Related
Hi there, my phones screen will not work, my friend kept opening and closing they keypad quickly after which he gave me the phone back and the screen did not work!
The problem im having is that the touch screen dont work, nothin else is wrong, the screen is not cracked, jus that it dont touch sceen no more.
The bad thing is I put it on boot mode and erased the phone memory, and since the touch screen dont work i can allign the cross thing.
Does anyone know a way in which i could fix this?
Cheers.
pod8 said:
Hi there, my phones screen will not work, my friend kept opening and closing they keypad quickly after which he gave me the phone back and the screen did not work!
The problem im having is that the touch screen dont work, nothin else is wrong, the screen is not cracked, jus that it dont touch sceen no more.
The bad thing is I put it on boot mode and erased the phone memory, and since the touch screen dont work i can allign the cross thing.
Does anyone know a way in which i could fix this?
Cheers.
Click to expand...
Click to collapse
Mmmm. Tricky perhaps. A hard reset will either cure or leave you stuck. If you hard reset and the screen is indeed dead (touch wise) then you'll never get past the alignment stage. If the touch issue is software related then you would be sorted with the hard reset.
A gamble I think!!
However you are stuck at the moment so in a sense you have nothing to lose. If it ends up being useless then you are faced with a warranty (hopefully) repair otherwise some DIY though it's not entirely obvious what has broken/come loose - possibly just a ribbon connector.
Mike
Maybe the ribbon cable came loose on the LCD side?
myztikal47 said:
Maybe the ribbon cable came loose on the LCD side?
Click to expand...
Click to collapse
Yeah i think its that as well, i hard reseted it a few times with no effect, in the begining of the day, it could still reconise the screen taps around 2/3 times before it totally went dead.
Are there any tutorials on how to open it up to check the ribbon?
Thanks.
This maybe the hardware problem with the mainboard itself. I read about this on here a few times, most people had the get their phones exchange....
myztikal47 said:
This maybe the hardware problem with the mainboard itself. I read about this on here a few times, most people had the get their phones exchange....
Click to expand...
Click to collapse
Yes, I am equally unsure that this is just a simple loose connector. It may be, but it appears to be fine for a short while and only then goes off.
Like you myztikal47, I suggest going for warranty replacement if at all possible. Only if you have no warranty shuld you attempt a repair yourself - this is a notoriously ellusive fix and indeed I would say there is no 100% works for all answer. Certainly do not assume it's the screen - most probably it isn't and you'll waste your money.
There are dismantling links in this forum - but you'll find them on my small Hermes site http://michael-channon.spaces.live.com- go to the loose keyboard section and you'll see the links.
Mike
my 8525 had the same exact problem, and i swapped the LCD and still doess the same thing...
I dont know what the problem could be, and i dont have a warranty.
What could be going on????
Any 1 know where 2 find the service manual????
Jorge
[email protected]
mikechannon said:
Yes, I am equally unsure that this is just a simple loose connector. It may be, but it appears to be fine for a short while and only then goes off.
Like you myztikal47, I suggest going for warranty replacement if at all possible. Only if you have no warranty shuld you attempt a repair yourself - this is a notoriously ellusive fix and indeed I would say there is no 100% works for all answer. Certainly do not assume it's the screen - most probably it isn't and you'll waste your money.
There are dismantling links in this forum - but you'll find them on my small Hermes site http://michael-channon.spaces.live.com- go to the loose keyboard section and you'll see the links.
Mike
Click to expand...
Click to collapse
Ok my best bet is to take it to carphone, i got my screen replaced there a few months ago, think i still have a 1 year warrenty
Thanks for all your help anyways
Tytn Service manual
jblandon1024 said:
my 8525 had the same exact problem, and i swapped the LCD and still doess the same thing...
I dont know what the problem could be, and i dont have a warranty.
What could be going on????
Any 1 know where 2 find the service manual????
Jorge
[email protected]
Click to expand...
Click to collapse
Here you can found the manual
http://www.megaupload.com/?d=0GD472TP
Roby
The warranty for my HD is gone and I would probably need to change the touch screen digitizer myself, found these on ebay for ~60€, but does anyone know how to change them? Again, any help would be appreciated!
Originally:
HTC Touch HD, it has been a wonderful phone until now. I have encountered a wierd problem with the touchscreen.
First the touchscreen stopped working completely, after awhile it suddenly started working, at first it recognized some bits and pieces but now it recognizes every touch as normal, except..
It is very inaccurate and the "sum of inaccurity" seems to change depending on where I push the screen, the screen alignment option in settings does not fix this.
I recorded two videos to show this problem better:
http://www.youtube.com/watch?v=Xd1vjiHr2QU
http://www.youtube.com/watch?v=TynTTFIQJv8
Any help would be appreciated on how to fix this!
looks broken id return under warrenty did it get any knocks / drops? do you have insurance?~
spzero said:
looks broken id return under warrenty did it get any knocks / drops? do you have insurance?~
Click to expand...
Click to collapse
I have handled it with great care so no big knocks or drops. Ill contact the store about the warranty. Just wondered if theres a way how to simply fix this.
Just noticed, the screen works normally sometimes for one touch, then it goes back to the inaccurate **** :/
Im now guessing that some cable could be loose or something like that?
Have u tried recalibrating the screen? I can't remember exactly where I found it, but its in programs or settings somewhere.
Viba said:
...the screen alignment option in settings does not fix this...
Click to expand...
Click to collapse
Yes I have..
Anyway I RMA'd it now. Hope I get a new one
I can tell you from previous experience, HTC does NOT warranty touch screens. You mentioned "a store", so I hope they help you, because HTC will not. >sigh<
Seems a little unfair if they don't seeing as the HD is purely touch screen!
SomethingWicked said:
I can tell you from previous experience, HTC does NOT warranty touch screens. You mentioned "a store", so I hope they help you, because HTC will not. >sigh<
Click to expand...
Click to collapse
Hmmh, well the store probably sends it to some service center here in Finland that fixes HTC phones.
Indeed sounds very stupid if the warranty doesnt cover the touchscreen.
Perhaps my HD suffered from something else than a broken touchscreen, eg. mainboard or a chip that controls the touch screen. Who knows I'm just hoping it "passes" the warranty :|
Well... Had Hard-SPL on my touch hd and duttys 1.7 rom, so the warranty is gone
Didn't know they were so picky about it, they said it would cost 605€ to repair the screen. So now I should probably start looking for a screen digitizer on ebay and some help on how to change it... Already downloaded the service manual, but there was nothing on how to change the digitizer, could anyone here show me some light to this? Thanks.
I have dismantle my HD to see if there's any way to change only the screen (it's broken)
There's no way, as far as I saw. You have to replace LCD, tourch screen and screen. It's one piece and there's no way easy way to open it without break it.
You can find all of them for about 200E.
drabisan said:
I have dismantle my HD to see if there's any way to change only the screen (it's broken)
There's no way, as far as I saw. You have to replace LCD, tourch screen and screen. It's one piece and there's no way easy way to open it without break it.
You can find all of them for about 200E.
Click to expand...
Click to collapse
So there's no way I could replace only this?
http://global.ebay.com/Original_Digitizer_Touch_Screen_For_HTC_Touch_HD/310124432320/item
Another sad story // hopefully with a good ending
I kinda have the same problem as Viba and others. Sorry for the looong post. But decided to describe in more details my experience up to now, and hope you can help as well.
All of a sudden, I started having problems with the touch screen of the Touch HD. I started noticing that whenever I touched the Touchflo buttons, the phone vibrated. Soon I came to realize the if I touched in some spot, the phone recognized that I was touching lower, to the point that it could not recognize touches in the taskbar, for instance.
The united has 2 or 3 months max. It had some falls before and I do not really know who (or which one) was the culprit.
Tried this as fix: re-alignment, hardresets, Official ROM upgrade. Then I started reading and understanding that the problem was probably the digitizer ("nice to meet you").
I live in Brazil and the Touch HD is not expected be released here any time soon. So the few HTC service centers do not know how to fix it and do not have parts for it. And also, I bought mine from an auction site by some user who bought it abroad, with no warranty whatsoever. I am left alone in this.
I was very frustrated and eager to get my device running again. So I started looking for a new digitizer and also the tools to open my phone. The digitizer (just the digitizer, not the LCD screen) I ordered from an ebay shop in Hong Kong on Monday and is expected to still arrive sometime in this century (IF Brazilian port authorities do not mess up). The tools arrived yesterday.
I downloaded the service manual and said to myself, let's see if the digitizer problem is maybe due to a loose flat cable. Got to work and carefully disassembled the device as per the service manual. (I have to say that, although I try to be carefull, I always scratch, bend or mess something up when I do jobs like these. So I was afraid of cracking some plastic or worse and actually did some.)
Up to where the service manual show, it went incredibly very well. But that's the problem. The service manual guides you to disassemble the unit up to the point where you are with the bezel, LCD and digitizer in one piece.
But hey! I saw zillions of internet shops selling the bezel (actually, the hole housing, but with no LCD), the digitizer or other parts separately! What is going on?
So I started trying to unmount the bezel, LCD and digitizer. Tried several things. It got really late. I was impactient. So I tried splitting the digitizer from the LCD, by inserting a hard plastic aluminium tip between the digitizer and the housing. A very thin plastic kind of tape came out (at lest part of it). So I tried doing it more. No success. And then I put a very thin screwdriver between then (just enough to get an ulgy bent it the plastic housing).
When I had played enough with that puzzle, I gave up and began mounting everything back. The good part is that I was able to get everything back and the phone is working. Well, except for the digitizer.
First thing I did was to kidnap the wife's Nokia E71 I bought her last month and she is not using yet (she couldn't learn to use yet; well, she hasn't even tried it), because I have to have mobile access to my emails.
And I really started now to consider other alternatives. Will some user like me EVER be able to change just the digitizer? Is it even possible? If it is, I would like to give it at least another shot.
But I am also afraid that it could be another part which is in failure. I just don't want to spend more $$$$ in this. It would be better to buy another phone (and maybe not a complete touchscreen - gosh, I miss my Tytn II). I so regret being a gadget freak and not waiting a release in my country.
Shoud I send my phone abroad for a service center repair? My sister lives in Dubai and she may be able to help.
Should I give up my unit and seel the used parts in ebay?
Hope to hear your suggestions. Thanks anyway.
Viba said:
Well... Had Hard-SPL on my touch hd and duttys 1.7 rom, so the warranty is gone
Didn't know they were so picky about it, they said it would cost 605€ to repair the screen. So now I should probably start looking for a screen digitizer on ebay and some help on how to change it... Already downloaded the service manual, but there was nothing on how to change the digitizer, could anyone here show me some light to this? Thanks.
Click to expand...
Click to collapse
before doing this what about removing hspl and reflashing back a stock rom
change shop and you might, and i say MIGHT, be lucky
much better than screwing up the machine
Rafael K said:
I kinda have the same problem as Viba and others. Sorry for the looong post. But decided to describe in more details my experience up to now, and hope you can help as well...
Click to expand...
Click to collapse
Nice to know I'm not alone with this problem
Sucks that the digitizer couldn't be removed separately, would help alot if someone knew how to do this, if even possible..
crashDebug said:
before doing this what about removing hspl and reflashing back a stock rom
change shop and you might, and i say MIGHT, be lucky
much better than screwing up the machine
Click to expand...
Click to collapse
I have already tried with 3 custom roms and 2 original SPL:s with two original roms.
The Finnish law allows me to get my HD replaced if I could prove that the custom rom didn't brake the digitizer. Already sent some emails to the local repairstation for HTC phones here in Finland, lets see...
I run a repair center (US). I have not gotten curious enough to take mine apart, but if someone has a dead one to experiment with, PM me.
Broken digitizer glass
I have the same problem with the digitizer glass being broken. I have had the back off the phone and stripped it back as far as I dare, but the service manual just doesn't tell you how to replace the digitizer and glass only. Checked out youtube where there are many videos with instructions on how to replace the screens and digitizers on lots of different phones as well as the iphone, just nothing on the Blackstone yet.
Any one else found a solution or decent instructions?
Today I disassembled my HD too, found a loose screen wire but nothing else. Even when I attached it properly the screen didn't work.
Has anyone found out how to change the digitizer?
some info
Hello,
I am also have HTC Touch HD, and I am also thinking about replacement of touch screen and housing because of scratches. Here instruction in Russian
http://www.pdacenter.ru/razborka/htc-touch-hd/
step 24 is not shown on the picture, but there is mentioned that in order to replace screen you should push it forward from back side of the screen; also mentioned that screen is fixed with double sided tape (probably it is fixed to the touch screen)
Also, did you try to use any polish to remove minor scratches on the touch screen? HTC Touch HS has resistive screen and probably may be polished (in contrast to capacitive touch screen that has some coating).
All the best
Also, about this problem see
http://forum.xda-developers.com/showthread.php?p=3911326
You guys should be smarter! If you want to warranty exchange it, flash the normal SPL again and flash a stock rom!
hello guys
i have problem on my touch hd, first i drop it. second the touch become not in the same place and its happened again and now its not working at all and after along time of trying i found that the digitizer is can be removed totally from the phone and i need to press hard in the west top of the phone to make the touch work and some of my friend told me that this is the digitizer is gone and u need to get another one and i found many on ebay but all of them has yellow part at the back . i dont know haw to fix it and also i dont know what is the yellow part is is this the data cable??? and haw to fix it
thanks guys for lessening and any help is appreciated
bikaso said:
hello guys
i have problem on my touch hd, first i drop it. second the touch become not in the same place and its happened again and now its not working at all and after along time of trying i found that the digitizer is can be removed totally from the phone and i need to press hard in the west top of the phone to make the touch work and some of my friend told me that this is the digitizer is gone and u need to get another one and i found many on ebay but all of them has yellow part at the back . i dont know haw to fix it and also i dont know what is the yellow part is is this the data cable??? and haw to fix it
thanks guys for lessening and any help is appreciated
Click to expand...
Click to collapse
This my be helpful :
http://forum.xda-developers.com/showthread.php?t=596665
Hey guys, I have been so much frustrated about my htc topaz....till now it is working perfectly. Since yesterday all of a sudden touch screen stops working...with ballooning effect on screen ...previously ballooning effect was noticed before 3-4 days,but i did not pay attention on it as touch screen working at that time..
What may be the probable cause is it digitizer or lcd screen gone?
I have uploaded the pictures also..
That's the Chinese Diamond2?
If so I have the same problem with a Chinese phone... There is a part of the screen that's not working fine (like a balloon on the left side of the screen). I have to press really hard and press more to the side than it should be
I've already considered in opening the phone to try to solve the problem.
Does anyone already opened his phone with success? Any pictures available to help the task?
indresh88, sorry to use your topic but I think we both need the same...
I had the same problem, is very usual in this phone. the tecnical changed the screen.
luisitron said:
I had the same problem, is very usual in this phone. the tecnical changed the screen.
Click to expand...
Click to collapse
The problem is that my phone came from China... So I would have to send it there, and that's not an option...
rvrosa said:
That's the Chinese Diamond2?
If so I have the same problem with a Chinese phone... There is a part of the screen that's not working fine (like a balloon on the left side of the screen). I have to press really hard and press more to the side than it should be
I've already considered in opening the phone to try to solve the problem.
Does anyone already opened his phone with success? Any pictures available to help the task?
indresh88, sorry to use your topic but I think we both need the same...
Click to expand...
Click to collapse
no definately not...it's factory unlocked asian version...also it is t5353 and official stock rom.
by the way how can we differentiate between chinese and factory unlock phone?
have you solve your problem?
Hi, use some standard scotch tape or tesa film. Stick it over the affected area and peel the tape off. This should unstick the digitizer again, it did the job for me quite often...
Cheers
badari said:
Hi, use some standard scotch tape or tesa film. Stick it over the affected area and peel the tape off. This should unstick the digitizer again, it did the job for me quite often...
Cheers
Click to expand...
Click to collapse
Please explain that better? I only have to stick some scotch tape on the screen and peel it off?? I have a screen protector, so it's better to take it?
Thanks
indresh88 said:
no definately not...it's factory unlocked asian version...also it is t5353 and official stock rom.
by the way how can we differentiate between chinese and factory unlock phone?
have you solve your problem?
Click to expand...
Click to collapse
I have the T5388i dual sim.
I'm no expert on those phones, but I think an easy way to know if the phone is HTC or Chinese version is the front camera side (on HTC is on the right and on the replica is on the left)
Other simple way is if it's dual sim than it's not from HTC.
If I'm telling some mistakes please someone correct me.
Concerning the problem... it's not solved
rvrosa said:
I have the T5388i dual sim.
I'm no expert on those phones, but I think an easy way to know if the phone is HTC or Chinese version is the front camera side (on HTC is on the right and on the replica is on the left)
Other simple way is if it's dual sim than it's not from HTC.
If I'm telling some mistakes please someone correct me.
Concerning the problem... it's not solved
Click to expand...
Click to collapse
Well according to my research...If you have standard htc phone, you have device name t5353,no dual sim,htc written on left side and front camera on right side....
badari said:
Hi, use some standard scotch tape or tesa film. Stick it over the affected area and peel the tape off. This should unstick the digitizer again, it did the job for me quite often...
Cheers
Click to expand...
Click to collapse
it helped me quite good and temporery, but how to fix it permanently...?
replace the touch screen digitizer.
eBay have many of them...
I have replaced my cracked one last month.
Two fixes for the scotch tape issue
1. Always take along some scotch tape or
2. Replace the digitizer. This can be done faily easily, see some other posts.
Cheers
I've looked at ebay for the digitizer and I've found many... the question is if they work on my phone?
I have a DUAL SIM T5388i, can anyone point me the right digitizer?
I've tried the tape but didn't worked I don't know if I'm doing it right because I've noticed no diference.
Help me!
I also have this problem, It just stopped working. I was calling, 10 minutes later when i took my phone and tried to unlock it, it did nothing, when i connect my phone in windows 7 with mobile center, I installed SOTI pocket controller, to check if it was my screen, and it was because via pocketcontroller it worked good, but how do i have to replace the screen thing, and how does it work with the tape,,
Thanks
i also had the same problem. if im not mistaken it might be due to humidity ...
i might be wrong
is there any way to fix this without replacing digitizer.
by the way i have a TD2 t5353 htc original .
Workign Solution Till Now
Hello Friends,
I have TD2 mobile and today I had same issue. I was thinking it was because of the weather or some.
I remember it did happend several time before, but when I restart the device several time it does work. So I was ignoring.... But today it did not work.. looks like going toward end... So I did soft and hard reset without and that did not helped me.
So I switched off the mobile, "heated" the touch screen gently with my hand for 1 min and started the mobile again and it worked for me .
Not sure if this is a solution, but will work.
May be I will contact Service Center here in Hyderbad and see what is wrong here?
Hope this will help you all...
Thanks.
Well, I've solved the problem... changed the digitizer...
rvrosa said:
Well, I've solved the problem... changed the digitizer...
Click to expand...
Click to collapse
How much that costs you?
prabhat said:
How much that costs you?
Click to expand...
Click to collapse
Take a look at solonomi. That's the place I've bought it.
digitizer for t5388i
Hi, I want to buy digitizer for t5388i, but I didn't find it. I searched at solonomi, ebay, alibaba... Have you any ideas where to buy? Digitizer for t5388i is not same with other t5388 models. Here is picture:
imageshack.us/photo/my-images/263/digitizer2.jpg/
(sorry for incomplete link, but I don't have permision to add images or links)
Many thanks.
Hi all,
First of all let me appologise for my bad english.
I have a G1 and yesterday after i called someone the touchscreen stopped working.
Now I tried a few things to test if it was really not working
- flashed a new rom to see if it was the rom
- used a backup when it was working.
- Reset the phone.
Now I opened the G1 and noticed the Flex Cable has a little tear in it.
At first i thought that was the problem, but i dont think that cable breaks that easy if you make a phone call.
(I reassembled the phone and the lcd screen is working and all but no touchscreen)
So i was wondering, is it common of the touch screen just stops working?
And is there a way to test the touchscreen?
Many thanks,
MacWell
I'm sorry if i posted this in the wrong place or if this already has been answerd, but i couldn't find it with the search button.
not sure if this helps but if you have a screen protector, than remove it.. try cleaning the seams... not sure if it will help but i read a few posts saying it helped others...
ldrifta said:
not sure if this helps but if you have a screen protector, than remove it.. try cleaning the seams... not sure if it will help but i read a few posts saying it helped others...
Click to expand...
Click to collapse
Hi,
Thanks for the reply.
I do not use a screen protector.
I ordered a new G1 flex cable and I hope this will fix the problem.
However if it doesn't fix the problem I think i'll buy a new touchscreen for the G1.
But if anyone has an idea please tell me