on device: GPH0
[ 0.133641] gpiochip_add: registered GPIOs 237 to 244 on device: GPH1
[ 0.133655] gpiochip_add: registered GPIOs 246 to 253 on device: GPV0
[ 0.133665] gpiochip_add: registered GPIOs 255 to 262 on device: GPV1
[ 0.133674] gpiochip_add: registered GPIOs 264 to 271 on device: GPV2
[ 0.133683] gpiochip_add: registered GPIOs 273 to 280 on device: GPV3
[ 0.133692] gpiochip_add: registered GPIOs 282 to 283 on device: GPV4
[ 0.133704] gpio: GPZ has no PM function
[ 0.133713] gpiochip_add: registered GPIOs 285 to 291 on device: GPZ
[ 0.133928] dummy:
[ 0.134144] NET: Registered protocol family 16
[ 0.134479] Registered FIQ tty driver
[ 0.134514] Last reset was XnRESET pin reset (RST_STAT=0x10000)
[ 0.136730] Manta HW revision: 8, CPU EXYNOS5250 Rev1.0
[ 0.140206] console [ttyFIQ2] enabled
[ 0.140301] Registered fiq debugger ttyFIQ2
[ 0.140586] persistent_ram: found existing buffer, size 24788, start 24788
[ 0.203296] console [ram-1] enabled
[ 0.204992] bootloader fb located at 60000000-60F9FFFF
[ 0.205111] Registered chained gpio int handler for interrupt 77.
[ 0.205195] Registered interrupt support for gpio group 19.
[ 0.207404] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.207523] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.207708] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.208057] EXYNOS5250 PMU Initialize
[ 0.208950] EXYNOS: Initializing architecture
[ 0.209368] s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333, tin=divclk, base 0
[ 0.209550] s3c24xx-pwm s3c24xx-pwm.1: tin at 16666666, tdiv at 16666666, tin=divclk, base 8
[ 0.216848] bio: create slab <bio-0> at 0
[ 0.217244] MXT_BOOSTER:
[ 0.217421] MXT_XVDD:
[ 0.217535] MXT_XVDD: supplied by MXT_BOOSTER
[ 0.217772] VBATT: 3700 mV
[ 0.615102] ion_chunk_heap_create: base 2415919104 size 268435456 align 1048576
[ 0.615680] SCSI subsystem initialized
[ 0.616518] usbcore: registered new interface driver usbfs
[ 0.616675] usbcore: registered new interface driver hub
[ 0.616820] usbcore: registered new device driver usb
[ 0.617124] wake enabled for irq 439
[ 0.617235] wake enabled for irq 432
[ 0.617345] wake enabled for irq 433
[ 0.617454] GPIO Input Driver: Start gpio inputs for manta-keypad... in interrupt mode
[ 0.617575] wake enabled for irq 427
[ 0.617683] GPIO Input Driver: Start gpio inputs for manta-keypad... in interrupt mode
[ 0.617873] input: manta-keypad as /devices/virtual/input/input0
[ 0.618085] input: manta-switch as /devices/virtual/input/input1
[ 0.618614] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.618726] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.618789] s3c-i2c s3c2440-i2c.0: bus frequency set to 65 KHz
[ 0.619183] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.619249] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.619357] s3c-i2c s3c2440-i2c.1: bus frequency set to 378 KHz
[ 0.619716] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.619827] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.619890] s3c-i2c s3c2440-i2c.2: bus frequency set to 378 KHz
[ 0.620185] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[ 0.620251] s3c-i2c s3c2440-i2c.3: slave address 0x10
[ 0.620359] s3c-i2c s3c2440-i2c.3: bus frequency set to 378 KHz
[ 0.620664] s3c-i2c s3c2440-i2c.4: i2c-4: S3C I2C adapter
[ 0.620776] s3c-i2c s3c2440-i2c.4: slave address 0x10
[ 0.620839] s3c-i2c s3c2440-i2c.4: bus frequency set to 378 KHz
[ 0.621325] max77686 5-0009: device found
[ 0.628204] max77686_pmic_probe: Device ID=0x09, (version:1, chip_rev:1)
[ 0.628466] max77686-pmic max77686-pmic: Power on triggered by PWRON=High
[ 0.628532] max77686-pmic max77686-pmic: Power on triggered by Manual Reset Event
[ 0.631785] vdd_mif range: 850 <--> 1200 mV at 1037 mV
[ 0.632529] vdd_arm range: 850 <--> 1500 mV at 1075 mV
[ 0.633316] vdd_int range: 850 <--> 1300 mV at 1037 mV
[ 0.634059] vdd_g3d range: 850 <--> 1250 mV at 1200 mV
[ 0.635087] VCC_1.8V_AP: 1800 mV
[ 0.636067] VMIPI_1.0V: 1000 mV
[ 0.636841] TOUCH_VDD_1.8V: 1800 mV
[ 0.637871] VMIPI_1.8V: 1800 mV
[ 0.638839] VUOTG_3.0V: 3000 mV
[ 0.639810] VHSIC_1.0V: 1000 mV
[ 0.640787] VHSIC_1.8V: 1800 mV
[ 0.641577] 5M_CORE_1.5V: 1500 mV
[ 0.642294] CAM_IO_1.8V: 1800 mV
[ 0.643021] VT_CAM_1.8V: 1800 mV
[ 0.643790] TA_CHECK_1.35V: 1350 mV
[ 0.644516] TSP_AVDD_2.8V: 2800 mV
[ 0.645231] CAM_AF_2.8V: 2800 mV
[ 0.646202] VADC_3.3V: 3300 mV
[ 0.646850] 32KHZ_PMIC:
[ 0.647063] s3c-i2c s3c2440-i2c.5: i2c-5: S3C I2C adapter
[ 0.647128] s3c-i2c s3c2440-i2c.5: slave address 0x10
[ 0.647238] s3c-i2c s3c2440-i2c.5: bus frequency set to 378 KHz
[ 0.647508] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[ 0.647620] s3c-i2c s3c2440-i2c.7: slave address 0x10
[ 0.647682] s3c-i2c s3c2440-i2c.7: bus frequency set to 378 KHz
[ 0.647936] s3c-i2c s3c2440-i2c.8: i2c-8: S3C I2C adapter
[ 0.648001] s3c-i2c s3c2440-i2c.8: slave address 0x10
[ 0.648109] s3c-i2c s3c2440-i2c.8: bus frequency set to 378 KHz
[ 0.648228] Linux media interface: v0.10
[ 0.648372] Linux video capture interface: v2.00
[ 0.649822] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.650310] Bluetooth: Core ver 2.16
[ 0.650408] NET: Registered protocol family 31
[ 0.650471] Bluetooth: HCI device and connection manager initialized
[ 0.650584] Bluetooth: HCI socket layer initialized
[ 0.650646] Bluetooth: L2CAP socket layer initialized
[ 0.650773] Bluetooth: SCO socket layer initialized
[ 0.651126] cfg80211: Calling CRDA to update world regulatory domain
[ 0.651502] wake enabled for irq 421
[ 0.651634] wake enabled for irq 422
[ 0.652025] Switching to clocksource mct-frc
[ 0.668456] NET: Registered protocol family 2
[ 0.668686] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.669141] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.670183] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.671278] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.671388] TCP: reno registered
[ 0.671453] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.671529] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.671810] NET: Registered protocol family 1
[ 0.672078] Trying to unpack rootfs image as initramfs...
[ 0.729783] Freeing initrd memory: 1244K
[ 0.731326] Exynos5 : ARM Clock down on idle mode is enabled
[ 0.731484] EXYNOS5250 ASV(ARM : 6 MIF : 2) using fused group
[ 0.731879] [BT] bcm_bt_lpm_init
[ 0.732110] wake enabled for irq 438
[ 0.732592] exynos_tmu exynos_tmu: Current auto refresh interval(3875 nsec), Normal auto refresh interval(3875 nsec), memory throttle auto refresh internal(1937 nsec)
[ 0.733745] exynos_tmu exynos_tmu: Tmu Initialization is sucessful...!
[ 0.733964] s3c-adc samsung-adc-v4: operating without regulator "vdd" .
[ 0.734095] s3c-adc samsung-adc-v4: attached adc driver
[ 0.734639] audit: initializing netlink socket (disabled)
[ 0.734730] type=2000 audit(0.725:1): initialized
[ 0.735542] highmem bounce pool size: 64 pages
[ 0.741211] fuse init (API version 7.18)
[ 0.741464] msgmni has been set to 929
[ 0.743146] io scheduler noop registered
[ 0.743214] io scheduler deadline registered
[ 0.743289] io scheduler row registered
[ 0.743417] io scheduler cfq registered (default)
[ 0.945979] dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
[ 0.946098] dma-pl330 dma-pl330.0: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.948258] dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
[ 0.948377] dma-pl330 dma-pl330.1: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.949085] dma-pl330 dma-pl330.2: Loaded driver for PL330 DMAC-267056
[ 0.949154] dma-pl330 dma-pl330.2: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 0.949379] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.950120] exynos4210-uart.0: ttySAC0 at MMIO 0x12c00000 (irq = 83) is a S3C6400/10
[ 0.950312] exynos4210-uart.1: ttySAC1 at MMIO 0x12c10000 (irq = 84) is a S3C6400/10
[ 0.950546] exynos4210-uart.3: ttySAC3 at MMIO 0x12c30000 (irq = 86) is a S3C6400/10
[ 0.950886] mali mali.0: Continuing without Mali clock control
[ 0.951998] mali mali.0: GPU identified as 0x6956 r0p0 status 1
[ 1.088187] mali mali.0: Probed as mali0
[ 1.088423] mali mali.0: start latency exceeded, new value 958 ns
[ 1.089362] mali mali.0: state restore latency exceeded, new value 822666 ns
[ 1.089434] mali mali.0: stop latency exceeded, new value 875 ns
[ 1.094319] brd: module loaded
[ 1.096675] loop: module loaded
[ 1.097558] WM1811 LDO1:
[ 1.098053] WM1811 LDO2:
[ 1.102571] wm8994 7-001a: WM1811 revision D CUST_ID 00
[ 1.106510] bcm2079x-spi spi2.0: bcmspinfc_probe, probing bcmspinfc driver
[ 1.106700] bcm2079x-spi spi2.0: requesting IRQ 430
[ 1.106821] bcm2079x-spi spi2.0: bcmspinfc_probe, probing bcmspinfc driver exited successfully
[ 1.107088] tun: Universal TUN/TAP device driver, 1.6
[ 1.107151] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.107370] PPP generic driver version 2.4.2
[ 1.107532] PPP BSD Compression module registered
[ 1.107644] PPP Deflate Compression module registered
[ 1.107975] PPP MPPE Compression module registered
[ 1.108089] NET: Registered protocol family 24
[ 1.108188] usbcore: registered new interface driver asix
[ 1.108282] usbcore: registered new interface driver cdc_ether
[ 1.108417] usbcore: registered new interface driver net1080
[ 1.108505] usbcore: registered new interface driver cdc_subset
[ 1.108638] usbcore: registered new interface driver zaurus
[ 1.108789] usbcore: registered new interface driver cdc_ncm
[ 1.108981] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.109363] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 1.109543] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.109714] s5p-ehci s5p-ehci: irq 103, io mem 0x12110000
[ 1.117202] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 1.117381] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.117447] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.117557] usb usb1: Product: S5P EHCI Host Controller
[ 1.117619] usb usb1: Manufacturer: Linux 3.4.67 ehci_hcd
[ 1.117727] usb usb1: SerialNumber: s5p-ehci
[ 1.118103] hub 1-0:1.0: USB hub found
[ 1.118226] hub 1-0:1.0: 3 ports detected
[ 1.118505] s5p-ehci s5p-ehci: remove, state 1
[ 1.118577] usb usb1: USB disconnect, device number 1
[ 1.119856] s5p-ehci s5p-ehci: USB bus 1 deregistered
[ 1.120123] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.120447] exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller
[ 1.120633] exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 1
[ 1.120777] exynos-ohci exynos-ohci: irq 103, io mem 0x12120000
[ 1.176284] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.176399] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.176510] usb usb1: Product: EXYNOS OHCI Host Controller
[ 1.176572] usb usb1: Manufacturer: Linux 3.4.67 ohci_hcd
[ 1.176680] usb usb1: SerialNumber: exynos-ohci
[ 1.177025] hub 1-0:1.0: USB hub found
[ 1.177100] hub 1-0:1.0: 3 ports detected
[ 1.177431] exynos-ohci exynos-ohci: remove, state 1
[ 1.177502] usb usb1: USB disconnect, device number 1
[ 1.178015] exynos-ohci exynos-ohci: USB bus 1 deregistered
[ 1.178292] usbcore: registered new interface driver usblp
[ 1.178402] Initializing USB Mass Storage driver...
[ 1.178493] usbcore: registered new interface driver usb-storage
[ 1.178602] USB Mass Storage support registered.
[ 1.178936] s3c-hsotg : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
[ 1.178943] s3c-hsotg : version 15 March 2009
[ 1.179261] file system registered
[ 1.180162] gadget: Mass Storage Function, version: 2009/09/11
[ 1.180277] gadget: Number of LUNs=1
[ 1.180341] lun0: LUN: removable file: (no medium)
[ 1.180674] gadget: android_usb ready
[ 1.180738] bound driver 'android_usb'
[ 1.180921] mousedev: PS/2 mouse device common for all mice
[ 1.181226] usbcore: registered new interface driver xpad
[ 1.181319] usbcore: registered new interface driver usb_acecad
[ 1.181455] usbcore: registered new interface driver aiptek
[ 1.181541] usbcore: registered new interface driver gtco
[ 1.181674] usbcore: registered new interface driver hanwang
[ 1.181760] usbcore: registered new interface driver kbtab
[ 1.181893] usbcore: registered new interface driver wacom
[ 1.182388] input: Atmel maXTouch Touchscreen as /devices/platform/s3c2440-i2c.3/i2c-3/3-004a/input/input2
[ 1.192364] mali mali.0: stop latency exceeded, new value 959 ns
[ 1.192496] mali mali.0: state save latency exceeded, new value 8375 ns
[ 1.192851] pd-g3d: Power-off latency exceeded, new value 286958 ns
[ 1.292779] max77686-rtc max77686-rtc: max77686_rtc_enable_wtsr_smpl: WTSR: enable, SMPL: enable
[ 1.392693] max77686-rtc max77686-rtc: rtc core: registered max77686-rtc as rtc0
[ 1.393279] i2c /dev entries driver
[ 1.393982] exynos-mdev.0: Media0[0xde147800] was registered successfully
[ 1.394177] exynos-mdev.1: Media1[0xde147c00] was registered successfully
[ 1.394369] exynos-mdev.2: Media2[0xde19c000] was registered successfully
[ 1.394947] [INFO]gsc_probe:1450: gsc-0 registered successfully
[ 1.395461] [INFO]gsc_probe:1450: gsc-1 registered successfully
[ 1.395921] [INFO]gsc_probe:1450: gsc-2 registered successfully
[ 1.396419] [INFO]gsc_probe:1450: gsc-3 registered successfully
[ 1.396533] Initialize JPEG driver
[ 1.396807] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video12
[ 1.396938] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video11
[ 1.397382] Samsung Graphics 2D driver, (c) 2011 Samsung Electronics
[ 1.397489] EXYNOS MFC V4L2 Driver, (c) 2010 Samsung Electronics
[ 1.397926] s5p-mfc s5p-mfc: decoder registered as /dev/video6
[ 1.398059] s5p-mfc s5p-mfc: encoder registered as /dev/video7
[ 1.398621] i2c i2c-0: attached exynos hdcp into i2c adapter successfully
[ 1.398764] i2c-core: driver [exynos_hdcp] using legacy suspend method
[ 1.398827] i2c-core: driver [exynos_hdcp] using legacy resume method
[ 1.398946] Samsung HDMI output driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 1.399158] s5p-hdmi exynos5-hdmi: hdmiphy i2c bus number = 8
[ 1.399348] s5p-hdmiphy 8-0038: hdmiphy_probe start
[ 1.399414] s5p-hdmiphy 8-0038: probe successful
[ 1.425083] s5p-hdmi exynos5-hdmi: probe sucessful
[ 1.425258] i2c i2c-0: probed exynos edid
[ 1.425365] Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 1.425519] s5p-mixer s5p-mixer: probe start
[ 1.425802] s5p-mixer s5p-mixer: resources acquired
[ 1.425890] s5p-mixer s5p-mixer: added output 'S5P HDMI connector' from module 's5p-hdmi'
[ 1.426106] s5p-mixer s5p-mixer: registered layer mxr0_graph0 as /dev/video16
[ 1.426245] s5p-mixer s5p-mixer: registered layer mxr0_graph1 as /dev/video17
[ 1.426436] s5p-mixer s5p-mixer: registered layer mxr1_graph2 as /dev/video18
[ 1.426616] s5p-mixer s5p-mixer: registered layer mxr1_graph3 as /dev/video19
[ 1.426682] s5p-mixer s5p-mixer: mixer0 create links
[ 1.426801] s5p-mixer s5p-mixer: mixer1 create links
[ 1.426871] s5p-mixer s5p-mixer: mixer links are created successfully
[ 1.426995] s5p-mixer s5p-mixer: probe successful
[ 1.428101] fimc_is_spi successfully probed
[ 1.428187] Driver for 1-wire Dallas network protocol.
[ 1.500042] wake enabled for irq 420
[ 1.500412] s3c2410_wdt: S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 1.500665] s3c2410-wdt s3c2410-wdt: starting watchdog timer
[ 1.500735] s3c2410-wdt s3c2410-wdt: watchdog active, reset enabled, irq disabled
[ 1.501243] device-mapper: uevent: version 1.0.3
[ 1.501481] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
[ 1.501897] Bluetooth: HCI UART driver ver 2.2
[ 1.502010] Bluetooth: HCI H4 protocol initialized
[ 1.502210] cpuidle: using governor ladder
[ 1.502414] cpuidle: using governor menu
[ 1.502548] sdhci: Secure Digital Host Controller Interface driver
[ 1.502611] sdhci: Copyright(c) Pierre Ossman
[ 1.502798] Synopsys Designware Multimedia Card Interface Driver
[ 1.502964] dw_mmc dw_mmc.0: Using internal DMA controller.
[ 1.503389] mmc0: no vmmc regulator found
[ 1.505370] dw_mmc dw_mmc.0: Version ID is 241a
[ 1.505449] dw_mmc dw_mmc.0: DW MMC controller at irq 107, 32 bit host data width, 128 deep fifo
[ 1.505664] dw_mmc dw_mmc.1: Using internal DMA controller.
[ 1.506044] mmc1: no vmmc regulator found
[ 1.507344] dw_mmc dw_mmc.1: Version ID is 241a
[ 1.507412] dw_mmc dw_mmc.1: DW MMC controller at irq 108, 32 bit host data width, 128 deep fifo
[ 1.507523] dw_mmc dw_mmc.1: Internal DMAC interrupt fix enabled.
[ 1.517567] usbcore: registered new interface driver usbhid
[ 1.517691] usbhid: USB HID core driver
[ 1.532218] mmc_host mmc0: device is being hw reset
[ 1.692231] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
52 Corrected bytes, 0 unrecoverable blocks
Last reset was software reset (RST_STAT=0x20000000)
I have no idea what is missing but the display doesn't show anything when booting with a self compiled permissive kernel....

Just to let you all know

scanno said:
Just to let you all know
Click to expand...
Click to collapse
Nice. Looking forward to seeing how far this goes. How's it running?

jsgraphicart said:
Nice. Looking forward to seeing how far this goes. How's it running?
Click to expand...
Click to collapse
Too early to tell. Just got it booting. Wifi is working. Camera and gps not yet. BT and NFC not tried yet.

scanno said:
Too early to tell. Just got it booting. Wifi is working. Camera and gps not yet. BT and NFC not tried yet.
Click to expand...
Click to collapse
Well it's exciting to actually see it being done. I was afraid we wouldn't get anything for our Nexus 10

scanno said:
Too early to tell. Just got it booting. Wifi is working.
Click to expand...
Click to collapse
Don't need anything else!

scanno said:
Too early to tell. Just got it booting. Wifi is working. Camera and gps not yet. BT and NFC not tried yet.
Click to expand...
Click to collapse
Which kernel did you use?

aHcVolle said:
Which kernel did you use?
Click to expand...
Click to collapse
I used my own kernel (well the omnirom kernel and selinux patches).
This weekend i will sort out the patches and commit them.
You can check https://gerrit.omnirom.org/#/q/stat...anta+branch:android-7.0+topic:manta-n-bringup
I have most of them there already, but not yet verified by a new build.
---------- Post added at 10:36 AM ---------- Previous post was at 10:35 AM ----------
peachpuff said:
Don't need anything else!
Click to expand...
Click to collapse
Will upload the boot.img and system.img tonight.
But ut is a first booting build,expect problems and at your own risk. Only flashable by fastboot.
---------- Post added at 11:36 AM ---------- Previous post was at 10:36 AM ----------
https://www.androidfilehost.com/?w=files&flid=109935
Completely at your own risk
Wipe in twrp
Reboot into bootloader
fastboot flash boot boot.img
fastboot flash system system.img
fastboot reboot
And cross your fingers
Flashing system.img will give a signature failure, but it boots fine for me

AICP Phone Stuck at Logo during boot

Updated AICP today and I'm stuck at boot with the AICP logo... Here is what dmesg gives me:
Code:
[ 700.306266] voice_call_state_get: voice_call_state Off
[ 700.450763] msm_csid_init: CSID_VERSION = 0x30050000
[ 700.451654] msm_csid_irq CSID0_IRQ_STATUS_ADDR = 0x800
[ 700.460161] ====================== msm_sensor_power_up
[ 700.462547] MSM-CPP cpp_init_hardware:850 CPP HW Version: 0x60000000
[ 700.462564] MSM-CPP cpp_init_hardware:868 stream_cnt:0
[ 700.480582] msm_cci_init:1421: hw_version = 0x10040000
[ 700.480868] msm_get_otp_data: Enter
[ 700.480879] msm_get_otp_rear_camera_module_id: INFO: module_id is 0x9
[ 700.480884] msm_get_otp_rear_camera_module_id: sony_imx298 succeed
[ 700.480889] msm_sensor_match_id:imx298 OTP module id:0x9 expected module_id:0x9
[ 700.480892] msm_get_otp_data: Enter
[ 700.480896] msm_get_otp_rear_camera_vcm_id: INFO: vcm_id[0] is 0x09
[ 700.480900] msm_get_otp_rear_camera_vcm_id: INFO: vcm_id[1] is 0x05
[ 700.480903] msm_get_otp_rear_camera_vcm_id: INFO: vcm_id[2] is 0x1c
[ 700.480906] msm_get_otp_rear_camera_vcm_id: INFO: vcm_id[3] is 0x06
[ 700.480910] msm_sensor_match_id:eek:TP vcm id:0x6 expected vcm_id:0x6
[ 700.574085] msm_flash_subdev_do_ioctl:1427 Enter
[ 700.574158] msm_flash_subdev_ioctl:729 Enter
[ 700.574165] msm_flash_config:684 Enter msm_flash_config type 0
[ 700.574170] msm_flash_init:461 Enter
[ 700.574176] msm_flash_init:519 Exit<3>[ 700.574184] msm_flash_config:718 Exit msm_flash_config type 0
[ 700.574188] msm_flash_subdev_do_ioctl:1485 Exit
[ 700.590652] msm_qti_pp_get_rms_value_control, back not active to query rms be_idx:3
[ 700.592574] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 700.592631] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 700.592682] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 700.592687] msm_audio_sound_focus_get: Could not get copp idx for port_id=16385
[ 700.592733] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 700.592737] msm_audio_source_tracking_get: Could not get copp idx for port_id=16385
[ 700.592787] msm_voice_sound_focus_get: Error getting Sound Focus Params, err=-22
[ 700.592837] msm_voice_source_tracking_get: Error getting Source Tracking Params, err=-22
[ 700.592884] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 700.592888] msm_audio_sound_focus_get: Could not get copp idx for port_id=4101
[ 700.592935] msm_audio_get_copp_idx_from_port_id: Invalid FE, exiting
[ 700.592939] msm_audio_source_tracking_get: Could not get copp idx for port_id=4101
[ 700.594567] msm_flash_subdev_do_ioctl:1427 Enter
[ 700.594582] msm_flash_subdev_ioctl:729 Enter
[ 700.594589] msm_flash_config:684 Enter msm_flash_config type 1
[ 700.594596] msm_flash_off:401 Enter
[ 700.594616] msm_flash_off:413 Exit
[ 700.594621] msm_flash_config:718 Exit msm_flash_config type 1
[ 700.594626] msm_flash_subdev_do_ioctl:1485 Exit
[ 700.596206] msm_pcm_volume_ctl_get substream runtime not found
[ 700.596624] msm_pcm_volume_ctl_get substream runtime not found
[ 700.597381] msm_pcm_volume_ctl_get substream runtime not found
[ 700.597536] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.598061] msm_pcm_volume_ctl_get substream runtime not found
[ 700.598219] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.598672] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.599107] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.599551] msm_pcm_volume_ctl_get substream or runtime not found
[ 700.600098] msm_pcm_volume_ctl_get substream runtime not found
[ 700.600295] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.600815] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.601322] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.601717] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.602068] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.602422] msm_compr_audio_effects_config_get: stream or effects inactive
[ 700.607901] voice_call_state_get: voice_call_state Off
[ 700.609106] tasha_codec tasha_codec: tasha_mad_input_put: mic bias source not found for input = DMIC1
[ 700.624999] msm_csid_init: CSID_VERSION = 0x30050000
[ 700.625985] msm_csid_irq CSID2_IRQ_STATUS_ADDR = 0x800
[ 700.629203] MSM-CPP cpp_init_hardware:850 CPP HW Version: 0x60000000
[ 700.629213] MSM-CPP cpp_init_hardware:868 stream_cnt:0
[ 700.633399] ====================== msm_sensor_power_up
[ 700.647059] msm_cci_init:1421: hw_version = 0x10040000
[ 700.647330] msm_get_otp_data: Enter
[ 700.647337] msm_get_otp_front_camera_module_id: INFO: module_id is 0x2
[ 700.647341] msm_get_otp_front_camera_module_id: ov8865_plus succeed
[ 700.647345] msm_sensor_match_id:ov8865_sunny OTP module id:0x2 expected module_id:0x2
[ 703.392200] PWM device already freed
[ 703.392412] PWM device already freed
[ 703.392607] PWM device already freed
Any help would be great. I have tried re-flashing the update, as well as clearing cache, etc.

Ended up resetting the device. Please ignore