Hi,
I am unable to run the stock ROM Utility for my phone. I have tried doing what it says in the Read-Me file and it hasn't helped. I have tried it with phone running normally and in boot loader mode too, but I am getting this error all the time.
RUU_BlackStone_HTC_WWE_1.14.405.3_Radio_52.49a.25. 26_1.09.25.14_Ship is my stock ROM which I downloaded from wiki pages.
I want to load Energy ROM on my device from Miri. I would do it straight up i.e. normal ROM loading procedure but I've read that it's recommended to install the Stock ROM (No, I would not like to do Task 29 since I am sticking with USPL) and then install Energy.
I tried a bit but couldn't find any solutions.
Cheers.
What's wrong with going the HardSPL route?
I would like to stick to the stock SPL thats why.
I did try to evade that error by the way by going into bootloader mode and upgrading to the latest drivers and not the ones that we use to install cooked ROM's; the setup ran fine but then came back with the Invalid Vendor ID.
When I installed Miri's ROM, this is the exact ROM & Radio version I had, so how come I have had this error? Any ideas
I would give straight installation from Miri's to Energy a go but then at the moment Miri's ROM is running kind of "ok" apart from battery drainage and with upgrading without flashing the stock rom, I fear I might start to get those errors and I would be back to square one of flashing a stock ROM; hence my idea of flashing the stock ROM.
I found the solution. Apparently I was selecting the incorrect ROM. I realised that when I got the Invalid Vendor ID error. I bought this phone second hand and I just reliased that it was on Orange. Flash to Stock ROM worked now preparing to flash kwbr's ROM
Cheers
Related
Hi Guys, Need some help.
Have just flashed my ROM to Duttys new one, Hard SPL'd it first, which worked, now showing SPL-1.42.HSPL
Then I flashed to Duttys Rom, all went ok and completed sucessfully. Hard Reses afterwards, but now it won't boot up. It gets to preparing windows for first time use then resets and just hangs, any ideas any one?
Can you get into BootLoader Mode?
Maybe try to flash a shipped ROM first and after that retry the custom ROM
You probably forgot to flash the updated radio?
Thanks for the replies, I can get into the bootloader, so will revert back to the shipped ROM hopefully.
I thought the Radio was included in the Dutty ROM so didn't need flashing seperatly?
Most cooked ROMs don't have a radio built in. You have to identify the correct radio then flash that separately. This is becoming even more important with the new builds that require the latest radio's to work properly.
I can't understand why people don't take the time to research flashing properly before jumping in.
WB
Ok, I have found out that although it said it includes the radio, it doesn't, so there lies my problem, thanks guys. Off to find the Radio now.
I had flashed the Energy ROM and all the steps went well and the ROM was installed on the HD2 (TMo).
I then downloaded the Max Sense ROM and then it installed 100% but in the end gave me an error message. I went back to the Energy ROM and now it loaded fine but now on boot, it is stuck on "Internal Error". I tried a soft reset and a hard reset but it is simply stuck there. I cannot go past the message box. Please help.
NickPP said:
I had flashed the Energy ROM and all the steps went well and the ROM was installed on the HD2 (TMo).
I then downloaded the Max Sense ROM and then it installed 100% but in the end gave me an error message. I went back to the Energy ROM and now it loaded fine but now on boot, it is stuck on "Internal Error". I tried a soft reset and a hard reset but it is simply stuck there. I cannot go past the message box. Please help.
Click to expand...
Click to collapse
Task29 and Flash it again, btw what radio version is on your phone , and which Energy ROM , You should always include the following info when asking about ROM problems, helps troubleshoot,
ROM date/build/flavor(know this Max Sense) and Radio Version...
also you really should have posted this in the Energy ROM thread .... the Main one not the one here, the one in the Leo section ...
Task 29>Flash Rom>Flash Radio>Hard Reset on First Boot
That is a good procedure to use when flashing a new ROM, of course flashing the Radio is optional, but doesn't hurt ...
Thanks a lot man. Did the Task29 and all is well. I will follow your posting suggestions in the future for sure. Thanks again.
Problem:
Won't boot into any ROM.
Phone Details at Start:
Telstra HD2, HSPL 2.08, Radio 2.15.50.14, magldr 1.12, Windows Phone 7
Description:
I was running Windows Phone 7 when it decided to crash and restart. However it got stuck in a restarting loop; restart then crash during loading which caused it to restart then crash, etc. Then magldr came up with 1EFATAL HIT 1.
I figured WP7 had somehow corrupted part of the install but nothing I can do seems to fix it.
I have tried:
-Reflashing it with WP7.
-Reflashing it with another WP7 build.
-Reflashing to magldr 1.13 then WP7 again.
But none of these worked so I tried to go for a NAND Android build. However I couldn't get the ClockWork Mod to work. It too failed to boot with the same problem as WP7. Now I just wanted to get the phone in a working state again so I have tried:
-Formatting the SD card
-Reflashing to a custom winmob6.5 build
-Reflashing to a custom winmob6.5 build I had previously used and worked fine
-Changing the Radio to 2.14.50.02 then reflash to a custom wm6.5
-Changing the Radio to 2.12.50.02_02 then reflashing to a custom wm6.5
When I try the custom wm6.5 rom I see the boot screen but it just sits there and goes no further. I have tried installing an old copy of the chunky rom (as it changed the boot screen ) but still just sits at the boot screen.
I have tried redownloading all of the files I'm flashing with in case there was a problem downloading it. Also I have tried using files I already had which were working, but nothing seems to have fixed it.
Some things I have noticed are:
-that all flashings have and still load without error
-that it doesn't have any problems loading into the HSPL
-when ever I tried an install with magldr usb flash (CWM or WP7) it would work but at the end of the flash it said it would restart but never did. I had to remove the battery
-loading into magldr I could select the restart or powerdown option but it would just hang and again I had to remove battery to turn it off
Does anyone have any suggestions as to what I can try to get it fixed? The only things have haven't tried are flashing with a stock rom or reflashing another HSPL. Both of those I though could cause trouble for the currently working HSPL, which if I lost would cause more problems. Currrently I am under the impression it is a hardware failure as no rom (mb6.5, WP7 or CWM) will boot and magldr installed fine but wasn't able to restart the phone.
Check your battery pins to see if they're in anyway bent. If they are, just push them back a little bit with your finger.
Have you tried Task29? I think the only other way would be to flash stock again and start over.
Sent from my HTC Vision using XDA App
Skellyyy said:
Check your battery pins to see if they're in anyway bent. If they are, just push them back a little bit with your finger.
Have you tried Task29? I think the only other way would be to flash stock again and start over.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Yes, I have tried Task29 and then tried installing both magldr then CWM and wm6.5. It however didn't make a different as I still got the same error. Sorry, I forgot to mention this in initial post.
I have also read about the battery pins being bent. I haven't tried it but from what I can see mine are all about the same height and seem pretty straight. When I put in the battery they also seem to be pushed back a bit so I am assuming they are all making contact. I was a bit worried about over extending them but I might give it go if no other option becomes available.
I've seen several times people with a phone that seems to flash, but nothing actually changes.
The only way you can visually test this in your current state is to change spl to something different, and look in bootloader see if it changed, but you said you don't wanna, so.
You can try flashing HSPL 4 and select HSPL 3.03 and see if gbiz is sucessful. If you have HSPL 3.03 in bootloader then you know it is flashing and you can go back to HSPL 2.08. Also you can try flashing your stock Telstra ROM via USB cable and computer as this method will not change your HSPL 2.08 but flashing it via SD card will revert you back to SPL. I think flashing the stock ROM will be your best bet for now.
Well I originally had the energy boot screen and when I flashed to a copy of the chunky rom it changed to its one. I would have thought it was at least partly flashing. Also I have removed with magldr with task29 then reflashed (with magldr) and was able to boot into magldr. So I think the flashing is happening successfully.
I you think reflashing the HSPL could work then I'll give that a try. As I haven't done that yet. If that doesn't work I'll take a look at flashing the Telstra ROM. I know flashing a stock rom is mentioned as a solution but I wasn't sure why I would make the phone work any better than a custom rom with concerns to booting.
Thank you for your suggestions.
Just to cover all bases here, your HD2 is not getting really warm or warmer than usual is it? If so this is a sign of thermal breakdown, but like I said this is just to cover all bases here.
From what I can tell it hasn't been getting any hotter than usual.
Re:"why to use stock instead of custom"
Its because a stock rom flashes everything, spl, splashscreen, radio and rom.
Also, some customs use a secondary splashscreen, which would replace magldr, so if things aren't right, starting over by flashing your correct rom is often advised just to draw a line under the current attempts and start over.
Don't forget that even if the stock flash fails, if you did it from bootloader then Hspl is likely gone, and magldr too, possibly.
Just an update. I flash a Telstra ROM which to my surprise it booted... after a couple of tries. Decided to reboot it to see if it starting up was just luck which it turns out it was. I couldn't get it to start again then it refused to even get into the bootloader. So I am sure enough now that it is a hardware failure and am taking it in for warranty.
Thanks again for the help.
I'm sorry i know it's against the rules to be starting a new thread but it's been a week i've been asking for help and no one noticed. This is just a try to come noticed.
I installed task 29 on my blackstone. I had olinex 1.56 installed and later did the task29 with radio 1.13, 1.14 and 1.17 After successfully doing it i went on step 2 that is installing a clean rom. I tried these roms
blackSTONEhengeHyPerSlim_4_1
RUU_TOUCH_HD_MARYONE_23148_WWE_191110
WWE_1.56.405.1_Radio_52.62.25.Shipped ROm
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.34_1.13.25.24_Ship(3)
They get installed but after i store the contacts and everything it gets stuck if kept for like half an hr. The screen doesn't respond but power button and the volume button works.
I took my phone to a repair center and they couldn't fix it. So please help me i've just got only one phone.
I don't mean to offend any moderators by this but i'm just asking for your help. Thank You
Try reinstalling stock ROM after Task 29.
Restore ONLY contacts, and then try using device for several days.
DO NOT install any other software!!!
If it works, then problem is in some data or software you're restoring.
If not, restore original SPL and original ROM and try again.
If it does not work... and service can not help you... then sorry...
Hello i did reinstall the stock rom after task 29 and i was using pimbackup for restoring but that freezed my phone so i installed the stock rom again and thought of not using it. Did that but nothing much helped.
I hope believe these are the correct shipped roms
WWE_1.56.405.1_Radio_52.62.25.Shipped ROm
RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship(3)
Everything on xda has worked like wonders for me. Be it android on any other rom but right after task29 nothing seems to be working on my phone.
One thing i've noticed after installing any rom after task29 is if i get to the bootloader it gets me to a 1 sec white screen saying no image found. I hope what's causing a problem.
Do you understand WHAT Task 29 is?
It formats the partition drive of your device where the ROM resides. Meaning, it wipes any data regarding ROM.
So of course it would say "No image found".
I don't know which ROM is stock for your device. Try to update ROM via HTC site.
If lucky, it will suggest / let you find adequate ROM.
For my device it's 1.56.407.2 (German)!
If unlucky, it will say "Not supported" or something like that - then go for Orange 1.59.61.2 ROM.
And you might try one 1.5x ROM flash WITHOUT Task 29...
Just try installing stock ROM by stock RUU with USB cable. It will format data for you so you do not need any task 29 before flashing. If it doesn't work, try NOT restoring your contacts.
Thanks will do it and keep yu updated with it..
simplistian said:
Just try installing stock ROM by stock RUU with USB cable. It will format data for you so you do not need any task 29 before flashing. If it doesn't work, try NOT restoring your contacts.
Click to expand...
Click to collapse
Thanks i tried installing the stock rom like you told me but then got stuck on the screen alignment screen. I later installed blackSTONEhengeHyPerSlim_4_1 and now it's responding to every touch. Thanks alot. I hope this stays like this and yes instead of restoring i forwarded all the contacts through bluetooth. Owe you a BiiiiiiiiiiiiG thanks..
Too soon to be happy as same again..I don't think there should be a problem with touch as it works fine for first 1hr but right after something gets stored by something i mean contacts it stops reponding after sometime. The volume and power button work all fine. I can't make out the problem. Any ideas or suggestions. Shall i make a video and post ??
FIRST you have to make it work with factory settings - stock SPL and stock ROM.
After that flash what you like...
I think you have to follow Bodisson's suggestion, do everything as stock and retest without restoring anything. If it still failed...... you should have it repaired
Good luck!!
I had a very bad flash when I first tried Cloudy 0.7.
Unstable and freezing clock in TouchFLO (but NOT system clock!), crashing programs, very slow satelite lock with radio 1.17 on, sudden autolocking/unlocking...
So I did Task29, put on stock ROM (latest German 6.1), after that latest Orange to get newer radio, and after that Cloudy's 0.7.
Now I'm happy so far...
And I'll stick with radio 1.14 for now since it uses a bit less battery than 1.17...
Bodisson said:
I had a very bad flash when I first tried Cloudy 0.7.
Unstable and freezing clock in TouchFLO (but NOT system clock!), crashing programs, very slow satelite lock with radio 1.17 on, sudden autolocking/unlocking...
So I did Task29, put on stock ROM (latest German 6.1), after that latest Orange to get newer radio, and after that Cloudy's 0.7.
Now I'm happy so far...
And I'll stick with radio 1.14 for now since it uses a bit less battery than 1.17...
Click to expand...
Click to collapse
Glad to see somebody researching things out and settling on a radio he prefers due to performance rather than those just going for latest
I totally agree with spartan on this one. It's better to stick with old one's for performance rather than having problems with the latest one's. My device is working better than before but it does get stuck. I'm using stock rom with 6.1 and want to switch to 6.5 so looking for some compatible 6.5 rom with radio 1.14 maybe
Bodisson can you tell me all what you're using bro so that i can tr it on with my device.
kulwant said:
I totally agree with spartan on this one. It's better to stick with old one's for performance rather than having problems with the latest one's. My device is working better than before but it does get stuck. I'm using stock rom with 6.1 and want to switch to 6.5 so looking for some compatible 6.5 rom with radio 1.14 maybe
Bodisson can you tell me all what you're using bro so that i can tr it on with my device.
Click to expand...
Click to collapse
All rom's should work with each radio to be honest. Glad your device is working better, though still a little baffled why you're still having difficulties
EDIT - You are on a wm6.1 rom. Is the rom based on 1.56+, if not you may need to revert to HSPL 1.14
I know it got me bedazzled as well as i've flashed couple of times before but never faced any such difficulties. I even tried android on my phone and everything worked like charm. RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.34_1.13.25.24_Ship is what i'm using at the moment. I did try to flash it again with a 6.5 version rom but still gets stuck. The phone does get stuck once in a while if it is kept unused for a while so don't exactly know how to go on about it.
P.S: I know how hard it is to control things as an admin as i myself run a group. Photography in my case. Cheers
kulwant said:
I know it got me bedazzled as well as i've flashed couple of times before but never faced any such difficulties. I even tried android on my phone and everything worked like charm. RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.34_1.13.25.24_Ship is what i'm using at the moment. I did try to flash it again with a 6.5 version rom but still gets stuck. The phone does get stuck once in a while if it is kept unused for a while so don't exactly know how to go on about it.
P.S: I know how hard it is to control things as an admin as i myself run a group. Photography in my case. Cheers
Click to expand...
Click to collapse
I'm baffled but still want to get to the bottom of your issue and would appreciate any help from other members who may have idea's on how to solve your issue. From what I've read everything you have done is correct, but I don't like being stumped!!
If we start from the start, we may get to the bottom of this........
Ok it all started when i tried installing task 29. I flashed my blackSTONEhengeHyPerSlim_4_1 rom thinking task 29 will work awesomely fast with some newer version as it'll get installed as the default rom.
My phone started freezing like anything right after i flashed it with task 29. Right now my device is running on 1.56.405.1(43972) WWE and 1.13.25.24 rom and freezes again once in a while.
Just waiting for some miracle to make it work fine again.
kulwant said:
Ok it all started when i tried installing task 29. I flashed my blackSTONEhengeHyPerSlim_4_1 rom thinking task 29 will work awesomely fast with some newer version as it'll get installed as the default rom.
My phone started freezing like anything right after i flashed it with task 29. Right now my device is running on 1.56.405.1(43972) WWE and 1.13.25.24 rom and freezes again once in a while.
Just waiting for some miracle to make it work fine again.
Click to expand...
Click to collapse
Well as you know a T29 formats device so you need to flash a rom or you'll be stuck at boot screen. Before you do a T29 it states you must have HSPL on your device first. Now from what I've read you did have HSPL on first and your T29 worked as you where stuck at boot screen afterwards.
I'm assuming you turned device off, booted into bootloader then flashed youir rom (blackSTONEhengeHyPerSlim_4_1) which is based on 1.56+ as was your HSPL.
This all seems correct so I'm not sure what went wrong.
Is above all correct?
Did you try a T29 again and flash different rom or did you just flash different rom over existing?
I did task 29 on blackSTONEhengeHyPerSlim_4_1 and tried installing RUU_TOUCH_HD_MARYONE_23148_WWE_191110 in this process i started task 29 first and flashed it with radio 1.14 by placing the radio and task29 in same folder. Once done it got stuck with windows mobility. After that i restarted on bootloader once again and flashed it with RUU_TOUCH_HD_MARYONE_23148_WWE_191110 . It does get installed but then freezes on configuring device for first time use and then freezes big time on the screen for alignment. I had 1.56 installed before flashing with task 29. If the whole thing bypasses the align screen the rom will keep freezing big time.
That's been the whole issue.
kulwant said:
I did task 29 on blackSTONEhengeHyPerSlim_4_1 and tried installing RUU_TOUCH_HD_MARYONE_23148_WWE_191110 in this process i started task 29 first and flashed it with radio 1.14 by placing the radio and task29 in same folder. Once done it got stuck with windows mobility. After that i restarted on bootloader once again and flashed it with RUU_TOUCH_HD_MARYONE_23148_WWE_191110 . It does get installed but then freezes on configuring device for first time use and then freezes big time on the screen for alignment. I had 1.56 installed before flashing with task 29. If the whole thing bypasses the align screen the rom will keep freezing big time.
That's been the whole issue.
Click to expand...
Click to collapse
Right, I never put any files in same folder as it only confuses flashing process and can cause issues. I.e. put T29 in its own folder, radio 1.14 in its own folder and then rom in another folder.
Do a T29 and when its complete, I.e. stuck in smart mobility screen. Then you take out battery to turn phone off. After this put phone into bootloader and flash rom. Then flash radio after it as a lot of roms have a radio file included
...........................
Sent from the improved version of Tapatalk, better known as Forum Runner
Hi guys,
I wanted to return to the original W.M 6.5 in order to install new Android NAND, so I formatted my SD card, placed the image and loaded the bootloader. Unfortunately, the installation was interrupted. After that when trying to repeat the procedure bootloader says "Upgrade ROM code error Please try again" . I am trying again, but the same thing happens over and over again. I tried installing it via USB connection, but it installs 1% and gives the same error "000028002 NOT ALLOW".
Does that mean that I have bricked my phone and if not, how am I to fix that and install what I wanted to install?
Message says it all. ROM code error.
Fliashing from SD will remove HSPL so you have no CID bypass.
ROM you are flashing is not matching your devices country ID so you need to find a ROM that is correct to flash via SD or flash via USB & flash a suitable HSPL first.
Before proceeding flashing, check ROM & radios are correct for your device as too many people are bricking their devices by silly mistakes these days.
Thank you!
My phone is an Orange bought form UK. I fount the required ROM (ver. 3.14), but the same thing happens again. I tried to find the original 1.72, but it cannot be foung anywhere. Any ideas?
Flash HSPL via USB then ROM via USB
I managed to install the stock ROM, now I am going to pick a nice NAND Adnroid.
Thanks for the help, much appreciated!