No GPS Device - P3600 General

Hi guys,
Once more...i need your help please...
I have a Trinity running WM6 with no problems...
My TomTom version is 6.30 and everything is fine...
But today i've installed the 7.45 with new maps and...puff...
I always get the "No GPS Device" message...
Anyone can tell me what's wrong?
I've downgraded my TomTom version to 6.30 again but with the new maps it doesn't work...
I really need your help guys...
Thanks in advance...

Tom Tom 7 GPS configuration
Go to Tom Tom 7 GPS configuration and instead of internal GPS select NMEA
GPS settings:
gps program port: com1
gps hardware port: com9
baud rate: 9600

Hi Chaplan...
When i go to GPS Settings i have the GPS Baud Rate screen which i configured with 9600 and at the next screen i have this:
COM3:
GPS in COM9
COM7:
RIL on COM6:
S2410 IRDA
My question is how can i change the values?
When i tap in one of the above lines it just goes to the "GPS Status" screen again...
Thanks a lot for your help once more...

you just need to select gps in com9 and there you go....
Tom Tom says it has no GPS Device for 2 seconds and then says the GPS signal is weak till it gets a fix...

But i've already have GPS in COM9 right?
And TomTom stilles saying No GPS Device eternally

Hi again,
I think i understand now
By this time TTN7 change like you said Chaplan...i have now the message "Waiting for a valid GPS signal"...but it's been about 15 minutes...is that normal?
The Baud Rate is 9600 like you told me before...

And it's working
Thanks a lot for your help once more...

No GPS device!
Hi, Please help me!!!! I've just done a rom upgrade and unclocked my Orange M700.....When using TomTom6, It shows No GPS device!.....I tried the settings....but still no joy.
im currently using the following settings:
other NMEA GPS recieve....Selected
GPS baud rate...9600
COM3: GPS in COM9
COM7:
RIL on COM:6
S2410 IRDA
Please help......I'm going MAD!!!!!!!!!
Thank you

What's the P3600's correct baud rate?
Is a higher baud rate better?

Related

TomTom settings wont "stick"?

Hi, I have a HTC P3600 (Trinity), with the newest officiel ROM with GPS activated. I have TomTom 6.03 and I can get it working with a relatively quick fix (1-2 min).
I have chosen: NMEA reciver, Com 9 and 4800 baud - and everything is OK.
BUT when I start TomTom the next time, the com settings is wrong. It is listed as com 3, so it won't remember that it should use com 9.
The NMEA setting and the baud rate is corectly set.
Can I change something in the registry?
Thanks
Steen
If you have TT 6.03 one of the receiver options is "Built IN GPS" or similar, try that and see if it sticks that way
Thanks, I didn't even try the "build in GPS" as I have read that we needed to use NMEA antenna.
However, I followed your advice, and it sticks. Here you don't need to use baud rate and com settings.
Thanks for your help.
Steen

If you are having problems getting GPS working (TomTom)

Hope this helps someone else
Firstly here are the settings for GPS that get TomTom working on my HTC 3600i
Device - Settings / System / External GPS
Programs tab / GPS program port: COM4
Hardware tab / GPS hardware port COM9 / Baud rate 115200
Access tab / Manage GPS automatically (enabled/selected)
TomTom - Change preferences / Show GPS Status / Configure
Other NMEA GPS receiver / GPS baud rate 115200 / GPS in COM9
Make sure you have the a recent ROM installed (Windows Mobile 6 appears to connect faster than 5), some of the older ROM's for the 3600 don't have GPS enabled. I'm using the standard HTC 3.00.707.18. ROM.
Don't bother looking for a way to turn on GPS on the unit, this happens automatically, the only key here is to make sure that you have the correct settings & your device settings match up with TomTom.
Ensure that you are standing outside for GPS to connect, it may take up to 6-8 minutes for a cold sync (however should only take ~2 minutes).
To check if your GPS is actually working, go to show GPS status, if you see the message "GPS Device Not Found" it's not working properly, check the above steps again. If you see "No valid GPS signal!" this means your GPS is working, however not yet locked on-to satelites (you might also notice the blue and yellow circle spinning).
Hope this helps.
Cheers - Steve
Nice summary! It should be made sticky.
Just my 2 pennies: TomTom should be 6.03.
My config is: WM5, GPD1, COM9, baud rate 57600, and ticked "Manage GPS automatically".
ozsmac said:
Hope this helps someone else
Firstly here are the settings for GPS that get TomTom working on my HTC 3600i
Device - Settings / System / External GPS
Programs tab / GPS program port: COM4
Hardware tab / GPS hardware port COM9 / Baud rate 115200
Access tab / Manage GPS automatically (enabled/selected)
TomTom - Change preferences / Show GPS Status / Configure
Other NMEA GPS receiver / GPS baud rate 115200 / GPS in COM9
Cheers - Steve
Click to expand...
Click to collapse
hi steve,
my GPS works fine and i have baud rate set to 4800. will it be more efficient to set the baud rate to the highest setting 115200, like yours? what is the real different in baud rate, really? please comment.
sfaguy said:
hi steve,
my GPS works fine and i have baud rate set to 4800. will it be more efficient to set the baud rate to the highest setting 115200, like yours? what is the real different in baud rate, really? please comment.
Click to expand...
Click to collapse
Setting the baud rate to anything other than 4800 has no real effect as the amount of data being transferred is minimal.
For any version of tomtom prior to 6.03 you would set your TT preferences to "other NEMA". Version 6.03 and 6.032 automatically select "internal GPS receiver" so there is no need to change anything.
Thanks ozsmac...worked beautifully...
I can also vouch that this works for TomTom 5.21.
Cheers!!
Quick GPS FIX
Using Trinity, I use this proggy "BEELINE GPS" with this programme u get a real quick GPS fix .
get a look here :
http://www.visualgps.net/BeeLineGPS/
if u wanna the proggy, look on the net or if needed i can download it here.
Im having only gray dots on the GPS Status! and it still say, No Valid GPS, I did the settings as mentioned in first post. any help is appreciated ahhh one more thing, Im trying it on Athena, so am I on the wrong thread? sorry if I am

Gps port?

Hi,
would like to know which port is for the internal GPS system, I deleted the pre installed tomtom navigator and try to install tomtom navigator6.0 This program prompt me for a GPS port and I don't know which one.
Could you help me?
Hi,
this is what works for me:
WM5: port 4, speed 4800, internal GPS receiver
WM6: port 5, speed 9600, Other NMEA receiver
In the settings: same data and check "automatic management" (or the like, I
have an italian OS)
Hope this can help
Mauro
With AP Touch Rom 3.0 on Google Maps I have to choose port 4 with 57600.
pumats said:
Hi,
this is what works for me:
WM5: port 4, speed 4800, internal GPS receiver
WM6: port 5, speed 9600, Other NMEA receiver
In the settings: same data and check "automatic management" (or the like, I
have an italian OS)
Hope this can help
Mauro
Click to expand...
Click to collapse
via Settings->System->GPS I can select the com port on my T-Mobile Ameo DE
on TomTom you choose other NMEA receivers.
hi
in settings under external gps it asks for
programs .> gps program port ????
Hardware -> gps harware port -> i set it to com 4 57600
access - manage it autimatically is checked
and gps does not get any setting s in google maps
just says seeking sattleites ????
Hi.
In settings>system>external GPS:
GPS program port: WM5 -> com4, WM6 -> com5
Hardware : WM5 -> none, 4800, WM6 -> none, 9600
manage it automatically: checked
In TomTom (GPS status):
WM5: internal GPS, 4800, com4
WM6: other NMEA receiver, 9600, com5
These settings work for my device, hope it helps.
Mauro
On Google Maps and Delorme Maps I get "searching for satellite" when the settings are right, but it hasn't locked-on yet. When the settings are wrong, I almost instantly get an error message. So I'm guessing if you see "searching..." you have your settings right.
As for finding a signal, the achille's heel on this unit is locking on when you are inside (either a building or even some cars). Outside or inside my car it will lock on in 20-30 seconds, sometimes sooner. Inside my house or office it will fail 98% of the time. The sirf/star unit attached to my Palm will lock on inside my house - in the middle of the 1st floor - in under 20 seconds.
I think with all the trade-offs they had to make to get all 4 antennas to work together without interference, the signal strength on the internal GPS antenna got the short straw. I have top-notch strength on the cell and bluetooth antennas, so obviously they got top priority. I don't use wifi so I don't know how well it works, but the gps signal strength could use some work for the future X7502...
GPS, TomTom
I have a T-Mobile Ameo and recently I have installed TomTom Navigator 6.
when I start TomTom it takes between 5-20 minutes before it gets connected with a satellite.
Is this normal, or is there a problem..?
if not, what should I do to resolve this problem..?
grtzz,
Avicenna

Tom Tom 7 Internal GPS???

I have recently installed TT7 with the v7 map.
The thing is i can´t configure TT7 to use the built in receiver opion.
To make it work i have to manually configure the GPS reveiver in TT.
I use the black version of TT7...
Any workaround for this?
It's the only working configuration for p3600
- "altri gps NMEA" - com9 - 4800 baud -
I think that tomtom 7 is optimized for htc diamond and it has a different internal gps chip.
But working and this is good
4800 or 9600 baud???
I´m using 9600 baud, why do you use 4800?
I'm also using 9600Baud works fine here....
Actually this only occurs if you use the repack 3 of the original TT7 port (from Touch diamond).
I loaded this today as I had re-flashed my ROM and wanted to try the re-pack.
I have since gone back to the original port and TT7 doesn't need any set-up for the GPS receiver....it automatically selects the uilt in unit.
By the way....after a bit of research it turns out the re-packs were done for 2 reasons. One was to allow devices which were not on the original approved device list (hence they wouldn't load) and secondly to allow the use of maps aquired by other means.........
I am going to stay with the clean original........it works just fine for me....
Problem With Mine Too
ok i have:
TomTom 7 v.7.450 (9028)
map: iberia-13 v.720.1803
GPS settings:
gps program port: com1
gps hardware port: com9
baud rate: 9600
now i installed it perfectly, it opens perfectly
but now it dosent pick up any GPS signal
what should i do? any solutuion?
LAMM44 said:
ok i have:
TomTom 7 v.7.450 (9028)
map: iberia-13 v.720.1803
GPS settings:
gps program port: com1
gps hardware port: com9
baud rate: 9600
now i installed it perfectly, it opens perfectly
but now it dosent pick up any GPS signal
what should i do? any solutuion?
Click to expand...
Click to collapse
Which Tomtom7 version did you use? If you used the re-pack3 verssion you need to set the GPS receiver (in Tomtom) to Other Nema GPS.
If it is the standard Tomtom7 from the Kaiser thread it should find the internal GPS receiver without you doing anything.
finnaly working
ok
1º thank you Andych for giving me that hint
2º i whant to say that i had to change my WM version from
001TNYSXY - CE OS 5.2.19588 (Build 19588.1.1.4) WWE
to
Trinity WM 6.1 Diamond edition by Akeo V2 ---- v2 because v3 is off line still
and made some changes for ex:
took out:
TomTom 7 v.7.450 (9028)
and put in:
repack 3 of the original TT7
map: iberia-13 v.720.1803
GPS settings:
gps program port: com1
gps hardware port: com9
baud rate: 9600
and set the GPS receiver (in Tomtom) to Other Nema GPS
thank you all
i've tested 4800 and 9600 baud without difference so i use 4800 but 9600 works fine too.
Internel GPS
Work the internal gps with the repack 1 or 2 version???
I'm using TT7 v.7.450 (9028)
Other NMEA GPS
Baud Rate: 115200
COM9
Works perfectly, in fact seems to get a signal quicker than it did with TT6.
PS - Using ROM 007TNYSTD
I ve testet the black cap with the NMEA gps settings and is is very slow.
Then a reinstalled the black cap to the original tt 7 i have imediatly a signal with the iternal GPS.
The original TT7 is much faster than the black editions.
I got the black TT7 from this forum....
I didn't know there were other versions but it does seem rather slow.
Make My Day!, could you give me a link to the version that you say is faster than the black one please?
I mean that was the original CAP ( 1 link )
http://forum.xda-developers.com/showthread.php?t=401679
but you musst find the original (better) exe^^
I cant find it any longer. its delete from server where i find it.
Black repack edition: gps fix coldstart longer then 1 min only NMEA settings
original cap : gps fix very coldstart 5- MAX--> 10 seconds with Internal GPS
Ok well I'll try and find a version that isn't black then if that means I can get a quicker fix... Thanks for your help.
Make My Day! said:
I mean that was the original CAP ( 1 link )
http://forum.xda-developers.com/showthread.php?t=401679
but you musst find the original (better) exe^^
I cant find it any longer. its delete from server where i find it.
Black repack edition: gps fix coldstart longer then 1 min only NMEA settings
original cap : gps fix very coldstart 5- MAX--> 10 seconds with Internal GPS
Click to expand...
Click to collapse
Hmmm... a very rapid gps fix coldstart could be because gps are always active .... What is the battery life with the original cap?
are people dyslexic on here its original CAB not CAP
jojordy said:
Hmmm... a very rapid gps fix coldstart could be because gps are always active .... What is the battery life with the original cap?
Click to expand...
Click to collapse
No the GPS is off only you start tomtom it start too.
The Batary life is very long.
But the 1 start after insatll it can be that you musst wait for the signal becouse tomtom musst search the satelites.
Can't fin the TT7 original CAB
Can anyone give the link, or link here the original CAB so we can tast that?
Chaplan said:
Can anyone give the link, or link here the original CAB so we can tast that?
Click to expand...
Click to collapse
http://www.4shared.com/account/file/52017805/504b2906/ttn7.html

HTC touch pro and tomtom, strange problem

Hi,
I recently installed TTN 6 on my htc touch pro with US maps. Tomtom is able to locate and lock the satellites, and once it does that, tomtom behaves strangely. It shows the satellite location for 2 -3 seconds, and then for another 2 -3 seconds it shows "No GPS Device" and GPS is gone. Then again for 2 -3 seconds it shows the GPS location. This process repeats forever. I tested it for 30 min. The signal strength is almost full.
I have the following settings on the phone:
External GPS:
4800 Baud Rate / COM4
Tomtom settings:
Other NMEA Receiver
4800 Baud Rate / COM4
I have google maps installed too. It works fine with GPS with no such error.
Please let me know if something can be done to stop that annoying "No GPS Device"
Thanks in Advance
I have the exact same problem.
anjul_thegreat said:
Hi,
I recently installed TTN 6 on my htc touch pro with US maps. Tomtom is able to locate and lock the satellites, and once it does that, tomtom behaves strangely. It shows the satellite location for 2 -3 seconds, and then for another 2 -3 seconds it shows "No GPS Device" and GPS is gone. Then again for 2 -3 seconds it shows the GPS location. This process repeats forever. I tested it for 30 min. The signal strength is almost full.
I have the following settings on the phone:
External GPS:
4800 Baud Rate / COM4
Tomtom settings:
Other NMEA Receiver
4800 Baud Rate / COM4
I have google maps installed too. It works fine with GPS with no such error.
Please let me know if something can be done to stop that annoying "No GPS Device"
Thanks in Advance
Click to expand...
Click to collapse
Hi,
Is the COM4 the hardware port in your settings ? And which is the softwareport then ?
I use HW COM8 and SW COM6 BAUD 115200 ; TT set to use COM6 ... runs like a charm.
Dirk
Tomtom
haai there
You better use the built in GPS receiver. Your port and baut settings are oke.

Categories

Resources