Bluetooth rSAP working (Skoda, Mercedes, BMW)

Bluetooth rSAP working (Skoda, Mercedes, BMW) - Touch HD General

Hi guys,
Just connected the HD to a new Columbus radio system using rSAP.
First of all, I am not the one who made the .cab file needed, I simply followed the instructions on this site, and fiddled around a bit:
http://briskoda.net/superb-ii/howto...us-rns510-using-non-compatible-mobile/131709/
Here's what I did to get it working:
1) Download the .cab files from the above mentioned thread
2) Install .net compact framework 3.5
3) Install the BT_sap.cab file, it will say installation failed, but just ignore that..
4) Using file explorer, find "SAP settings" in the windows folder and click it.
5) Go to start => settings => connections => bluetooth and turn on bluetooth and make your device visible.
6) Uncheck the authentication or password box, then check the box that says "remote sim acces"
7) Connect to the radio.
That's all folks
Hope it works for you, please write your findings here.

??
hermman said:
Hi guys,
Just connected the HD to a new Columbus radio system using rSAP.
First of all, I am not the one who made the .cab file needed, I simply followed the instructions on this site, and fiddled around a bit:
http://briskoda.net/superb-ii/howto...us-rns510-using-non-compatible-mobile/131709/
Here's what I did to get it working:
1) Download the .cab files from the above mentioned thread
2) Install .net compact framework 3.5
3) Install the BT_sap.cab file, it will say installation failed, but just ignore that..
4) Using file explorer, find "SAP settings" in the windows folder and click it.
5) Go to start => settings => connections => bluetooth and turn on bluetooth and make your device visible.
6) Uncheck the authentication or password box, then check the box that says "remote sim acces"
7) Connect to the radio.
That's all folks
Hope it works for you, please write your findings here.
Click to expand...
Click to collapse
Question :
What happens to your phone after you leave your car ?
With my diamond, the phone does not login to any network after SAP disconnects , I have to reset the device or turn off/on the phone from the communication manager :-(
Otherwise , it's working fine though
Claude

Garfield1970 said:
Question :
What happens to your phone after you leave your car ?
With my diamond, the phone does not login to any network after SAP disconnects , I have to reset the device or turn off/on the phone from the communication manager :-(
Otherwise , it's working fine though
Claude
Click to expand...
Click to collapse
I've got the same problem. It went away for a while and my phone reconnected normally. But recently I had to soft reset my phone and the trouble has started all over again.
Has anyone resolved this issue? I did manage to get it working earlier (but I don't know how), so there must be a resolution to it.

hermman said:
Hi guys,
Just connected the HD to a new Columbus radio system using rSAP.
First of all, I am not the one who made the .cab file needed, I simply followed the instructions on this site, and fiddled around a bit:
Here's what I did to get it working:
1) Download the .cab files from the above mentioned thread
2) Install .net compact framework 3.5
3) Install the BT_sap.cab file, it will say installation failed, but just ignore that..
4) Using file explorer, find "SAP settings" in the windows folder and click it.
5) Go to start => settings => connections => bluetooth and turn on bluetooth and make your device visible.
6) Uncheck the authentication or password box, then check the box that says "remote sim acces"
7) Connect to the radio.
That's all folks
Hope it works for you, please write your findings here.
Click to expand...
Click to collapse
Link doesnt work for me?

nljuggler said:
I've got the same problem. It went away for a while and my phone reconnected normally. But recently I had to soft reset my phone and the trouble has started all over again.
Has anyone resolved this issue? I did manage to get it working earlier (but I don't know how), so there must be a resolution to it.
Click to expand...
Click to collapse
Same here.I installed an Energy rom and connected the phone to car, after i leave the car, the phone doesnt turns on, just need to soft reset it.
On my Touch Dual, i had installed a BT_SAP.cab file, and worked perfectly, everytime i left the car, the phone turned the network on.
Still no solution to Blackstone ?
regards

Related

Sandisk 256+wifi HELP!!!!!!!!!!!!!!!!!!

Please help me make my Sandisk 256+wifi work on my XDA Mini.
All the time i want to enable the wifi i have to reset the deive then insert the card...after inserting the green light apperas but when i want to configure it byit's software by clicking on the antenna below the screen the device freezes so i have to eject the card then device backs to normal state.
Please help to have the latest driver or additional software and assist me to make it work..
Regards
ROM: 1.12 O2 Xda Mini

Hi:
I don't have one, but i went to www.sandisk.com and found this, before i bought the card:
http://www.sandisk.com/pdf/retail/wi-fi-sd-compatibility.pdf
Sorry mate, it is not compatible!
Only the version without memory..
Bye

Driver
It's compatible..cause in the list for MDA compact which is as same as XDAii Mini bith cards are compatible...
Still looking to find stable driver and solution
Regards

Mine Combination is working fine....
Using German 1.12 ROM and latest driver from sandisk.com
Stefan

Sorry you are right they are compatible! my mistake!
Good luck

Glad to hear at least one person can work with it..so how can i obtain your ROM?

Hi
I have the same problem a few weeks now.
Before it worked great no problems at all.
i have the latest drivers and using rom 1.11.00
Don't know what's happend why it doesn't work properly anymore.
grts leon

LumpiStefan said:
Mine Combination is working fine....
Using German 1.12 ROM and latest driver from sandisk.com
Stefan
Click to expand...
Click to collapse
You mean you don't have to reset your device for working with it?
will it be detected everytime you turn on your MDA?
Have it hanged ever?
So why mine doesn't work?

Hi
Remove the drivers from your PDA by going to start-> settings->system-> remove program. Select the entries for the Sandisk card and remove them. Soft reset your PDA and then try the drivers from the website for PPC 2003.
After the driver has been installed. Please do another soft reset of the PDA and then insert the card.
Here is the configuration that should be on your PDA. The bluetooth support should be disabled. Tap on the two arrows on the top of your PDA. go to settings-> click on connections and then the advanced tab. then Tap on the network card to connect to your access point (AP). AP browser will be grayed
out, This is normal as we didn't develop a utility for pocket pc 2003. Make sure you have the automatically connect to non-preferred network option checked. If there are no items listed in the wireless networks box you can add your AP by tapping on "Add new Setting" Type the network name for your wireless network. You can find this in the configuration of your router. After you enter the name make sure "connects to" is set to "The Internet" and then tap on the authentication Tab. If you are not using the wep key, you can uncheck the box for wep. If you are using it on your router make sure to set it exactly the way it appears on your AP. When you finished making all those changes please tap on OK that appears up at the top. IF your AP is on, and within the range, you should see connected next to it and the tower to the left of it will have a
blue ring around the top. If you see a red X on the tower and it shows unavailable you should check the following:
1-IS the AP on
2- Is it in range 3- are your settings correct.
Once you see the connected next to your AP you can tap ok twice and begin using your wireless access.
It works for me
Grts Leon

is Destinator 3.075 on Jasjar possible?

Has anyone managed to install Destinator 3.075 on Jasjar

Yes, try searching and you'll find your answers!

1. Copy across the "DestinatorApps" directory to the PPC manually using active sync instead of using the installer
2. Copy the "DestDll.dll" into the windows directory of the PPC manually using active sync
Now you have destator installed (almost) the DestDll.dll also needs to be registered!
3. to register the dll I used "regsvr_arm.exe". just copy it onto the device, and run then select the "DestDll.dll" to register it.
4. Run Destinator and active it with you licence code as you would have previously
i had problems with connecting the com ports on destinator....so i just followed these steps:
First you've got to pair your GPS.
Then go to the "COM" tab in the bluetooth manager
Add a new outgoing port with the GPS as device (use a free com port usually try every single port until it accepts it)
And then do this:
5. Copy the "DestinatorApps/Destinator/Destinator.ini" to your desktop
6. Open this in a hex editor and change where it says C.O.M.6 to the com port of your gps. Mine was Com4 so I just changed
the 6 to a 4.
7. Copy the "Destinator.ini" file back onto the PPC
steps 5-7 i dont know if this is necessary coz after i did these steps, i closed the destinator program and then ran it and the "GPS was found automatically"....but when u go to the gps settings on the destinator program its on COM 1....and COM 4 was not on the list......but i didnt bother trying to set it up as per instructions coz its already working for me......just another note, if u turn off your gps receiver while the destinator program is running and then turn on the receiver again ur not going to be able to connect to a gps satellite etc......u have to actually close the destinator program and start it again and it will again automatically connect ur gps......its a bit complicated trying to follow the instructions......but if u follow it properly it will work.......well it worked on my jasjar as well as my XDA II with WM2003SE.....good luck

yes, thanks hadn't thought of that....
of coarse I have tried searching, I have spent 3 hours doing so ... I have found lots of references especially to a post by believer... haven't as yet found the post which gives the actual full answer ...
found one which gave the ini mod for getting around the os check
-------
if anyone else is looking for answers that part is:
modify the [Platforms] section of C:\DestinatorApps\Installer\Console\Default.ini
add the line
P2577V351=ARM
-------
what I haven't found is the issue of the dll being registered.
Now that you have wasted everybodies time and had me write all of this, are you likely to be helpful and provide a link, (as you seem to know where it is) or are you more a smartass without a clue than a geovass.

Thank you irv777 nice to see someone with intelligence

no probs

davidberrysmith said:
Thank you irv777 nice to see someone with intelligence
Click to expand...
Click to collapse
You didnt search correct...
http://buzzdev.net/index.php?option...c=view&id=2529&catid=26&limit=15&limitstart=0

geovass, thanks for the link...
irv777, followed your instructions and the only thing I changed was to install from the consol and disconect the device when I got a error re registration of file. All the rest... Perfect.
Thanks again

Destinator on JasJar and regsvr_arm.exe
Can anybody please point me in the right direction as to find regsvr_arm.exe. I have followed all the directions so far and when I try run destinator I get a Destinator object creation error. The only thing I havn't done is the register bit, please.

here you go

Destinator turns off after some minutes
First of all, thank you everybody who gave instructions for the installation, of the Destinator specially for irv777. I followed the irv777 instructions and I could install the Destinator and configure the GPS perfectly. But I could notice that after using some minutes the Destinator, the screen of my Pocket PC turned off and when I turned it on again (using the light button), the GPS communication was lost because the GPS COM Port was changed. Does anybody have the same problem? Does anyone have any idea of what is happening in my case? I could realize that when I open the registry on HKEY_LOCAL_MACHINE/SOFTWARE/Apps/DestinatorApps of my Pocket PC it is different from the registry of the Pocket PC of my friend who installed the Destinator using the custom metodology (he doesn't have WM5). Is it the cause of that problem? If it is the cause how can I fix it? I don't know how to edit registry.

I havn't found any problems with it on mine. a possible work around for you might be to change the power and light settings so they don't turn off when you are using destinator.....
;-)
good luck

obviously i am doing something wrong here....
copy the destinator apps were in the ppc? i dont have enough memory eventhough my exec is recently formated (ppc 32mb free/destinator apps 36mb).
anybody?
edit: please mates.... i am leaving for a road trip in ten days and i could realy use a gps

Aussie topic - destinator cont'
hi guys,
I followed the instructions:
1. installed destinator on PC
2. copy all files (140MB) of them to the storage card
3. were trying to run ...\ARM\Independent\DestinatorApps\Destinator\Destinator.exe and got the error message described in the discussion
4. registered the dll in the windows directory...
now when trying to run the destinator.exe from the storage card I'm getting nothing (the screen flicker once)...
any ideas? any help would be appriciated.

irv777 said:
1. Copy across the "DestinatorApps" directory to the PPC manually using active sync instead of using the installer
2. Copy the "DestDll.dll" into the windows directory of the PPC manually using active sync
Now you have destator installed (almost) the DestDll.dll also needs to be registered!
3. to register the dll I used "regsvr_arm.exe". just copy it onto the device, and run then select the "DestDll.dll" to register it.
4. Run Destinator and active it with you licence code as you would have previously
i had problems with connecting the com ports on destinator....so i just followed these steps:
First you've got to pair your GPS.
Then go to the "COM" tab in the bluetooth manager
Add a new outgoing port with the GPS as device (use a free com port usually try every single port until it accepts it)
And then do this:
5. Copy the "DestinatorApps/Destinator/Destinator.ini" to your desktop
6. Open this in a hex editor and change where it says C.O.M.6 to the com port of your gps. Mine was Com4 so I just changed
the 6 to a 4.
7. Copy the "Destinator.ini" file back onto the PPC
steps 5-7 i dont know if this is necessary coz after i did these steps, i closed the destinator program and then ran it and the "GPS was found automatically"....but when u go to the gps settings on the destinator program its on COM 1....and COM 4 was not on the list......but i didnt bother trying to set it up as per instructions coz its already working for me......just another note, if u turn off your gps receiver while the destinator program is running and then turn on the receiver again ur not going to be able to connect to a gps satellite etc......u have to actually close the destinator program and start it again and it will again automatically connect ur gps......its a bit complicated trying to follow the instructions......but if u follow it properly it will work.......well it worked on my jasjar as well as my XDA II with WM2003SE.....good luck
Click to expand...
Click to collapse
Is the procedure similar if you have an embedded GPS?
I have a Mio P350 & want to put Destinator 3 on it, do you install the console on the PC first, if so what files & from where do you install on the PDA, & what do you install on the SD card?
Appreciate any help I can get, as the MioMap v3.2 is driving me crazy!

GPRS connecting once, then needs reset

Hi,
I've got an Orange M500, upgraded with the Imate ROM 1.12.00WWE - ever since I upgraded the ROM, I can connect to my Orange GPRS service fine, however, if I disconnect then try to reconnect again, the connection fails. I have to turn on flight mode, then turn on the radio again in order to get GPRS access.
I've tried upgrading to Radio 1.13.00, but still no joy.
Any ideas?

Mine does that and I have the original ROM. A bit of a pain isn't it.

Here's the fix
This was originally posted by Peter for the imate JAM.
I just installed it and it's working like a charm.
1. Download the older version of caller-id from:
ftp://xda:[email protected]/BlueAngel/CAB_Files/Caller ID/IA_CallerID_1.20_WWE.CAB
and transfer it over to your device. Any directory is Ok. I used ActiveSync to put it into the My Documents folder.
2. Remove the file IA_CD-Startup.exe from \Windows\Startup on your device.
3. Rename iacontacts.dll to something else (e.g. old-iacontacts.dll). This file is in the \Windows directory of your device but is hidden. However you can rename it using your PC. Open Windows explorer, and navigate to Mobile Device>My PocketPC>Windows.
4. Rename displayCID.dll to something else (e.g. old-displayCID.dll). Access it via your PC the same as for the previous step.
5. Soft reset
6. Run the CAB file on the device - just tap on it.
7. Soft reset.
That should do it.

I have the same GPRS problem too. However, the link you provided just asked for the password to access that ftp. Hey, acs540, do you know the password or do you have that CAB file? Thanks in advance.

usernameassword is xda:xda
The fix in this post seems to refer to caller id!?! I too get the gprs connection problem and have made it better with different roms but not found a sure-fire fix.
If anyone has a patch that fixes this, please post it!

GPRS now working
Hi,
Finally I tried, or at least halfway, After I removed the CallerID everyone is talking about my Qtek9090 now works flawless regarding GPRS.
This is very interesting that Caller ID software makes GPRS not working
Anyway, now I can start and stop GPRS several times, I have now toggled it 10 times without any problem.
Before I had to reset/toggle radio to make it reconnect after a disconnect.
Thank you all that has investigated this problem!
One last thing, Do you really need CallerID? :roll:
Br
Lars

I don't use Caller_ID, but Photo Contacts Pro.
Did you also try to change GPRS slot (Class 8 or Class 10) in GPRS settings?

XShell said:
I don't use Caller_ID, but Photo Contacts Pro.
Did you also try to change GPRS slot (Class 8 or Class 10) in GPRS settings?
Click to expand...
Click to collapse
Well, yes, I have changed to Class8 (4R1T), default was (I belive) Class10
Br
Lars

No connection to vista pc after wm6 update

Hi guys,
great work! Much appreciated!
Only one problem here:
After upgrading my ba to wm6 under vista (yes, i read _and_ understood the wiki) it is not possible to connect via usb/cradle.
I downgraded and upgraded again - with no errors at all. Nothing. Same Prob. I checked the wmdc-settings. usb-con is checked. Several soft/hardreset and reboots so far. When I put the ba in the cradle the usb-sound sounds and thats all. Not even a mobile device in the devicemanager...
H E L P !
A PPC with no sync is not good!
THX

see if your BA is set up correctly
1. using file explorer, click on windows/async.lnk
2. choose menu/connections/
3. tick on synchronize all PC's using this connection, and choose "USB"

when i try to locate the async.lnk it has - as every file in this folder - a memory-chip-icon. Taping on it brings a error screen reading:
Code:
async.asy##
The file 'async' cannot be opened.
(Clicking on the 'Album'-Memory-chip-icon starts 'Album'... crazy!)
So I clicked on the Acrivesync-icon under programs and checked the connection-settings. Everything fine.
Any more Ideas...

Jipiee!
I just reinstalled WMDC - and viola!
Pfft! That one took hours to figure out!
So - Thanks a lot!