Database Users

trying to install new rom error??????

I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....

try :
on the htc :
Start
setting
other
USB to PC
and enable faster data sync...
hope that help you.

Thank you I will try that now and will update in a few minutes..

NO still no good same thing again, it's a pain as it keeps leaving my phone in bootloader mode so I have to keep removing the battery...

tanzi said:
I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....
Click to expand...
Click to collapse
Hi
Step 1: Right click on SSPL and "run as administrator" it will be do the job.
If you get an error then Disconnect the cable and reconnect then run the Step 1 again.
Good luck

Thank you I will try that now..

It didn't work I did it twice but still the same, I am at my wits end with this arghhh....

tanzi said:
It didn't work I did it twice but still the same, I am at my wits end with this arghhh....
Click to expand...
Click to collapse
If you use a USB Hub then try use the usb port from the motherboard.
OR
Try to Install HSPL first. then Install any roms with Custom ruu. Please read the thread before you use them. They all explained here
http://forum.xda-developers.com/showthread.php?t=609477
Good luck

1) To install this HSPL there must be SPL 1.42.0000 on your device.
Otherwise the installation will fail!
To check your SPL version, hold the Volume Down button and do a reset.
It is possible to downgrade to this SPL, by just flashing to an Official ROM
with this SPL version.
Click to expand...
Click to collapse
For instance my is SPL 1.42.6666 and I have same problem.
Troubleshooting:
* I have SPL 1.42.666 on the device.... !!!! WAIT !!!! SPL 1.42.6666 is not the version of the SPL on your device!... it is the SSPL version. Most likely you have the needed 1.42.0000 SPL on the device, just try to install this HSPL if you need it. Don't worry, if there is not the right SPL on the device, then u will get an error message, but nothing will happen to your device
Click to expand...
Click to collapse

I had same kind of problem, I also run windows 7 I simply swaped to a different usb plug and then it worked fine. I was useing the plugs on the frount of pc's case so I wonder if the internal cable has a small problem or somthing as all other things work fine from that plug.
Hope that may help you.

Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...

tanzi said:
Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...
Click to expand...
Click to collapse
Wel done
If you want to uninstall the HSPL then follow this
Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Recommend any roms is not easy because it depends your usage pattern. Therefore read more in the LEO threads before you choose to download any rom.
Now you have HSPL therefore you can install any rom from here
Good luck
ALWAYS USE SEARCH FUNCTION HERE AND YOU WILL FIND ANSWERS.

Thank you for explaining everything in a way that I can understand, I am not very techy so understanding exactly what to do when written is very important so thanks again..

Phone stuck at white screen with HTC

Hi there,
I really need help!
I wanted to flash my phone with a nbh file, but I could not enter my bootloader.
I had installed HSPL3.
Now someone told me to use Flashaholic ROM update utility.
I did this, and a black screen with a % indicator appeared, not too long, it restarted, and went into a white screen with htc in the middle.
Restarting with volume down button pushed doesnt bring me into bootloader.
What can I do now?
I really need help!

Unfortunately, if you can't get your HD2 to boot into the bootloader, there's not much to be done.
Are you sure you had HSPL installed? Because from what I have heard, HSPL is there to always allow you to use it for flashing stuff, regardless of the integrity of other software parts such as the radio or the ROM, so reaching the bootloader should not be a problem for anyone.
Can you connect it to your PC via USB? If you manage to get a connection, you might just have a chance to flash another radio/ROM.

anrabi4 said:
Unfortunately, if you can't get your HD2 to boot into the bootloader, there's not much to be done.
Are you sure you had HSPL installed? Because from what I have heard, HSPL is there to always allow you to use it for flashing stuff, regardless of the integrity of other software parts such as the radio or the ROM, so reaching the bootloader should not be a problem for anyone.
Can you connect it to your PC via USB? If you manage to get a connection, you might just have a chance to flash another radio/ROM.
Click to expand...
Click to collapse
I installed HSPL3, and it said it was succesfull so...
After that I installed a custom rom with an utility that came with it (Dutty's)
So far I know, I cannot get any connection, but I try to download a stock rom (an utility exe) from HTC.com.
But I think this won't work right? because you have to sync.

You could try and flash a stock ROM via the SD Card, see if that works. There are some instructions here on XDA in the ROM Development section, check it out there.
Basically, once you have downloaded an official ROM from htc.com, extract it as if it were an archive and get the ruu_signed.nbh. Rename it to LEOIMG.nbh. Then take your SD Card, format it to FAT32, place the LEOIMG.nbh on the card and put it in your phone. While holding down the volume down button, boot the phone and a white Loading... screen should appear and the flashing process should begin.
I`m afraid this won't work either, as the bootloader is supposed to show up in order for you to be able to flash anything, but it's better than doing nothing, so...

anrabi4 said:
You could try and flash a stock ROM via the SD Card, see if that works. There are some instructions here on XDA in the ROM Development section, check it out there.
Basically, once you have downloaded an official ROM from htc.com, extract it as if it were an archive and get the ruu_signed.nbh. Rename it to LEOIMG.nbh. Then take your SD Card, format it to FAT32, place the LEOIMG.nbh on the card and put it in your phone. While holding down the volume down button, boot the phone and a white Loading... screen should appear and the flashing process should begin.
I`m afraid this won't work either, as the bootloader is supposed to show up in order for you to be able to flash anything, but it's better than doing nothing, so...
Click to expand...
Click to collapse
Does not work, still hangs in htc bootscreen.
What I have to do now? =(
I hope you have any more suggestions for me.
I will read it within 20 min, because I have to go soon for 20 min.
I really need my phone fixed =(

Hi, if I remember correctly, you already said in the Artemis-thread, that the VOL DOWN button is broken. If this is the case, I fear there is not much you can do...

Have the same problem too.
I've installed a few roms with no worries, tried one about an hour ago that performs a Task 29 and i'm also now stuck at the white HTC screen...
it says the task29 was succesfull and then got stuck on the white HTC screen and the rom failed to load as the laptop did not detect a usb connection...
I've downloaded a stock rom and put it on the SD card named LEOIMG.nbh and tried pressing the vol down button, the Red,green,blue,white screen appears i can see
PB81100 HX-BC
SPL 2.08.Hspl 8g XE
0x05
CotullaHSPL 0x30
Then "serial" at the bottom or if i have the phone connected to the pc then "USB" appears.
If i hold both buttons and perform a Hard reset the phone asks to press Vol up button then says restored really quickly then freezes at the white HTC screen..
Any suggestions
Cheers

Actually got it sorted now, the rom had the Flashaholic utility built in which i haven't used before.
As we speak the rom is now installing phew (stop sweating now)...
Thought i had bricked it...

MaxKaul said:
Hi, if I remember correctly, you already said in the Artemis-thread, that the VOL DOWN button is broken. If this is the case, I fear there is not much you can do...
Click to expand...
Click to collapse
It's not broken, it just worked before I did the task29.
The phone is empty, and has no bootloader, and no ROM.

wakers said:
Have the same problem too.
I've installed a few roms with no worries, tried one about an hour ago that performs a Task 29 and i'm also now stuck at the white HTC screen...
it says the task29 was succesfull and then got stuck on the white HTC screen and the rom failed to load as the laptop did not detect a usb connection...
I've downloaded a stock rom and put it on the SD card named LEOIMG.nbh and tried pressing the vol down button, the Red,green,blue,white screen appears i can see
PB81100 HX-BC
SPL 2.08.Hspl 8g XE
0x05
CotullaHSPL 0x30
Then "serial" at the bottom or if i have the phone connected to the pc then "USB" appears.
If i hold both buttons and perform a Hard reset the phone asks to press Vol up button then says restored really quickly then freezes at the white HTC screen..
Any suggestions
Cheers
Click to expand...
Click to collapse
task29 DELETES the ROM. You NEED to install a ROM. A Radio-ROM should be installed automatically with task29. If this isn't the case, you need to install a Radio-ROM too. You can either install the HTC ROM or you can install a custom ROM like forum.xda-developers.com/showthread.php?t=612580
Suggestion: Enter bootloader -> connect USB -> install ROM with CustomRUU

MaxKaul said:
task29 DELETES the ROM. You NEED to install a ROM. A Radio-ROM should be installed automatically with task29. If this isn't the case, you need to install a Radio-ROM too. You can either install the HTC ROM or you can install a custom ROM like forum.xda-developers.com/showthread.php?t=612580
Suggestion: Enter bootloader -> connect USB -> install ROM with CustomRUU
Click to expand...
Click to collapse
Do I have to repeat it again? there is NO BOOTLOADER

joshoon said:
Do I have to repeat it again? there is NO BOOTLOADER
Click to expand...
Click to collapse
If you'd read the entire post, you'd notice, that I quoted the user "wakers", who seems to be able to enter bootloader.

MaxKaul said:
If you'd read the entire post, you'd notice, that I quoted the user "wakers", who seems to be able to enter bootloader.
Click to expand...
Click to collapse
Well im not able to.
I did a HSPL before then I putted a custom ROM Dutty's on the device.
After that I putten a Stock ROM on it again, and then I used Flashaholic, and after task29 it got stuck.

Well no bootloader means no HSPL which is good news for your warranty coverage..
Just go to HTC service and play dumb " uhm i was playing around websites with a flash game and uhm my phone uhm rebooted and is like stuck ever since in uhm HTC logo"
Now if the case for not being able to load the bootloader is a broken volumedown button, yeah ur pretty screwed, prepare to dive in ur wallet.

Were do you live? If you need help and there's one living nereby maybe we can help (p.e. a full battery) I live in the eastern part of the Netherlands (Overijssel) PM me if you can come.

On the Kaiser (my previous phone) I also had a problem I couldn't enter the bootloader anymore, but I can't remember why or what I did to recover it.
- If it was an allmost empty battery and recharged it?
- If I have used a special tool to connect?
I really can't remember.
If I read your story, I think you have loaded a corrupted NBH thru SDCard method, otherwise i think you cannot wipe your bootloader. Task29 only wipes the ROM area not the bootloader.
Have you tried to contact Bepe or Cotulla, cause i think they know everything about (H)SPL.
Otherwise you can start building a new house (you've got your first brick )

have you checked you battery connections, the middle one is notorious for getting bent out of shape at which point the battery will not charge and you can't flash you ROM.

chris2busy said:
Well no bootloader means no HSPL which is good news for your warranty coverage..
Just go to HTC service and play dumb " uhm i was playing around websites with a flash game and uhm my phone uhm rebooted and is like stuck ever since in uhm HTC logo"
Now if the case for not being able to load the bootloader is a broken volumedown button, yeah ur pretty screwed, prepare to dive in ur wallet.
Click to expand...
Click to collapse
I'm 100% sure it's not the volumebutton, and yes Im gonna play a bit dumb ofc, but I already have another story.
henk-jan said:
Were do you live? If you need help and there's one living nereby maybe we can help (p.e. a full battery) I live in the eastern part of the Netherlands (Overijssel) PM me if you can come.
Click to expand...
Click to collapse
It's costs a lot for a trip to there.
Btw, I tried a full battery too, didn't work. (I have two)
webpatrick said:
On the Kaiser (my previous phone) I also had a problem I couldn't enter the bootloader anymore, but I can't remember why or what I did to recover it.
- If it was an allmost empty battery and recharged it?
- If I have used a special tool to connect?
I really can't remember.
If I read your story, I think you have loaded a corrupted NBH thru SDCard method, otherwise i think you cannot wipe your bootloader. Task29 only wipes the ROM area not the bootloader.
Have you tried to contact Bepe or Cotulla, cause i think they know everything about (H)SPL.
Otherwise you can start building a new house (you've got your first brick )
Click to expand...
Click to collapse
I think it's bricked man, my bro is looking for the papers soon, and then im going to the KPN shop (the provider), because the phone has been ordered from there.
nrfitchett4 said:
have you checked you battery connections, the middle one is notorious for getting bent out of shape at which point the battery will not charge and you can't flash you ROM.
Click to expand...
Click to collapse
All the connections look fine.

[Q] stuck at white htc bootscreen

im newbie and just upgrade from hermes(my longest servant) to leo 512mb ,i accidently flash tmous radio, now i stuck at white "HTC" bootscreen. Currently
i run 2.08.hspl and still able to bootloader and connect to pc.
any idea how to solve my prob?
after a quick search as suggested in other thread, i try to run few steps which are:
1. run task 29 then install original rom.
2. run original rom micro sd
3. flash original radio rom
but still the same
any other trick/idea?
*sorry for my bad grammar

sponges said:
im newbie and just upgrade from hermes(my longest servant) to leo 512mb ,i accidently flash tmous radio, now i stuck at white "HTC" bootscreen. Currently
i run 2.08.hspl and still able to bootloader and connect to pc.
any idea how to solve my prob?
after a quick search as suggested in other thread, i try to run few steps which are:
1. run task 29 then install original rom.
2. run original rom micro sd
3. flash original radio rom
but still the same
any other trick/idea?
*sorry for my bad grammar
Click to expand...
Click to collapse
regarding point 2: did you use the RUU....exe file or the extracted file and renamed it leoimg.nbh?
What I mean is: extract the original HTC ROM to your desktop with either 7-zip en, even, powerarchiver. You will then have a file named RUU_Signed.nbh. Power off device and take SD card out an insert to PC. Rename the RUU-Signed.nbh file to leoimg.nbh and copy to the root of your SD Card. Reinsert SD Card in device and enter bootloader screen (press and hold vol down key and then shorlty on/off button). Once you enter the bootloader screen, then the HTC ROM will be automatically installed onto your device. If this succeeds, do a hard reset afterwards for extra security.
Good luck and regards, Kuzibri

kuzibri said:
regarding point 2: did you use the RUU....exe file or the extracted file and renamed it leoimg.nbh?
What I mean is: extract the original HTC ROM to your desktop with either 7-zip en, even, powerarchiver. You will then have a file named RUU_Signed.nbh. Power off device and take SD card out an insert to PC. Rename the RUU-Signed.nbh file to leoimg.nbh and cop to the root of youy SD Card. Reinsert SD Card in device and enter bootloader screen (press and hold vol down key and then shorlty on/off button). Once you enter the bootloader screen, teh HTC ROM will be automatically installed to your device. If this succeeds, do a hard reset afterwards for extra security.
Good luck and regards, Kuzibri
Click to expand...
Click to collapse
thanks for reply sir,
yes i did exactly like u said, and it installed the rom, but it became worse when my 2.08hspl replaced by 3.30 spl, luckily i manage to get spl 1.48 then 2.08spl again.

sponges said:
thanks for reply sir,
yes i did exactly like u said, and it installed the rom, but it became worse when my 2.08hspl replaced by 3.30 spl, luckily i manage to get spl 1.48 then 2.08spl again.
Click to expand...
Click to collapse
So, now everything is working again? I think you meant SPL 3.03, instead of 3.3, correct?
regards, Kuzibri

kuzibri said:
So, now everything is working again? I think you meant SPL 3.03, instead of 3.3, correct?
regards, Kuzibri
Click to expand...
Click to collapse
no its not working, still the same.
oops my bad, its 3.03,

sponges said:
no its not working, still the same.
oops my bad, its 3.03,
Click to expand...
Click to collapse
SPL 3.03 means that you have installed HTC Stock ROM 3.14! Do me a favor and enter bootloader screen and send me the info that's in the left upper corner?
regards, Kuzibri

kuzibri said:
SPL 3.03 means that you have installed HTC Stock ROM 3.14! Do me a favor and enter bootloader screen and send me the info that's in the left upper corner?
regards, Kuzibri
Click to expand...
Click to collapse
sorry sir i forgot to write down the number,
but now its pb81100 ss-bc 2.08hspl

sponges said:
sorry sir i forgot to write down the number,
but now its pb81100 ss-bc 2.08hspl
Click to expand...
Click to collapse
OK, run HSPL2_RUN.exe and set it to SPL 1,66.000 and soft reset your device. Download form HTC's website the HTC's official 1.66 ROM with your S/N. Connect device to PC either with AC or WMC, without setting up your device (connect without setting up option). Run RUU1.66..... exe and this ROM should be installed on your device. See if this works, if yes contact me again about your future plans (ROM, etc).
regards, Kuzibri

kuzibri said:
OK, run HSPL2_RUN.exe and set it to SPL 1,66.000 and soft reset your device. Download form HTC's website the HTC's official 1.66 ROM with your S/N. Connect device to PC either with AC or WMC, without setting up your device (connect without setting up option). Run RUU1.66..... exe and this ROM should be installed on your device. See if this works, if yes contact me again about your future plans (ROM, etc).
regards, Kuzibri
Click to expand...
Click to collapse
will update later, internet seem slow right now.

sponges said:
will update later, internet seem slow right now.
Click to expand...
Click to collapse
OK, I'll wait. I'm not an early sleeper! You could also try to take another download link form HTC, sometimes Europe 1 is very much slower that the other options.
regards, Kuzibri

kuzibri said:
OK, run HSPL2_RUN.exe and set it to SPL 1,66.000 and soft reset your device. Download form HTC's website the HTC's official 1.66 ROM with your S/N. Connect device to PC either with AC or WMC, without setting up your device (connect without setting up option). Run RUU1.66..... exe and this ROM should be installed on your device. See if this works, if yes contact me again about your future plans (ROM, etc).
regards, Kuzibri
Click to expand...
Click to collapse
hi sir,
there is no 1.66 rom for india set (my s/n is india htc)..it was directly updated from 1.48 to 3.14
then i flashed with RUU_Leo_HTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship it stopped at 1% (invalid vedor)

sponges said:
hi sir,
there is no 1.66 rom for india set (my s/n is india htc)..it was directly updated from 1.48 to 3.14
then i flashed with RUU_Leo_HTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship it stopped at 1% (invalid vedor)
Click to expand...
Click to collapse
then use 1.48, you can leave SPL at 1.66 (or if you can set it to 1.48 is also OK)
regards, Kuzibri

kuzibri said:
then use 1.48, you can leave SPL at 1.66 (or if you can set it to 1.48 is also OK)
regards, Kuzibri
Click to expand...
Click to collapse
problem solved! i found out that mine is defected hd2, it cannot boot or hang when warm or hot. i have to take off the battery for 5-15 mins to cool it down then put it back, and my surprise it boot again. the radio is not the culprit.
time to get a replacement from htc.
thanks sir for your concern.

sponges said:
problem solved! i found out that mine is defected hd2, it cannot boot or hang when warm or hot. i have to take off the battery for 5-15 mins to cool it down then put it back, and my surprise it boot again. the radio is not the culprit.
time to get a replacement from htc.
thanks sir for your concern.
Click to expand...
Click to collapse
You're welcome, that's what we are here for!
regards, Kuzibri

Loading Stock Rom

OK, so i am trying to load the stock rom back on my old HD2 to send back to t-mobile.
My phone has a broken flex cable going to the bottom buttons so i cannot hit the power button.
I downloaded the stock rom from t-mobile and have it both on sd card and on computer.
I can boot the phone to the point where it wants me to load the rom from SD card, i just cannot hit the power button to accept.
So i tried to do it from the computer. when i do, it just hangs at 8%.
Does anyone have any idea how I can put stock rom back on it?

Hold your volume down button down while you power,on your HD2. When you see the multicolor bootloader screen come up connect your USB cable to the HD2 and computer. Wait for the Serial in the white bar of bootloader to change to USB then run the RUU for the T-Mobile ROM. After you have flashed the ROM download HSPL 4 (linked in my sig) and run it but select SPL 3.03.0000 when it asks what version you want to flash. When you are done runningvthe HSPL utility boot into bootloader again to make sure you have SPL -3.03.0000. If you do and you should ypu are good for warranty.

T-Macgnolia said:
Hold your volume down button down while you power,on your HD2. When you see the multicolor bootloader screen come up connect your USB cable to the HD2 and computer. Wait for the Serial in the white bar of bootloader to change to USB then run the RUU for the T-Mobile ROM. After you have flashed the ROM download HSPL 4 (linked in my sig) and run it but select SPL 3.03.0000 when it asks what version you want to flash. When you are done runningvthe HSPL utility boot into bootloader again to make sure you have SPL -3.03.0000. If you do and you should ypu are good for warranty.
Click to expand...
Click to collapse
This is what i am doing, but it just hangs at 8% no matter what..

bnd10706 said:
This is what i am doing, but it just hangs at 8% no matter what..
Click to expand...
Click to collapse
Which one the ROM or HSPL?

T-Macgnolia said:
Which one the ROM or HSPL?
Click to expand...
Click to collapse
I am trying to load the rom first. I cant boot anything. it just says update failed when i try to boot

bnd10706 said:
I am trying to load the rom first. I cant boot anything. it just says update failed when i try to boot
Click to expand...
Click to collapse
Have you tried flashing via SD card? Here is a guide on how to do this.
Also I recomend you flash HSL first as it might help.

How do i flash HPSL first? I cant get the phone into sync with it?

bnd10706 said:
How do i flash HPSL first? I cant get the phone into sync with it?
Click to expand...
Click to collapse
You don't have to have to be synced through ActiveSync you use HTC USB sync. Click on my guide linked in my sig and follow the instructions there on how to flash HSPL you will see what I mean.

I reloaded HPSL 2.08 and then tried to install the stock firmware via usb and it still hangs at 8%. I wonder if i try to install a different version?
I cannot boot from SD since my bottom keys dont work. I cannot click the call button to accept.

bnd10706 said:
I reloaded HPSL 2.08 and then tried to install the stock firmware via usb and it still hangs at 8%. I wonder if i try to install a different version?
I cannot boot from SD since my bottom keys dont work. I cannot click the call button to accept.
Click to expand...
Click to collapse
Don't you understand? You don't need the stock ROM, once you have the stock SPL you -should- be fine. Go to the tri-Color screen and download HSPL4 on your PC and run it and choose 3.03.0000 (not HSPL) and click next and it should flash. If you've done that then you're ready to send it off for warranty. No need for stock ROM. Just change the HSPL to SPL again which TMagnolia and I just told you how to do.

Oh yeah and you can easily get to the tri-color by plugging the USB in and holding the Vol down button.

Skellyyy said:
Don't you understand? You don't need the stock ROM, once you have the stock SPL you -should- be fine. Go to the tri-Color screen and download HSPL4 on your PC and run it and choose 3.03.0000 (not HSPL) and click next and it should flash. If you've done that then you're ready to send it off for warranty. No need for stock ROM. Just change the HSPL to SPL again which TMagnolia and I just told you how to do.
Click to expand...
Click to collapse
Awesome! Thank you, no I was not understanding...very new at this. Thank you!

Quick question to add... there is no rom on there at all now....do i need to install one for warrenty?

The green square still says "upgrade rom code error" please try again

They won't power the phone on to see if theres a ROM and if they do it'll boot to SPL in which case I'd say they'd flash a stock ROM. What green box?

Skellyyy said:
Don't you understand? You don't need the stock ROM, once you have the stock SPL you -should- be fine. Go to the tri-Color screen and download HSPL4 on your PC and run it and choose 3.03.0000 (not HSPL) and click next and it should flash. If you've done that then you're ready to send it off for warranty. No need for stock ROM. Just change the HSPL to SPL again which TMagnolia and I just told you how to do.
Click to expand...
Click to collapse
I think they do not have a stock ROM on the HD2 and I was stupid and did not realize they probably already had HSPL on thier HD2. So they are not good to go for warranty just yet.
At the OP try right clicking on the RUU and select run as administrator. Also try different USB ports too that might help.

Skellyyy said:
They won't power the phone on to see if theres a ROM and if they do it'll boot to SPL in which case I'd say they'd flash a stock ROM. What green box?
Click to expand...
Click to collapse
When you get the red green blue and white screen, the green section.
in the green section it says
Upgrade ROM code error
Please try again
If you just let the phone boot up, lit says "software update faild. please try again" on a black screen with triagle with a ! in it.

T-Macgnolia said:
I think they do not have a stock ROM on the HD2 and I was stupid and did not realize they probably already had HSPL on thier HD2. So they are not good to go for warranty just yet.
At the OP try right clicking on the RUU and select run as administrator. Also try different USB ports too that might help.
Click to expand...
Click to collapse
I am using the exe file that i downloaded off tmobiles site...is that what i should be using to flash?

Skellyyy said:
They won't power the phone on to see if theres a ROM and if they do it'll boot to SPL in which case I'd say they'd flash a stock ROM. What green box?
Click to expand...
Click to collapse
I would still try to get the stock ROM on the HD2 before sending it in cause I can assure you if they will turn the phome on and check the ROM and SPL. and if they have SPL 3.03.000 and not SPL 2.10.0000 they will say why iscthat cause it looks like they were tring to update the phone and sould not have SPL 3.03.0000. Then they will probably say they either did not preform the flash correctly or had un approved software on the phone and will not pass it as warranty.

bnd10706 said:
I am using the exe file that i downloaded off tmobiles site...is that what i should be using to flash?
Click to expand...
Click to collapse
Yes that is the RUU, right click it and select run as adminastrator, Skellyyy is right too you need to use the HSPL 4 Utility to reset your HSPL to SPL 3.03.0000 if you get the ROM to flash

[Q][HELP!] Cant install MAGLDR

Hello, i have serious problem,
I was running Android GINGER... and after one restart i god 1234.... FAILED bla bla
After that i went to MAGLDR and tryed to reflash another rom but no succes
MAGLDR froze!!!!
I did TASK 29 on it and it removed everything, after this i am UNABLE to install MAGLDR 133 or any other on my HD2. its a 576MB from UK, using it in CROATIA.
HAD T-mob WIN 6.5, Android 2.1, and above mentioned 2.3.3 ver.
ANY IDEA HOW TO INSTALL MAGLDR AGAIN???
HSPL is COTULLA 2.08 HSPL
Did i bricked it? can i undo?
p.s. i did hardreset, didnt work.
CAN I TRY RETURN SPL and how to return to stock so i can try WMO6.5 again?
HELP i am desperate! help, payed alot for this phone, i am broke now without phone!

calm down man we've all been there at some point,
ok if you wanna go back to stock go to the htc site and download a official rom,
does your phone turn on?
can you get in bootloader?
if you can does it say spl or hspl ??

ops
i am sure you havent been there.
I GOT HSPL 2.08 by beppe and Cotula
I,ve tryed official rom, it starts counting, but at approx 10% it stops and bar goes red, and triangle with exclamation point appears next to it.
I OFF:... F**** it UP. i am so screwd!
-phone does turn on, and goes to white screen, saying htc and nothing
-i can go to 4colour bootscreen, sayes SERIAL and USB after i connect
ty for trying to help me

white screen hhmm Radio - do you happen to know what radio you have flashed, if not go here http://forum.xda-developers.com/showthread.php?t=611787 chose say 2.15.50.14 down load it, i dont have micro usb on my phone no more so you have to options put phone in bootloader wait for it to turn to usb and run the ruu for the radio, or extract it find the .nbh file and rename it to LEOIMG.nbh pop it in the phone keep holding volume down till u get a grey screen and follow the instructions to flash the radio, and then try again,
you said you had android before? did you use cwm or clk so you can recover??
oh and by the way i nearly bricked my hd2 on release day so i no how u feel lol
EDIT = you can try and flash the stock rom and start again, by using 7zip to extract the official rom, find the .nbh file, rename it to LEOIMG.nbh also pop it on a micro sd card smaller than 8gig (just to be safe) boot into bootloader and follow through that way.

Demon_man said:
white screen hhmm Radio - do you happen to know what radio you have flashed, if not go here http://forum.xda-developers.com/showthread.php?t=611787 chose say 2.15.50.14 down load it, i dont have micro usb on my phone no more so you have to options put phone in bootloader wait for it to turn to usb and run the ruu for the radio, or extract it find the .nbh file and rename it to LEOIMG.nbh pop it in the phone keep holding volume down till u get a grey screen and follow the instructions to flash the radio, and then try again,
you said you had android before? did you use cwm or clk so you can recover??
oh and by the way i nearly bricked my hd2 on release day so i no how u feel lol
EDIT = you can try and flash the stock rom and start again, by using 7zip to extract the official rom, find the .nbh file, rename it to LEOIMG.nbh also pop it on a micro sd card smaller than 8gig (just to be safe) boot into bootloader and follow through that way.
Click to expand...
Click to collapse
i sayed i had android on cwm, i tryed recover but magldr crashed, and since then i have problem loading MAGLDR.
RADIO FAILED TO UPDATE, i tryed that version that you sayed but it goes to 100% then shows again that triangle with !inside. F***** i am loseing my mind!
Your way of upgrading rom wont work, gray screen shows for a glich of a second and dissapears to 4colour bootscreen.
I wish i died! i ****ed all up.
BTW i bought a phone in uk and on the back of battery sayes only serial numbers in this order:
S/N99HJY005-2
35412003-754967-0
no imei, no nothing else if helps.
i am dead, payed 500$ for it last year for this amazeing phone and now i ruined everything.

ok im with you on what you have and havent done, to me it sounds like a hardware problem if it wont flash, do you have another micro sd car you could use to try and go back to stock??
did you format the sd card first ?

Demon_man said:
ok im with you on what you have and havent done, to me it sounds like a hardware problem if it wont flash, do you have another micro sd car you could use to try and go back to stock??
did you format the sd card first ?
Click to expand...
Click to collapse
I get it , how to do GRAY FLASHING THING, but i got RADIO EROOR
SAYES:
00018003
LEOIMG.nbh - FAIL
RADIO_V2 - RSA Fail
Update Terminate
UPDATE FAIL
this happends when the bar gets to the 100%

do you have access to another pc mate with a different operating system from yours??
are you connecting phone via usb to the front or back of the pc?
have a read through this thread im reading alos
http://forum.xda-developers.com/showthread.php?t=618084

Take out the battery and keep the phone off in a very cool air conditioned room for a couple hours (maybe even the refrigerator).
Put the battery back in and flash stock again.
edit: hmm. Just read that other thread, yeah you may need to jtag it...but I'd still try the fridge thing.
Edit2: worked for this guy:
nschoot said:
Sorry, for not replying before...
I put my phone in a ziplock plastic back and left it in the fridge for a few hours (I think about 8 hours or so). Then I booted it and tried to install the LEOIMG.nbh file from SD card... I kept it in the fridge while installing the image.
And somehow, it just worked first time!!
The image (from the first post of this thread) is a US demo version of Windows mobile, but I was able to install the regular ROM from the HTC site after this - without the need to keep it in the fridge.
Click to expand...
Click to collapse

demon_man said:
do you have access to another pc mate with a different operating system from yours??
Are you connecting phone via usb to the front or back of the pc?
Have a read through this thread im reading alos
http://forum.xda-developers.com/showthread.php?t=618084
Click to expand...
Click to collapse
ok what i did dunno, but this is whats happened
downgraded to spl 1.42 or something,
started official ruu winmo 6.5 got an error, cellphone shut down and now it wont even turn on.
Ty for all the help, realy realy realy thank you !!!!
I am off to bed, tomorow i will throw my hd2 to trash can!

davor.klobucaric said:
ok what i did dunno, but this is whats happened
downgraded to spl 1.42 or something,
started official ruu winmo 6.5 got an error, cellphone shut down and now it wont even turn on.
Ty for all the help, realy realy realy thank you !!!!
I am off to bed, tomorow i will throw my hd2 to trash can!
Click to expand...
Click to collapse
Which stock ROM did you flash?

either you have a bad flash and its gone tits up or its bricked, either way someone will be here tomorrow when u return

Demon_man said:
either you have a bad flash and its gone tits up or its bricked, either way someone will be here tomorrow when u return
Click to expand...
Click to collapse
STOCK ROM:
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
IT WAS WORKING BEFORE!!!
i left batery out for a couple of minutes,and now it goes to 4 colour bootscreen,
BUT! I have another problem, 1,42.0000 works, but its SPL, and if i try to go HSPL 2.08 PROGRAM CRASHES on my comp.
This is so fu**** up. I would rather send to someone who knows how to repair this. anyone interested?
Lost my will to live with this phone. i am suicidal! (joke, don't call social services)

davor.klobucaric said:
STOCK ROM:
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
IT WAS WORKING BEFORE!!!
i left batery out for a couple of minutes,and now it goes to 4 colour bootscreen,
BUT! I have another problem, 1,42.0000 works, but its SPL, and if i try to go HSPL 2.08 PROGRAM CRASHES on my comp.
This is so fu**** up. I would rather send to someone who knows how to repair this. anyone interested?
Lost my will to live with this phone. i am suicidal! (joke, don't call social services)
Click to expand...
Click to collapse
That is the correct ROM.
you need to flash it via SD instead of RUU, that way it will put the correct SPL on your phone without you having to do anything from you computer.
edit: to clarify, flashing via RUU it cannot replace your SPL version, but if you extract that file, then move the NBH to the root of your SD card, then rename it LEOIMG.NBH, then go into bootloader, it will recognize it and ask you to flash. hit power to flash and it will restore to stock SPL, Radio, ROM, Boot Logo, etc.. you're good to go.

your phone turned off??? is your battery dead??

orangekid said:
That is the correct ROM.
you need to flash it via SD instead of RUU, that way it will put the correct SPL on your phone without you having to do anything from you computer.
edit: to clarify, flashing via RUU it cannot replace your SPL version, but if you extract that file, then move the NBH to the root of your SD card, then rename it LEOIMG.NBH, then go into bootloader, it will recognize it and ask you to flash. hit power to flash and it will restore to stock SPL, Radio, ROM, Boot Logo, etc.. you're good to go.
Click to expand...
Click to collapse
I have tryed that, thank you for your response, it went well, spl went to rom fitting, BUT,
WHITE HTC sigh on turn on, 3 RED LINES ON THE BOTTOM showing radio, and other stuff, but it constantly restarts, it wont load win 6.5. anyonne know why?

Problem with clk/magldr
was trying to flash my htc hd2 EUROP with hd2 toolkit v 4.2.0.1 i follow this steps
1-i power off my phone
2-I press in vol down button and power button in same time phone now was in 3 color mode
3- i press in task 29 on hd2 toolkit this erase my phone completely
4-then i press vol down button and power button in same time again
5- i click in clk repartition and choose 200MB
6- what happen is after all this steps my phone start with htc image blocked in white and green and i cannot boot in fast speed mode like usually.
obs, im using spl-2.0.8 HSPL by cotulla.
does anyone knows how to enter in fast speed boot mode without clk or magldr cause ive tried with these they dont work,..i just only can run wm6.5 that is .....i need help please

You are sure, you have installed a recommended radio rom?
You should use the radio rom 2.15.50.14.
Send from my Leo using Tapatalk