hello i have an hd2 tmobile branded i cannot seem to hspl it because on 1024 i get usb conectiong failed but it does go on tri color screen and in hspl2 i get bad model id.
this is what i have on my tricolor:
PB81120 SS-B3
SPL-20.8.0000 8G XE
MICROP LED 0X05
MICROP TOUCH 0X40
PLEASE HELP =/
THANKS IN ADVANCE.
this is what you need my friend..
then you will be able to download the tmobile energy rom
http://rapidshare.com/files/368532303/HSPL2_1024_RUN.zip
HI,
I used the HSPL2_1024, selected the 2.0.0.8
After 10 min, of using Energy.Leo.23549.Sense2.5_TMobile_USA.Mar.26
I got an error, I recovered, but wondering what happened??
Just try it again. Make sure your drivers are all complete from Windows Vista or 7. Make sure you are running 6.1 Windows Mobile Device Center.
I am sure you have done this but make sure:
Plug in your phone make sure the drivers are good with Active Sync on.
When you get into HSPL2_1024 and let it run your device will be found again in USB mode. Just to make sure the drivers are loaded correctly.
Flash - reboot and then flash the Energy or whatever USTMO compatible cooked ROM you like. I think there are only 2/3 that work with the ROM 2.08
Sometimes it just takes retracing your steps to get it to work right.
good luck.
I didn't want to make a new thread for this and clutter up the board, I'm kind of a noob to XDA you see. I just bought a Tmobile HD2 and downloaded and applied the HSPL linked in this thread, it all worked fine. My problem is: Will installing the 2.09.51.03 radio on my tmous HD2 hurt it? Was the 2.09 radio meant for the htc hd2 which has a different radio?
My main goal is to get Artemis rom on it.
Thanks for your time.
Lazarpandar said:
I didn't want to make a new thread for this and clutter up the board, I'm kind of a noob to XDA you see. I just bought a Tmobile HD2 and downloaded and applied the HSPL linked in this thread, it all worked fine. My problem is: Will installing the 2.09.51.03 radio on my tmous HD2 hurt it? Was the 2.09 radio meant for the htc hd2 which has a different radio?
My main goal is to get Artemis rom on it.
Thanks for your time.
Click to expand...
Click to collapse
The .51 radios are meant for the European spec and will not work on a TMOUS based rom AFAIK.
yeah i have installed mobile center twice straight from microsoft, my phone is synced with it, i run the 1024 it says connecting 5 min later says usb connection failed my phone does go into the tri color screen with the USB at the bottom =/ please really help
S3BAZ10 said:
yeah i have installed mobile center twice straight from microsoft, my phone is synced with it, i run the 1024 it says connecting 5 min later says usb connection failed my phone does go into the tri color screen with the USB at the bottom =/ please really help
Click to expand...
Click to collapse
try different usb ports and remember to right click 1024 and 'run as administrator'
After using the HardSPL I could not get my phone to sync either... So Just put your phone into bootloader mode. Turn off phone, power button, volume down hold till tri color screen comes up. Then just run the RUU an it will flash your phone. Only NRGZ rom works.
richsark said:
HI,
I used the HSPL2_1024, selected the 2.0.0.8
After 10 min, of using Energy.Leo.23549.Sense2.5_TMobile_USA.Mar.26
I got an error, I recovered, but wondering what happened??
Click to expand...
Click to collapse
You have to choose. 2.0.0.8 HSPL
msmith1991 said:
this is what you need my friend..
then you will be able to download the tmobile energy rom
http://rapidshare.com/files/368532303/HSPL2_1024_RUN.zip
Click to expand...
Click to collapse
Would anyone happen to have a mirror to this link, or could some kind soul possibly upload it? This one seems to be broken. It would be greatly appreciated.
Update...I found it.
yeah notinh still not working ive tryed all ports, im running windows 7 64bit.
I'm recieving the same error. Windows 7 x64, MDC is latest 6.1. Tried from both laptop (Win7 x64) and desktop (Win7 x64). Phone goes into Tri color screen, says "USB" at the bottom. Windows notes new driver, updates, then HSPL2 for 1024 Leo gives "Critical Error" and bombs out. Bummer
UPDATE: Fixed it. Did a hard reset on the phone, tried again, and now HSPL flashed successfully. Now, on to the cooked ROMs
Worked for me on win 7 x64... No issue with HSPL2_1024_RUN file I got by browsing this site... It did freeze on me during RUU, but I just rebooted and ran it as admin whilst not touching any other program in windows until it was done and it worked.
zoth said:
You have to choose. 2.0.0.8 HSPL
Click to expand...
Click to collapse
I believe you are to choose 2.08 to install HSPL
And you choose 2.08.0000 when you want to uninstall HSPL, for warranty and such.
well i had done a hardreset before but nothing, i tryed it on my laptop and it worked fine, guess it was my PC =/, thanks anyways to all you who tryed to help.
S3BAZ10 said:
well i had done a hardreset before but nothing, i tryed it on my laptop and it worked fine, guess it was my PC =/, thanks anyways to all you who tryed to help.
Click to expand...
Click to collapse
Please change the Thread title by adding {Solved} or something like that to note that your issue has been resolved.
hi guys, I tried all of hspl2 (1024) version for TMO US htc HD2 but it does not work at all. Pls help me.
Critical error is showed up by hspl2
My Phone softare information;
OS 5.2.xxxx
Manila 2.5.xxxxx
Rom v 2.10.xxxx(82076) WWE
Radio 2.08.xxxxx
I still use stock rom which is TMO US's shipping rom
I checked whole Hspl2 (1024) but doent work, Pls help me,
Moved you over to General. HSPL questions should have been posted in the hspl thread already open buddy.
Peace,
Josh
ok. I'll do it. thank you
Related
I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....
try :
on the htc :
Start
setting
other
USB to PC
and enable faster data sync...
hope that help you.
Thank you I will try that now and will update in a few minutes..
NO still no good same thing again, it's a pain as it keeps leaving my phone in bootloader mode so I have to keep removing the battery...
tanzi said:
I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....
Click to expand...
Click to collapse
Hi
Step 1: Right click on SSPL and "run as administrator" it will be do the job.
If you get an error then Disconnect the cable and reconnect then run the Step 1 again.
Good luck
Thank you I will try that now..
It didn't work I did it twice but still the same, I am at my wits end with this arghhh....
tanzi said:
It didn't work I did it twice but still the same, I am at my wits end with this arghhh....
Click to expand...
Click to collapse
If you use a USB Hub then try use the usb port from the motherboard.
OR
Try to Install HSPL first. then Install any roms with Custom ruu. Please read the thread before you use them. They all explained here
http://forum.xda-developers.com/showthread.php?t=609477
Good luck
1) To install this HSPL there must be SPL 1.42.0000 on your device.
Otherwise the installation will fail!
To check your SPL version, hold the Volume Down button and do a reset.
It is possible to downgrade to this SPL, by just flashing to an Official ROM
with this SPL version.
Click to expand...
Click to collapse
For instance my is SPL 1.42.6666 and I have same problem.
Troubleshooting:
* I have SPL 1.42.666 on the device.... !!!! WAIT !!!! SPL 1.42.6666 is not the version of the SPL on your device!... it is the SSPL version. Most likely you have the needed 1.42.0000 SPL on the device, just try to install this HSPL if you need it. Don't worry, if there is not the right SPL on the device, then u will get an error message, but nothing will happen to your device
Click to expand...
Click to collapse
I had same kind of problem, I also run windows 7 I simply swaped to a different usb plug and then it worked fine. I was useing the plugs on the frount of pc's case so I wonder if the internal cable has a small problem or somthing as all other things work fine from that plug.
Hope that may help you.
Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...
tanzi said:
Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...
Click to expand...
Click to collapse
Wel done
If you want to uninstall the HSPL then follow this
Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Recommend any roms is not easy because it depends your usage pattern. Therefore read more in the LEO threads before you choose to download any rom.
Now you have HSPL therefore you can install any rom from here
Good luck
ALWAYS USE SEARCH FUNCTION HERE AND YOU WILL FIND ANSWERS.
Thank you for explaining everything in a way that I can understand, I am not very techy so understanding exactly what to do when written is very important so thanks again..
Hi Guys,
i have LEO SPL-1.66.0000
i am using HSPL2 and give me this Error:
Can anyone tell me why?? the phone works fine. oh its Telstra Next G Australia.
cheers
Why HSPL2? Try to use HSPL!
HSPL2 is better than HSPL its easier to use, works with spl1.66 and can be removed
Not certain what's causing that issue, can we see a pic of your bootloader (tricolour) screen ?
which device u have? (maybe it's T-Mobile 1024LEO?)
Run SPL and write here your ModelID (something like "PB811000").
I'm using right now Topix 1.5.6 Do I need to update HSPL to version 2. Is there any benefits?
Friend of mine had a phone with spl1.66. I just used an old rom to get the spl to 1.42 then just installed HSPL.
Works just fine, no issues whatsoever. Don't think HSPL2 has more benefits. Either way your phone is unlocked and if you mess up a rom flash, just use your sd-card to flash it anyway with hspl. Hope this helps.
Cotulla said:
which device u have? (maybe it's T-Mobile 1024LEO?)
Run SPL and write here your ModelID (something like "PB811000").
Click to expand...
Click to collapse
I'm having the same issue actually - identical error as well and a AUS Delivered HD2 (same as the OP has)
Phone is synced ok with WMDC 6.1
PB81110 HX-BC
SPL-1.42.000 XE
I'm using the first one in the mean time which works ok for this model.
mphoneclinic said:
Hi Guys,
i have LEO SPL-1.66.0000
i am using HSPL2 and give me this Error:
Can anyone tell me why?? the phone works fine. oh its Telstra Next G Australia.
cheers
Click to expand...
Click to collapse
I also experienced the same. But I solved it.
You can try the following (use Window XP SP3):
-unplug the usb connection
-reconnect, wait and see whether there is a pop up about the usb driver installation.
-there was a message asking whether to continue the installation, and just click yes
-at your device, choose connect using USB (instead of Active sync)
-then run HSPL2.exe
-choose 1.66 HSPL
-wait and you will see at your device screen "we hacked it"
-wait until finish, and this is very important, unplug your device before it boots, so it will not boot while the usb connected to your computer, if you are happened to boot while connected to usb, it will start syncing, and this will reflash your HSPL back to your stock SPL. I dont know why, but it was happened to my device.
Cheers
I'm now have 2.08 HSPL ...
Already a HSPL/HSPL2 thread. Why not post in there? Thread closed
OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Try running a task 29 and then run the HSPL again and install the 2.08 HSPL. Then flash MAGLDR then the ROM you want.
Edit: Sorry I momentarly forgot you have to have HSPL to do a task 29. Do this make sure your phone is in bootloader and plug it into the computer via USB cable and then wait until it says USB at yhe bottom in the white. Then and only then run the DFT HSPL again.
With Task29 also nothing happens. Same as with ROMS and HSPL, After synchro in ActiveSync, i have run TASK29, then my Leo goes into Bootloader and nothing happend. On Windows screen i have 0% progress bar, on HTC HD2 i see bootloader with USB status.
ERROR 302
EDIT: After clicking through recovery steps, Leo turned to showing Progres bar, but also stops at 0%.
RealWaaagh said:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.479.1
Click to expand...
Click to collapse
Just making sure: did you try to flash those stock roms over USB? Stock SPL's don't have the same protection that HSPL has, and can be overwritten by flashing over USB just fine.
Also: until you're sure you can reflash at least something, it might be better to stay away from task29
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
RealWaaagh said:
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
Click to expand...
Click to collapse
Hmm... If you can't get your phone to flash anything over either USB or SD, it does sound like your bootloader might be corrupted or something. That 302 error also doesn't sound good.
I guess if you have them you could try flashing using:
- a different pc/laptop
- a different SD card (perhaps a goldcard?)
*Probably* won't help, but won't make things worse either.
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
RealWaaagh said:
OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Click to expand...
Click to collapse
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens.
Click to expand...
Click to collapse
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
Click to expand...
Click to collapse
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
cancel this post
RealWaaagh said:
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
Click to expand...
Click to collapse
One more question are you right clicking and running HSPL as administrator???
samsamuel said:
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
Click to expand...
Click to collapse
I have already tried to start hspl4 without running WinMo, same effect. In WinXP Bootloader still displays on the Phone, and in DFT HSPL progres bar just bounce from left to right.
In Vista DFT HSPL returns critical error about connection.
About ROMS, 3.14 is East Europe (downloaded from HTC after checking serial) and 1.48 is WWE, also checked with serial from HTC site.
I have tried 1.48 EE since somewhere i have read, taht i have to get rom with the same number on the end, as installed (ie. 3.14.479."2")
PS. I can't tconnect to Mobile Center is Vista. With ActiveSync on WinXP there are no problems.
silverwind said:
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
Click to expand...
Click to collapse
My Phone is East Europe WWE (afaik).
I have installed SPL 2.08 onto HSPL 1.6 with DFT HSPL3.
Then i have installed 3.14 by USB. I don't know, why i still have SPL2.08 if you say i should't.
HR works fine.
In a minute i will check HSPL with internet turned off.
How to flash HSPL via microSD ?
Since i can't flash whole ROMs (maybe i have wrong ones, but they pass serial check on htc.com) from microSD (3 cards checked 2GB SD, 4 GB SDHC(don't work), 16 GB SDHC)
T-Macgnolia said:
One more question are you right clicking and running HSPL as administrator???
Click to expand...
Click to collapse
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
RealWaaagh said:
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
Click to expand...
Click to collapse
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
samsamuel said:
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
Click to expand...
Click to collapse
PROBLEM SOLVED
I needed to make another admin account in WinXP. And then use it by Run As (then choose this new account).
I don't know why it works like that, but it worked.
Just to give all informations.
After more testing, i detected my Computer problem. My USB ports were not working properly, and update of Motherboard BIOS helped (ASUS P7P55D). So, i don't know what was the exact issue of problems.
Can anyone help me please... I'm trying to upgrade the rom to the latest HTC HD2 rom for O2. I connect the phone via USB, sync it and then run the RUU program from HTCs website. The phone starts the process and boots the phone to the 4 colour screen and then to the black HTC progress screen and then it hangs on 0% for a few minutes until the utility finally tells me its lost connection with the phone (Error 262). I've done soft resets and hard resets. Disabled firewalls. Tried on another machine. Even ran the utility under XP SP3 compatibility. Still no joy. Can anyone help?? Thanks
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
T-Macgnolia said:
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
Click to expand...
Click to collapse
Thanks for this... i followed your instruction and used 2 different cables. No joy.
Anything else I can try that doesn't involved the device suffering a sudden impact with the nearest wall??
Cheers
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
mr_bacon said:
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
Click to expand...
Click to collapse
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
silverwind said:
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
Click to expand...
Click to collapse
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
mr_bacon said:
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
Click to expand...
Click to collapse
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
T-Macgnolia said:
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
Click to expand...
Click to collapse
Hi... Been away so only just got this reply.
The rom I'm trying to install is a stock rom update from the HTC website:
O2 (UK): 3.14.206.1
For the record, my phone is an O2 phone.
As for Bootloader? It currently says:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Hope that helps. Really bugging the arse off me this is.
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
samsamuel said:
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
Click to expand...
Click to collapse
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
mr_bacon said:
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
Click to expand...
Click to collapse
Ignore that..
Mate - you're a genius. Followed your instructions and it worked like a charm.
Cheers pal. You saved my brain
Erm, not sure how much more basic i can make it. (Ignore my descriptions, just follow the steps)
Power off, hold voldown,power on keeping voldown held,, see multi striped coloured screen, that's bootloader, you can flash from this screen.
First you should try without bothering to change the spl.
Enter bootloader and connect USB, run the 3.14 you downloaded. That's it.
If it doesn't work, try changing spl as in my previous post by entering bootloader, and instead of running the 3.14 you run hspl instead.
As for writing a guide, you already read the various "how to flash.." guides (there are several) and watched the (also several) YouTube guides before you even started this thread,,, didn't you? Didn't you?? If not then shame on you!
Post back and ill check tomorrow.
Okay, I've spent about a week trying to figure out why I can't get HSPL4 to flash 2.08.HSPL onto my phone (and subsequently MAGLDR 1.3, then SOME version of Android).
I'd like first to apologize to samsamuel if I missed a thread somewhere that addresses this issue - I know you've gotten frustrated with a lot of people asking the same questions over and over =/
So here's the problem... I have a WinXP machine running ActiveSync 4.5 that recognizes my phone. When I first got my T-Mo HTC HD2 a year and some change ago, I went ahead and used the SD card to run an old version of Android (executed from within WinMo 6.5). At some point it died, and I went on using WinMo 6.5.
I got fed up with it and decided to try and go the HSPL/MAGLDR route. However, when I sync up the phone (usb cable -> hd2 w/ActiveSync, Enable Data Sync unchecked) and run HSPL4, it finds the phone, reboots it into rainbow mode, tells me I have "SPL 2.08.0000 ||", allows me to select 2.08.HSPL, then hangs on the "Please wait while installing the HSPL. Do not touch the device!!" screen and just keeps scrolling the progress bar back and forth. I left this up overnight (~8hours) and neither the phone nor the progress screen changes. No errors, nothing.
I've currently got the stock 2.10.0 ROM on the device, but I've also tried the 3.14.0 stock ROM (SPL 2.10.000) to no avail.
Here's all of the info I can think of to provide...
T-Mobile HTC HD2, 16GB MicroSD, 576MB RAM
R: 2.08.50.08_2
G: 15.34.50.07U
D: 2.10.82076
Rainbow Road says:
PB81120 HX_B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Any help troubleshooting this would be greatly appreciated!
-Skye
SkyeDaemon said:
Okay, I've spent about a week trying to figure out why I can't get HSPL4 to flash 2.08.HSPL onto my phone (and subsequently MAGLDR 1.3, then SOME version of Android).
I'd like first to apologize to samsamuel
Click to expand...
Click to collapse
lol!
when I sync up the phone (usb cable -> hd2 w/ActiveSync,
Click to expand...
Click to collapse
Don't do that,, put phone into bootloader manually, and then run hspl,,, USB times out in the time taken to restart the phone into bootloader.
samsamuel said:
lol!
Don't do that,, put phone into bootloader manually, and then run hspl
Click to expand...
Click to collapse
Tried that as well, still the same result. =( It recognizes the installed SPL version "2.08.0000||", I select 2.08.HSPL, it goes to the "Please wait..." screen and then nothing happens. Progress bar animates indefinitely and phone just sits on rainbow screen (USB displayed at bottom).
I've tried with and without the MicroSD card and with/without the SIM card. Same result.
Any ideas?
SkyeDaemon said:
Tried that as well, still the same result. =( It recognizes the installed SPL version "2.08.0000||", I select 2.08.HSPL, it goes to the "Please wait..." screen and then nothing happens. Progress bar animates indefinitely and phone just sits on rainbow screen (USB displayed at bottom).
I've tried with and without the MicroSD card and with/without the SIM card. Same result.
Any ideas?
Click to expand...
Click to collapse
If you stay on the rainbow screen, please have a look if USB is indicated.
If so, unplug and plug again the cable. USB disappears and come again.
Try again..
SkyeDaemon said:
Tried that as well, still the same result. =( It recognizes the installed SPL version "2.08.0000||", I select 2.08.HSPL, it goes to the "Please wait..." screen and then nothing happens. Progress bar animates indefinitely and phone just sits on rainbow screen (USB displayed at bottom).
I've tried with and without the MicroSD card and with/without the SIM card. Same result.
Any ideas?
Click to expand...
Click to collapse
Taco123 said:
If you stay on the rainbow screen, please have a look if USB is indicated.
If so, unplug and plug again the cable. USB disappears and come again.
Try again..
Click to expand...
Click to collapse
yea fiddle with the cable to be sure its connected, but to be honest, rather than spend hours trying, find a 32bit machine to try it on, id lay 60:40 on it working straight away.
SkyeDaemon said:
I'd like first to apologize to samsamuel if I missed a thread somewhere that addresses this issue - I know you've gotten frustrated with a lot of people asking the same questions over and over =/
Click to expand...
Click to collapse
I genuinely laughed at that :')
Also, as far as I can remember there is no stock ROM called 2.10? And flashing stock ROM 3.14 should give you SPL 3.03 not 2.10
Nigeldg said:
I genuinely laughed at that :')
Also, as far as I can remember there is no stock ROM called 2.10? And flashing stock ROM 3.14 should give you SPL 3.03 not 2.10
Click to expand...
Click to collapse
(and to think ive been trying hard not to bite lately, , , hehe)
2.10 was the original t mo, with spl 2.08.0000, 2.13 has 2.10.0000, and the tmous seems not to require spl 3.03.0000 to run 3.14, while the regular runs bad and loses ram when it uses 3.14 with any other spl than 3.03.
If so, unplug and plug again the cable. USB disappears and come again.
Try again..
Click to expand...
Click to collapse
Tried that. Unplugging the USB cable switches the indication to "SERIAL" and plugging it back in switches to "USB" again. I've tried two cables as well. It's not losing connection =/
find a 32bit machine to try it on, id lay 60:40 on it working straight away.
Click to expand...
Click to collapse
This is on a 32-bit install of WinXP =/
Also, as far as I can remember there is no stock ROM called 2.10? And flashing stock ROM 3.14 should give you SPL 3.03 not 2.10
Click to expand...
Click to collapse
I think I've been running in circles long enough trying to figure this out that I've thoroughly confused myself on how to correlate the ROM version and the SPL version, lol.
I guess I'll try another machine when I get home from travel, but so far still the same weird issue where it just sits there. Any other suggestions are welcome!
SkyeDaemon said:
This is on a 32-bit install of WinXP =/
!
Click to expand...
Click to collapse
heh my mistake, was thinking of another thread.
Thought of trying hspl3? hspl4 is only necessary if you are on 3.03.0000
There are even some threads talking about hspl4 possibly causing problems, even going as far as causing the 'unable to get into bootloader' and 'bad modelID' problems,, but i haven't really looked into that so couldn't say.
samsamuel said:
(and to think ive been trying hard not to bite lately, , , hehe)
2.10 was the original t mo, with spl 2.08.0000, 2.13 has 2.10.0000, and the tmous seems not to require spl 3.03.0000 to run 3.14, while the regular runs bad and loses ram when it uses 3.14 with any other spl than 3.03.
Click to expand...
Click to collapse
Of course, completely forgot that TMOUS had different stock ROMs, my bad. As samsamuel said, HSPL4 has caused some problems for some people (not for me as far as I know, but it has for others), so try using HSPL3 which I would think is perfectly fine for your ROM version and SPL version currently.
No luck on HSPL3 either - exact same problem. Just sits there and does nothing, no errors or anything.
Tomorrow I'll try on my Win7 laptop to see if it's some sort of strange driver issue =/
Went ahead and installed all the necessary drivers on my Win7 machine, synced up and HSPL3 worked on it. I'm guessing there is a device driver issue or something on my WinXP machine that is preventing HSPL from working.
I may look into it further at a later date to try and post a (real) solution to the problem in case someone else runs into this, but for now the problem is resolved. Many thanks to those of you that replied to help =)