Database Users

DIY scratch protection

I noticed the first scratch on the corner of my Jam today. Since electronics always take the most abuse on the corners, I devised a quick and easy way to protect the corners of my Jam while I'm in Europe for the next 3 weeks. Take electrical tape or clear satin tape and place a piece over the corners. Works best if you cut a slit in the tape so you can fold it around the corner without wrinkles. In all probability the device will land on its corners if dropped or take the most abuse on the corners if scraped against something. Thus, problem solved; I did it to my digital camera too. It doesn't look half bad on either device, and if you can't stand the black corners, just use clear tape. Any tape works as long as the adhesive won't stick to the advice after you remove the tape.

damn that's dead sexy :lol:

Damn! Why didn't I think of that????
Why don't you run the tape all the way round? I think it will look somewhat better!... :wink:

I'm sorry, but that has to be the stupidest looking thing I've seen in a long time. Why don't you just get a silicon case for about $10 off of EBAY? I mean, if you REALLY need electrical tape and that's all you can find...great. But just get a cheap latex or silicon case such as the ones from JavoEdge.com.
Do you put electrical tape on the front and rear bumper of your car too?

GHETTOOOOOOO

Just curious, what specifically do you expect to happen in Europe over the next three weeks that would necessitate such a precaution when you don't prepare against similar risks at home :wink: ?

hehehehe... Good point JPreston!!! :lol:

I don't get it! People seem to get very upset when they discover they scratched the ball mirror on the back of their JAM. Now we have a JAM covered in electrical tape. Should we all carry our devices in the original box? Or better yet never use them to keep them in pristine condition? I am not saying I didn't get a little ticked off when I found a nice big scratch in the corner after a small drop but come on! I think we're all getting a bit too precious. Anyway, to each their own.
Of far more concern is the gunk that gets on the screen from my face every time I hold the JAM to my head! I mean yuck! What the heck is up with that? Is there that much oil on my face??? I just washed it! I gave my phone to my friend the other day to make a call and his face left some sort of super oil on the screen that wouldn't scrub off for several minutes! Its gross and embarassing! I think we need some sort of face oil protector!

Does anybody have any idea for cheap screen protection? I think the prices are outrageous for the slices of film sold as protectors.

I use the cheapest of them all...
They are made for Palm devices and are sold on flea markets or "One Dollar" stores... :lol:
They cost $1 dollar the 12 Pack!
Just cut them to size and go!

scratch? i've droped my mini 2 times and got 3 dent edges. damn sad. The stupid casing they gave me is getting pretty loose. I put it on my belt.... so everytime i knock it seems that pouch just flings out. The screw and the plastic seems to have worn off.
I think i'm gonna go to a skinning shop to hide the dent edges.

try to buy a leather case for Nokia 7610. it fits.
You dont use that in the box lether case. It will easily fall of that tiny hook.
Wit the lether case of Nokia, it is mounted sideway into the belt by a leather that is sewed.
mine has never fallen. Even if it falls off the belt when you undress, the leather case is so stiff that it will not dent the mini.

@Emil...
Can you post a picture of your JAM in the Nokia case for us to see?

vmirage said:
scratch? i've droped my mini 2 times and got 3 dent edges. damn sad. The stupid casing they gave me is getting pretty loose. I put it on my belt.... so everytime i knock it seems that pouch just flings out. The screw and the plastic seems to have worn off.
I think i'm gonna go to a skinning shop to hide the dent edges.
Click to expand...
Click to collapse
Dropped mine on a concrete floor from about 1.5 meters and got a really ugly dent on one of the corners of the battery cover. The cover wouldn't even go back on!
Easy fixed though. Just took a plastic pen and pushed the dent out from the inside. It still shows a slight dent and small scratches if you look closely, but what the heck...

Anyone know of any metallic paint (model, SKU, UPC code) that I could use on my JAM? I rarely put on my seatbelt, and the one time that I decide to play safe, I scratch up the corner of my JAM. I'd never go "ghetto" as one person put it in the thread, but I'm sure there's something out there to match it up. Any ideas?

Get the jam off of your belt and put it in a proper car holder and you will not only protect it from getting scratches from your seatbelt, you will also get it charged while driving. And also one less reason not to wear a seatbelt that could save your life in the case of an accident.

Incidentally, can anyone recommend a decent car kit for the JAM? I want one I can mount with some amount of ease somewhere on the console... I don't like those ones that stick on the windscreen.

elyl said:
Incidentally, can anyone recommend a decent car kit for the JAM? I want one I can mount with some amount of ease somewhere on the console... I don't like those ones that stick on the windscreen.
Click to expand...
Click to collapse
www.brodit.com

Just don't order it from Expansys as all their product descriptions for Brodit are messed up. Does anyone know where else to buy Brodit because I still need the mounting clip for my car (Expansys kept sending the wrong one). Can you buy from them (Brodit) directly?
Thanks.

Case for fuze/touch pro for protection

I wanted to know if anyone had any good or bad experiences with clear cases like this one
http://www.amazon.com/AT-Fuze-Activ..._75?ie=UTF8&s=wireless&qid=1227055029&sr=1-75
I want to get a case that will protect the fuze from drops. I drop my previous phone the 8525 twice and because I'm in a city the first drop was on one of those metal grates and the phones edges got scratched up more than I would have liked and the second time was on a concrete side walk. Both times I was pulling out my phone from my case on my hip and lost grip. I was interested in getting a case that I can pull my phone from the top. That may help prevent me losing grip. But I still want to put something on the phone incase I loss grip again and drop the phone. And I was looking for something that will not put that much bulk or take away from the looks of the phone. If anyone has any suggestions or experence with cases or skins that I can put on the phone to try and protect it from a drop I would like to read about it

I had the boxwave clear case for my 8525, and it saved my phone several times. There were a couple problems though. For starters, the gaps between the plastic and the phone get covered in dirt, and you have to remove the case to clean it out. The case snaps on to your phone will little plastic tabs. If one of those breaks, part of your case will be loose.
However, I will certainly give the case full marks for protecting my phone. It survived drops, throws, smashes, and just about everything else you can imagine would happen if a 1 year old got a hold of your phone. So, if you don't really care about the phone getting dirty and whatnot, the boxwave case provides some good protection while adding a minimal amount of bulk to the phone.

I had a case similar for my HTC Tilt and I loved it, it saved my phone several times too and it has a belt clip which I loved! Also if you get that case they have it on eBay for cheaper... I believe it was $9.99 or something like that, I was looking earlier today and saw it on there but I bought a Hot Pink Rubberized one instead. But I like the cases, of course it's your own personal preference though. Hope I'm not too late with the eBay info though lol. Here's my search link, there are a couple cases for it.
http://cell-phones.shop.ebay.com/it...=m270.l1313&_odkw=htc+touch+pro&_osacat=20336

Search for the body glove case. It is rubberized, not the best looking of cases, but might protect it the best. I bought mine on ebay.

I bought the official AT&T 2-piece case for $29.99 (-30% FAN discount).
It fits, but tabs that hold it on make the phone seem like it's going to get stuck in a half open position.

I wanted to thank everyone for there suggestions.
NotATreoFan is this the case you bought at ATT
http://forum.xda-developers.com/showthread.php?t=446555
Because thats one of the options I was thinking of or the crystal case. I'm going to The ATT store to check it out.
How do you like your case?
Thanks

rrider77 said:
I wanted to thank everyone for there suggestions.
NotATreoFan is this the case you bought at ATT
http://forum.xda-developers.com/showthread.php?t=446555
Because thats one of the options I was thinking of or the crystal case. I'm going to The ATT store to check it out.
How do you like your case?
Thanks
Click to expand...
Click to collapse
That's the case.

$1.99 free shipping.
http://forum.xda-developers.com/showthread.php?t=450611

HTC Touch Pro Case Protection
For those of you who have a Touch Pro and have the Sprint included HTC brand case, you probably have the same gripe about it as I do. There is very little protection to the side of the phone as the OEM case has several gaps in it. Also using the case for a few weeks, the velcro begins to lose its hold and the case may not shut properly. I have customized my case to fix these problems and would encourage others to do the same. Here is what you will need:
-Small elastic material (available at any craft store or Wal-Mart!)
-3M double sided tape
-Velcro strips
-5 minute epoxy (Wal-Mart)
Directions: Cut a piece of elastic the same length as the open portion of the side of the case. Cut out small pieces of double sided tape and apply to the black cross sections of the case. Apply the elastic and cut to size. For the the velcro fix on the front of the phone, cut a strip of the velcro and fit to size on the front of the case. Mix the 5 minute epoxy and apply to the back of the velcro strip you just cut. Apply the velcro to the case and allow to dry (apply pressure to ensure a tight fit). Enjoy your case!

Can I wash and reuse factory screen protector?

That's pretty much my question. I read the thread talking about doing this with aftermarket ones, and wish I had read it before I applied mine. I got dust under mine. basically want to know if I can wash the one that came with the Fuze and put it back on, before I spend 20 bucks to have a new one shipped to me.

The short answer is "Yes"
Lukewarm water is a good place to start, and don't bother to try to get the "down" side (the sticky side) completely dry: just flap about a bit until most of the water shakes off.
Might find it works better if you have some non-greasy soap around - note that most of the soaps available today will leave their OWN residue behind!
Another handy trick for removing spots of DUST is to simply pick them up with tape. This technique is particularly worthwhile if your only complaint is a small number of dust spots that you can remove (with the tape) by only having to lift one corner of the cover.
Find that a microfiber cloth does a good job with the Exterior service of the screen cover, with a bit of "Safe For Coated Lens" cleaner sprayed on the cloth if the cover is particularly grimy....

Why would you when they only cost a few pence!!!!

I just use regular seetrough tape, apply it all around, rub it on tight, then pull it of. after that apply it imidiatly to the phone, otherwise it'll collect dust again.
water didn't work on mine.
@jim: you would because this is FREE, no trouble and no waiting for your products (some people can only order them online from other countries and have to wait a week (or 2) ). + I think the factory one is the best (I have a differrent one but I liked the factory the best)

Thanx for the help. I heard the factory one was the best as well, that is why I wanted to stick with that one. That being said, I was using my phone in the car the other day,(not whilst driving) and forgot I left it on my lap, and well got out. long story short I guess I'll have to order a new one anyway. the phone made it alright, just 2 small chips. lucky i had the screen protector on though. Any one know of any as good as factory?

I just put a Martin Fields protector on my Fuze and love it. It's definitely on par if not better than the factory one.

Have an Exim screen protector on its way, but don't expect to receive it until early (hopefully) next week.
Have also been pleasantly surprised by the included screen cover - but wish they had included a protector for the keypad area as well. At the moment, intent is to mount the Exim's keypad cover once it arrives and save the screen cover until ready to replace the OEM one.
Pricing on screen covers varies widely: have had good luck with Boxwave covers for my Axim, but am ready to try some of the less expensive options with the Fuze.

Mattijn106 said:
I just use regular seetrough tape, apply it all around, rub it on tight, then pull it of. after that apply it imidiatly to the phone, otherwise it'll collect dust again.
Click to expand...
Click to collapse
you can use the steam trick, go into a small bathroom and run the hot water until there is a lot of steam. This will drop the dust particles from the air, ensuring you don't get any dust on the screen or protector while applying.

bboyneko said:
you can use the steam trick, go into a small bathroom and run the hot water until there is a lot of steam. This will drop the dust particles from the air, ensuring you don't get any dust on the screen or protector while applying.
Click to expand...
Click to collapse
I hope you mean just the screen protector...
taking your phone in a steamy room is just stuipid

gbueh said:
I hope you mean just the screen protector...
taking your phone in a steamy room is just stuipid
Click to expand...
Click to collapse
im sure nothing will happen to your phone in a steamy room
unless condensation occurs inside the phone, you're fine
i have so many phones
i always bring them into the bathroom,
i just leave it on the counter
i have never had a broken phone due to steam

not a porn site ;-)
These are reasonable priced and offer excellent protection.
http://www.bestskinsever.com/servlet/StoreFront

it's awesome way to remove dust by tape so i tested it and success with me

Screen Protector

Can someone please tell me how to apply the screen protector that comes with the phone as it's just a large piece of clear plastic with no instructions how to physically attach it to the display!

It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.

It's a sticker that you stick on the screen. How hard is this?!

Just put it on. Work cleanly though, be prepared and do it right the first time.

Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out

I've now put on the screen protector that came with the phone, but it feels a little thin and flimsy.
I'd like to know people's opinion of other aftermarket brands of protector for this phone as I'd like to get something a bit better quality.

Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original

akash_84 said:
Same thoughts here too
I ordered a pair from HTC direct but I think looking at them now that I have them, they are the same as the originals so I will probably not bother using them
I also have the Brando version now - Not opened yet but I will open and apply it to my phone tomorrow evening - just need a dust-free environment to test it
Apparently, Brando boast they have the best protectors so lets see
It does feel a lot stronger than the original
Click to expand...
Click to collapse
Did you try this new Brando screen protector, and if so, is it any good?
Also, has anyone else had any experience of after-market screen protectors for this phone?

OK I applied mine today - sorry for the delay but I was just waiting for a time I could be patient !
I ordered it from HTCDirect as they are the only ones that had in stock
Recieved it promptly the next day so Kudos to them on that...also the guy I kept in touch with over email (Carlos if I remember correctly) was great and prompt in my queries.
My main query was - does it have the SAME fitment as the original bundled one.
As you know, the bundled one covers the entire screen including the slider for zoom and camera
The answer was Yes, it was exactly the same fitment.
So when I opened the pack, I was a bit annoyed as it was clearly NOT the same fitment! It's close however, but the top of the camera where on the HTC is all the way round with a small hole for the camera, the Brando one is in a U shape leaving the top bit of the camera open.
OK onto application
Just like all Brando protectors, it is protected by two covers on either end with clear instructions - pull one side BEFORE application and the other AFTER application
Once the dust was off the screen and the original protector...
I did just this - and after several attempts of lining it up - and I note, it is very EXACT in lining up. Slightly out and you will have more black on one side from the screen than the other.
Peeled it off, applied it and smoothed it out - the latter bit was hardly needed as the bubbles just vanished which was great.
At this state, the protector looked smoked a little and not as clear as the original one.
Once I was happy, I peeled the top part - noticed one bubble near the end where the label to peel was, smoothed it out and the protector was as clear as the original one.
First impressions:
It does feel MUCH more durable
It has a very slight and I mean SLIGHT smoked affect in that it is not 100% transparent as the original one but this shows how good it is potentially in strength.
Usage is fine, I can glide over it with my finger and stylus without any issues. The original was a finger print magnet but this seems to not stain with it which is great.
Now the downside....
I think HTCDirect sent me a slightly duff one. It has clearly got markings on the top (once the top layer was off) which look like impact marks.
It is very tiny - almost like what happens to a screen without a protector after 12months
I'm not too fussed but feel a bit cheated. Its no use removing it now as I would have no protector on it during the replacement stages - not to metion I would have to pay to ship back etc.
For now, I am ok with it but if it bugs me, I will throw it away and put the original one on (I ordered 2 extras from Clove who as usual, got it to me instantly, good communications and speed in delivery).
The clove one has no marks at all so thats an option.
Hope this answers some of your questions but to summarise your question
Is it stronger?
Yes it is
Is it worth it?
If you can get one mark free - yes it is
Benefits?
It's re-usable, stronger, washable, and I notice it does not let as much light reflect of it - something I had huge problems with in the sunlight with the original one where I could not see the screen - I am not exaggerating!
Downsides?
Where I got mine from, it has marks on it - something that might just force me to remove it and go back to the original one
Also the camera does not go in a O shape but rather a U shape

OK during the submit button, I realsed the marks and the U shape was bugging me too much
I knew it was a matter of time that gap in the U would get clogged up with dust that would eventually get stuck around the U bit
Removed it and applied the original one I bought from Clove... I have two so if it does wear down, I can replace it
I know from experiance that the original one in the box that I applied lasted fine up till now (a month now since I've had my TD2) so I dont doubt that it will be worn out - May not last as long as Brando's guarantee of it outlasting te device but that's fine given the price of the HTC ones.
Applied it without any dust getting trapped (the main reason I had to buy these and the brando one)
I found those marks were actually dust that was already stuck under the protective layer - whether this is HTCDirects fault or Brando during factory release - who knows but I think as a lesson, I'm staying away from both and sticking to the original stuff.
Hope you make the right decision either way - for now, a brando goes into the bin

akash_84 said:
Bend the corner of the big part slightly and the two parts seperate
The part that goes onto the backing bit is what goes on screen
start from the top and smooth it down
As mentioned, work in a clean/dust free environment!
I've done it many times but even this time round, I got fluff inside - just one spec thinking as it was brand new out of the box, it wouldnt have anything on the screen and so I wouldnt need to clean it !
In removing the protector to clean it out... I ruined it
Got my new Brando one the other day which feels a bit more stronger and durable but still clear so I'll be putting that on later tonight
And now I have a air can with me too so if I get anything in the way, I can blow it out rather than trying to scrape it out
Click to expand...
Click to collapse
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually - big mistake.
so trashed the original one and waiting for the new brando to put it on. being a former iphone-user, i must admit that the diamond2 screen is pretty sensible to scratches. i thought that i won't be needing any protection, but i already have a few small ones...so a screen protection is a must-have now.

Should have read this first
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?

You'll be fine using it while its there - just be annoying to see the dust specs!
I ordered a pair of the original ones in the end as I was not happy at all with the premium Brando one - the look, feel and visibility was terrible
Reason I ordered 2 of the original ones is I was hearing rumours before the unit was even released that the original HTC one was not durable and would need to be replaced after x amount of months - having had mine for 4-5 months now and with heavy usage, I can report back to say the first protector of the two is still on there - still very clean with no stylus/finger/nail marks and still as durable as it was when I put it first on.

arsenal84 said:
I should have read this thread before I tried to apply my screen protector. Straight away I had dust underneath the screen protector. Obviously I will now have to order some more protectors but will I be alright using my phone until they arrive? How delicate is the td2 screen?
Click to expand...
Click to collapse
From what other threads are saying the screen should be treated with care. Don't push it hard and avoid impacts. Don't stick the phone in your back pocket! Some people have experienced damaged screens even after a short time.

Shouldnt put any phone in your back pocket!
The number of phones I have to fix or write off because they have had severe pressure on them - ie: sitting on them has increased 5 fold recently.
And lets face it...the countries population are not getting any thinner/smaller!

eXelero said:
damnit, didn't pay enough attention to dust & co...so after i saw that i catched a few dust pieces under it, i've tried to get them out manually
Click to expand...
Click to collapse
I know it is not recommended. but I use a small drop of water on the screen before applying the screen, wiping the water as it is squeeze out. The water takes the dust with it.

Hi
I've applied mine that came with the Diamond 2 and after a few attempts you can't see it is there. Ironically I fits so well I almost want to put another screen protector on top of it so it doesn't become damaged and need replacing.
Anyway a tip. Working in a dust free environment is the key. A bathroom is a good place. I have a hepa air filter (for hayfever) and this removes dust really well so run that for a bit which helps.
With all the care in the world dust can get underneath, I had a few specs, and they tend to cause a small bubble as the screen screen protector can't fit flush. I found it very easy to remove them. Have some sticky tape handy, this can be used to lift up the screen protector from the corner. Lift it back up enough to get to the spec of dust, and using another piece of sticky tape dab the spec of dust off the sticky side of the protector, then lay it back down.
Regards
Phil

Hairs
Fru T Bunn said:
It has a peel away backing which is much thinner than the protector.
I struggled to find how this attached when I got mine and have since put hair and smudges on the sticky backing. Can't wait for the new ones to come online mid May.
Click to expand...
Click to collapse
I know what you mean I made an okay job of the one that came with it. The rubber case I bought of eBay came with one as well and made a right pigs ear of that. I think they need to be applied in a clean room
I've since bought some more off eBay so next time, I'm going to be a lot more careful!
Cheers, Rob.

I got 3 screen protectors with the original phone (2 of them as a gift). The first one was perfect except for a piece of fluff near the middle of the screen. I tried to remove it with a cloth(!!!) and ruined it. So I went for the second one, but at this stage the screen was not clean so I tried to use a microfibre cloth, which made it worse because it leaves even more fluff. I tried to fix it a few times and so now I have fluff inside, plus a bubble (the protector is a bit scratched) plus it doesn't stick properly on most of the sides and around the holes.
I am tempted to use the last one, but if I ruin it once more I am out of them. My biggest problem is how to clean the screen before sticking the protector. Will all the fluff come away when I remove the old protector? How can I clean the screen, knowing that the microfibre leaves fluff? Shall I blow with a can of compressed air?

I find magic tape is great for removing dust spots. Use the backing sheet to gently lift a corner then push the tape underneath to clean screen or protector as needed.
My favourite screen protectors are from Martin Fields. Really tough and easy to apply. Also, they are washable so if you do get a real dust problem you just take it off an run under the tap. Don't try that with the phone though...

OK. How fragile is the screen, really?

Hello everyone.
I got my HD2 a couple of weeks ago and as usual with new toys, am still taking some extra care with it. I had a Touch HD before that withstood quite a few bumps and two small drops. I saw people carying iPhones in pants pockets, back and front. Given that HD2 screen is significantly larger, how fragile is it, really? I usually carry my phones in jacket pocket, screen towards the body, without any case or sleeve. Do I need to take so much care for it or is it actually more resilient than it seems? Yes, I've seen the threads with broken screens. Anything can break, given enough force.
Any serious feedback is welcomed. Thanks.
Cheers, R

Well I have had mine since it was released in the UK and have had it in my right hand side front pocket in my jeans/trousers etc, sat on floors etc and all sorts and nothing has ever happened to it at all. Its a pretty tough screen I think, as long as when its in you pocket its not at an odd angle, I cant see any problems keeping it in there. I certainly have no problems.

Scratch test
There is a YouTube video of a scratch test of the screen of an HD2, its in foreign but gives a good idea of its screen tolerances (those of a nervous disposition may wish to look away towards the end)
http://www.youtube.com/watch?v=NcEaehKWr2s

Hmm I can only speak for myself and my HD2... but my screen has 2 (really small) scratches..
I think these are from a keychain or maybe a lighter in my pocket. I don't really know where the came from - but not from dropping it.
I would recommend to use a (thin - not that thick vikuti) foil to protect it against scratches.
--> Question: What would you recomment regarding a foil to cover the screen? I bought 1 Vikuti foil and really disliked it - it is sooo thick
Edit: I think the knife in the video would be able to scratch the screen... only a matter of right angle an pressure

I dropped mine on new years eve - drunk and the only thing i noticed the following day was that i had lost the backplate lol
Someone on here very kindly gave me a replacement.
Other than that - no scratches so far

Had mine three weeks, using front trouser pocket though I am very conscious of checking the pocket for keys etc first.
I have a full body invisibleSHIELD skin, and i'm extremely happy with it.
I've knocked it a few times on the edge of tables and chairs, once on the metal hand grip on a bus seat, and theres not a mark on it anywhere.

I have a screen protector that covers the entire screen, and carry the phone in my pants pocket in the leather case that came with the phone (I'm waiting on a holster from eBay).
The screen is in perfect condition, however, I did scuff the corner of the HD2 by dropping it (in its leather case) as I went to put it in my pocket coming out of a movie theatre...dropped onto cement.
: /

I use a screen protector and have a very nice silicone case for it that fits very snug, but I'm just being careful.
I believe that common sense is enough to keep this device from being damaged. As you can see from the linked video above, the screen is very resiliant, but it's not scratchproof. Also, why on earth anyone would put it in the back pocket of their trousers and sit down is totally beyone me, but people have done it (and probably still do), but they end up on here asking how to fix their damaged screen. (My advice to them is to hook up a flex capacitor to their car, drive at 88mph, go back in time to before they broke it and slap themselves round the face and say "STOP BEING SILLY!!!")
It's tough, but not unbreakable. Just treat it with respect, look after it sensibly, and DO NOT PUT IT IN YOUR BACK TROUSER POCKET OR FRONT SHIRT POCKET!!!
As the meerkats say... simples
(I hate those adverts, but I do like Back To The Future )

johncmolyneux said:
FRONT SHIRT POCKET!!!
Click to expand...
Click to collapse
Why not...I put it in there all the time?
So it won't fall out or...?

Spike15 said:
Why not...I put it in there all the time?
So it won't fall out or...?
Click to expand...
Click to collapse
lol - I've NEVER seen anyone on this forum say that that has happened to them <sarc mark>

johncmolyneux said:
lol - I've NEVER seen anyone on this forum say that that has happened to them <sarc mark>
Click to expand...
Click to collapse
Just making sure I wasn't missing something.
Personally I don't bend over when I need to get something on the floor et cetera...I bend my knees...I've heard that bending like that is bad for your back.

Spike15 said:
Just making sure I wasn't missing something.
Personally I don't bend over when I need to get something on the floor et cetera...I bend my knees...I've heard that bending like that is bad for your back.
Click to expand...
Click to collapse
Yes, and even moreso if you have a hernia! Good to see that xda is also responsible for good health advice too

I can't wait for mine to arrive next week. I can tell you from experience that the IPHONE has cracked 3 times in pocket when I put too much pressure. Apple does replace them on a regular basis. They allow for what they call a hairline. If it spiders they won't replace it but a hairline is within their tolerance and is common enough for them to replace it without question. That is how I ended up with a new replacement recently. I wasn't using the phone much but my HD battery died on site so I put the time into the IPHONE to use it. I squatted with the IPHONE in backpocket and CRACK. I probably should check my beltline while I am at it..
They replaced it and that worked out anyways as I am going to sell it. Keep my HD and Bold as backup.
The glass looks pretty solid and as many people reported it a good solid piece of hardware.

i keep mine in the case it comes with when i am carrying it around... any pocket really.
i just make sure i dont sit on it! lol
the screen itself is extremely resilient when it is out and in use.
I leave mine lying around all of the time out of the case and it still looks brand new.
I dont use any screen protector.

screen strength
being a kapasitive screen it uses a propper glass cover instead of ****ty plexi glass or resistive glass as most phones use, this naturally gives it a more scratch proof serface but makes it less resilient to actually breaking. like one guy said it all has to do with angle and preshure.. and abit of bad luck when it comes to screen protection i recomend invisiShield. they are nice and thin, VERY clear plastic so it doesnt disturb teh screen quality. and last but not least, the fabric its made of is teh same as teh stuff that they use to cover helicopter rotor blades with, so it comes with a 30 year waranty.

Thanks for all the replies so far. I suspected as much, but it sure is nice to hear other people's experience
Cheers, R

Impunitus said:
Thanks for all the replies so far. I suspected as much, but it sure is nice to hear other people's experience
Cheers, R
Click to expand...
Click to collapse
I had the same fear with its screen .. i posted a poll on the screen
see this
http://forum.xda-developers.com/showthread.php?t=618978