Database Users

Himalaya loudspeaker-sound lost, headphone-sound ok

I lost the loudspeaker-sound in my Himalya. It works using headphones. I think it may have to do with another set of headphone I connected to it, which was not original. Perhaps it put the device on permanent headphone mode. But then again it might not have anything to do with that.
Is there a Himalaya expert in Berlin - Germany who might be able to help me with it? I dread having to send it to the official reapir center, as I expect it to cost a neck and a hand.

Happened to me when I received a call whilst listening to music. I pulled the headphones out before answering the call, and then answered it. I could here them but they cvouldn't hear me. If you plug the headphones in again and remove them it solves the problem. Well it did for me anyway

I tried that. I doesn't do it. It doesn't matter what kind of sound, if Media Player file is played of phone ringing, only the headphones work. I think I need a dotor.

I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out. Hereto:
1- What does that mean exactely? Which part is that, in what part in the on-board jack? If it had been bent out of place, is it possible to bend the part pack (at best without having to disassemble)? (I tried the ramming in and out, no go).
2- I looked at the non-original jack I had used and it is about 2 mm longer than the original. Might perhaps that explain it? Is there a part in the back that could have been bent out of place?
3- If indeed this was the problem (if the jack had been bent out of place, one way or another), would the microphone work? I can record using the dictaphone and the micophone also works during a call.

When we had himalaya's it happened to both of our devices (my wife and I had one each).
It appears the spring in the speaker can come loose. I used to bang mine (pardon the pun) on my palm and sometimes it would start to work. Then we broke the speaker protection shield, and this made it easier sometimes and hard to fix in others.
When I sold it, my friend took it apart as it was out of warranty, and as he is electrically minded, he find the dodgy bit, and soldered it to the device, and now works perfectly.

Yes! Thanks Jasjar. It worked after a bit of beating.
I found a detailed instruction of how to fix it permanently in another thread. Sounds complicated and dangerous but eventually I must do it.

ran2far said:
I have read a lot about the problem in others threads. It seems the headphone-jack can get stuck, not making a contact, which normally is being made and which turns the XDA back to speaker mode, when the headphone-jack is pulled out.
Click to expand...
Click to collapse
Sorry for kicking the topic, but this was the solution for me. I just poked in the headphone-jack with a little stick and tataaaa... my sound is back!

Sound lost problem
Hi all,
same happen to me, the sound stoped working (on my side it had nothing to do with the phone jack).
After the modifaication which is described in this forum i had still the same problem so i solder the loud speaker directly - still same problem...
After some time i flashed the device again, now it works, so on my side it was a software problem...
The device was 3 month out of power, but i think remove the battery and if the sound appears on startup (on first boot) but later not, then flash the os and it will work ...
kr
chw

XDA 2 sound problem...
Hi!
Plese help me!
I have strange problem with my XDA 2.
I bough it 2 days ago. It was in O2 network.
Now when I unlocked it for my network (polish ERA-GSM) I saw that when I'm calling I cant hear anything. Person from the other sight can't hear me too..
XDA have sound becose I used media-player ando other sound stuff, thats why I think that speaker is ok. Microphone is ok too becose I can record animations with sound.
So what should I do now? ;/
Plese help...

Just for reference:
A friend of mine had this 2020, and both Speakerphone and mic were not working.
When somebody called, the ringtone DID sound.
Anyway, bluetooth handsfree worked fine.
All we did was play with the jack, using the stylus! Not even headphones...
And now it works fine!
He says he'll never put phones on it again... lol
cu around!

Looking for more Info
Hi, please help me find which points in the MDAII Motherboard can I solder to disable the headphones and get the audio and mic back to the MDA.
After a while my headphone-jack is broken from the motherboard and now I only have the pin outs in it.
The device is working perfect, and I can use bluetooth headphones. I just don't have audio in the speaker and no mic without bluetooth.
I hope someone can tell me which of the red points en the picture can I solder to disable the headphones.
I just want to do this temporally until I get a replacement spare part for it.
Thanks
EDIT: 12-12-2007
I got it. Just joining 1 and 3 and you will get audio back to the PDA disabling the headphones jack.
Thanks anyways for reading this..

Did you find out what all the mboard pins are for the jack?
I have a dodgy jack and would like to take flying leads of the mboard jack to an external (easily changed) inline jack. Does any know what the 1 to 6 pins correlate to. I would like to still switch the audio via the external jack. Not bothered about the mic.
TIA.

No sound without headphones after fall!!

Hi all
It would be great if you shed some light on the problem
Xda exec had a fall!..since then no sounds at all, phone won't ring or won't play music...but has sound if i plugged the headphones in
Any theories/ideas what might have gone wrong...& possible solutions..
any help would be appreciated...thanxs

sound failed on xda exec
i also had the same issue but my handset was replaced as it was within 28 days of getting the handset
i never did manage to find the exact issue
when your handset fell did it have external sound / handsfree plugged in at the time
about the only thing that made any sense with mine was the possibilty of the micro switch / contacts of the externl audio jack being damaged
dont know if any of this info helps you at all but best of luck getting it sorted

Still no explanation for the no sound problem Xda Exec
Does anybody find out allready what's the problem with no sound on the Xda Exec.
I not speak about the problem with the external audio jack.
I can make cals like normal, I only can not play music or listen if somenone is calling me.
Thanks

its hardware problem with universals audiojack .. just open device ..remove board . plug headphones ... and see on connector /.... in most cases no sound issue cames from third pin of jack (thst pin detect plugged headpnones .. if it disconnected device plays in headphones if connected device plays on builtin speakers) if near end of it ...
a may advice you more deeply but i didnot have proper photo to explan in his basis..
just give me HI RES PHOTO OF BOTH SIDES OF YOUR MOTHERBOARD.. i explain what to do

mo3ulla said:
its hardware problem with universals audiojack .. just open device ..remove board . plug headphones ... and see on connector /.... in most cases no sound issue cames from third pin of jack (thst pin detect plugged headpnones .. if it disconnected device plays in headphones if connected device plays on builtin speakers) if near end of it ...
a may advice you more deeply but i didnot have proper photo to explan in his basis..
just give me HI RES PHOTO OF BOTH SIDES OF YOUR MOTHERBOARD.. i explain what to do
Click to expand...
Click to collapse
Thanks for your post.
You are shure that this willbe the problem, because I can make calls without the headphone. I was thinking that in the case that the connector gives the problem, I should also not be able to make any calls without using the headphone.
Anyway I was going to open my friend one day, to look what's up.

problem may be repaired in home in 10mins
you need
hands
brain
tools to open
1 needle
do photo .. i say what next

mo3ulla said:
problem may be repaired in home in 10mins
you need
hands
brain
tools to open
1 needle
do photo .. i say what next
Click to expand...
Click to collapse
Ok, here we go.
We have hands, tools ( a hammer ) and 1 needle.
I think I forgot something, but...
I think the problem, when the problem is hardware,
is that when you put the headphone jack, the top of the jack he opens the microswitch what you see at first.
Ofcourse when this switch he stays also open when you take out the jack, than you have a problem.
And yes with a needle you can first open the contakt and than you can dress littlebit the position of the contakt.
I have only 1 problem on my tel, this switch is closed as well, when I take out the jack. The problem is not this switch.

here we go

Correct, I am shure that this is almost always the problem.
In fact the switch is closed in normal position, and he goes open when you put the headphones.
When he not close as well automatic than, you have a problem.
But in my case it is really not this switch, so I am still looking for the reason why I not have sound.

hi all
i have same probelem like you
my friend using my device for weeks and when she give it back to me i have no sound from my device & even from headset i call the i-mate center the girl told me maybe your jack is dameged but when i sent it to suport center they told me your flex cable is dameged by wrong rotating your device and we haven't that yet ....
they sent it back to me and after some day my screen shows nothing then i buoght a cable from ebay an change , now i have voice sound screen
&....
like before
i hope these usefull for you

This was exactly my issue, under that pinkbox you marked is the tiny tab that makes or breaks contact with the internal speaker. Because my headphones break the contact, this tab after much use was stuck in the open position even after the headphones were removed. When I did the procedure you mentioned magically, sound..wow. I am extremely greatful for your troubleshooting skill.
Thanks a million mo3ulla.
If only i had this fix 2 phones ago..hahhahah.

lambrechts said:
Correct, I am shure that this is almost always the problem.
In fact the switch is closed in normal position, and he goes open when you put the headphones.
When he not close as well automatic than, you have a problem.
But in my case it is really not this switch, so I am still looking for the reason why I not have sound.
Click to expand...
Click to collapse
Hi lambrechts,
Did you manage to find out the reason?
i have the same problem, my device fell, but i didn't notice the problem until next day (i didn't use it) so i'm not sure if it is because of the drop.
I will open my device and check the Jack pins, but i want to know if you got any fix for this.

mo3ulla said:
here we go
Click to expand...
Click to collapse
hey mo3ulla, did your method work after repeated use of the headphone port? did it get stuck again any time after you fixed it?
just asking cause i have this problem on my 9000 and haven't opened it yet so i don't want to open and close it repeatedly
thankss

I have this problem aswell. But I inserted a fork and twisted it around a little and now it works as it should again.

Bumping this thread. Should be a sticky or in the wiki.
Anyways,
I tried the pin trick back when I posted here, it worked but it wasn't permanent. Instead I put a crumpled piece of post-it note above the pink dot in the picture and it worked, up until recently. Does anybody have a method to bend the connecter back down? I'm probably not using the needle right, I press the pink spot, but it pops back up.
Ideas?

twisting the pin really helps. thanks for the solution. I tried to insert my headphone again and the pin always stucked. I'm trying to find a permanent solution for this. Maybe put something to push the pin to be connected everytime I remove the headphone...

I hope this helps. I found it very useful to my Dopod 900. I tried to connect my headphones (sounds works on my headphone) then I disconnect it and sounds works on my stereo/speakers.
*Please do it carefully in pushing the pin upward from inside the hole. Just push it a little bit just enough to touch the upper pin..
additional tip: after you fixed your device, try to install SRS Wow for great audio experience

Quick Fix
I found that if you apply a little pressure between the base and just above the send key this seems to work, I tried this tonight and will report back if goes again.

luckyearl said:
Hi all
It would be great if you shed some light on the problem
Xda exec had a fall!..since then no sounds at all, phone won't ring or won't play music...but has sound if i plugged the headphones in
Any theories/ideas what might have gone wrong...& possible solutions..
any help would be appreciated...thanxs
Click to expand...
Click to collapse
could be a damaged PCB motherboard, or lose connetion for the sound chip!
you could try fixnig it, or replacing the motherboard.
a new motherboard could be bought off E-Bay US for a cheapish price =]

genspeed said:
I hope this helps. I found it very useful to my Dopod 900. I tried to connect my headphones (sounds works on my headphone) then I disconnect it and sounds works on my stereo/speakers.
*Please do it carefully in pushing the pin upward from inside the hole. Just push it a little bit just enough to touch the upper pin..
additional tip: after you fixed your device, try to install SRS Wow for great audio experience
Click to expand...
Click to collapse
Not sure if the srs wow will work, last time i tried it give lots of other problems like; mute the sounds, works great after you press the power button on and off, then no GPRS and Internet conectivity but if you have worked around those probs pls give an idea?

Problem with microphone volume when calling

Hi,
Since my Hermes fell off the table people keep complaining that they have problems hearing my voice while talking on the phone. They say the volume of my voice is too low. When using a headset everything's fine.
I've never had a problem like that, nevertheless I dismantled the Hermes to see if there was anything wrong with the microphone after the fall, but it seemed ok.
I also recorded my own voice using the voice recorder in WM6 to test the microphone and strangely enough my voice sounds pretty loud and clear to me.
After some googling I found that many people seem to have a problem with their voice barely being heard by other people on the phone.
Solutions I could not find and I do not understand why that problem has occurred after the Hermes fell down, as it seems to be software-related (otherwise my mic-test would have resulted in a low-volume recording, which it did not).
Has anyone here had that problem and found a solution?

Well, I've solved the problem, although not by the means I originally wanted to. I just did a recovery of a Backup from before the day the Hermes fell down and voila - everything works again as it should (although I still don't get it how the phone falling down can change the SOFTWARE, but hey, as long as it works).
Again we see the importance of regular backups.

I had this problem before. tried to fix it but didn't work. Flashed all sorts of roms, all didn't work. Even newly flashed roms still had this problem.
Headset is fine
but just speaking into the mic isn't.
Same as you, recording works fine too, but mic to phone just doesn't work. I am curious how did you dissasemble your phone though, do you have a manual or something?

I had this problem before. tried to fix it but didn't work. Flashed all sorts of roms, all didn't work. Even newly flashed roms still had this problem.
Headset is fine
but just speaking into the mic isn't.
Same as you, recording works fine too, but mic to phone just doesn't work. I am curious how did you dissasemble your phone though, do you have a manual or something?

Hi again,
Well, the problem's back again. Even after resetting the Hermes at first it worked fine, but later people complained again that my voice was too low. So it seems that the problem is first solved by resetting/backup recovery, but then reappears. Don't know how that is possible, but I fear that it is indeed hardware-related.
Has anyone any suggestions as to what I can do?
Am I right in assuming that the hole next to the one for resetting the phone is for the microphone? Because when I dismantled my Hermes the corresponding part did not look like a microphone at all. Here's a picture of what I am talking about:
Is the part where the black rubber-thingy (circled below) that easily falls off when dismantling is placed over the microphone?
As for the dismanteling, go there:
http://www.mikechannon.net/page1.html
and search for "Hermes", there are some nice guides there.
I appreciate any hints that could lead to me solving this problem.

Update:
I've been searching for corresponding Registry Entries and so far have found these:
HKEY_CURRENT_USER/Control Panel/Phone
Changing "Vol" to 65535 increased the mic volume a little bit, but it was still too low for being acceptable (I have been testing the volume by placing my Hermes next to my PC speaker while playing an audiobook at a normal volume and calling my landline as to see how it sounds).
See also here for the thread where I found this info.
I also found these two threads:
http://forum.xda-developers.com/archive/index.php/t-260171.html
http://forum.xda-developers.com/archive/index.php/t-256734.html
My Values at HKEY_LOCAL_MACHINE\SOFTWARE\HTC\AUDIOGAINx were originally at 18 and 19. I changed them first to AA and this did, or so it seemed, increase the volume more notably. Changing the Values to CC however changed little compared to AA (although this should make the mic even louder). I may be mistaken, but I even think that the quality was better with AA.
I am not familiar with the actual volume of the mic at the receiver's end, but in my opinion the volume was pretty ok. I will call a few of the people who have been complaining and see what they have to say about the volume.

Update:
I just called my brother and he said my voice was as low as before, so my modifications had no effect.
Next thing I will try is to totally disassemble my Hermes and put it back together so to check every connection that might have gone loose.

Update: Dismantled it totally (except for the screen part) - didn't help either.
Seems like there is no solution to this problem. Most likely I will have to get a replacement. This sucks.

HI
Exactly the same problem here.
(No phone audio but Note recording & Headset works fine)
Only the phone was not dropped. Just happened !
Did a reset but did'nt wok either !
Phones in great condition.
Like you though it was a Software Issue
How much was a new mic ?
Can it be economically soldered on ?
Is there no solution whatsoever ?
Please keep me updated
Many Thanks
Sampler100

Hi Sampler,
In the end I found no solution to my problem. Got myself a Vario III and am using that one ever since.
Please let me know if you find anything that can solve this.
Greets,
Cartman

Some of these problems (I don't say all) may be caused by damage to the mini USB port and the fine wires inside it. The port has wiring related to sound both earpiece and Mic. As you know connecting a handsfree headset cuts off the Mic and earpiece, so you can see that damage to the port or bend pins inside it can cause Mic problems. This may be why sound recording is fine, but in phone mode the Mic is cut off.
I say this only to avoid the assumption that the Mic is damaged (it may be), but it can also be the port and associated wiring that causes the problem. If you are dismantling check the solder contacts around the USB port for cracks and also for bent pins in the socket.
Mike

[Q] Headphone jack disable?

Hello,
I have a Problem with my Xperia X1.
The headphone jack is broken and the device will always return to the headset mode.
So I can not hear anyone during a conversation.
I would like to disable the headphone jack completely. Is there a program for that?

Are you sure it is broken?
Does it still deliver sound to a connected headphone?
Usually the detection of an inserted headphone plug is done via dis-connecting a contact in the socket where the plug is inserted (it re-connects when you pull out the plug). The same dis-connection will also happen if some dirt has accumulated at the place where this contact is, so it stays permanently dis-connected.
Over time dirt creeps into all holes of the devices and depending on your usage and storage style that may have happened now. Try to get that cleaned - maybe it helps.
I have however also seen devices where the connector of the socket to the PBA is simply ripped-off - no way to get that fixed afaik.
Luckily one of the wizards here (ultrashot) also has an X1 (as I remember) and he did a lot of true SW hacking to it, maybe he knows a way to intercept the driver or has a hint which driver to de-activate. Mind that he is very busy with really important stuff - so a simple hint may be the only thing you may get.

@ John Carter I have had the same problem for months now, at first it took a couple of mins for the headset icon to disappear after unplugged then it turned to hours and now days if I'm even lucky . I just found this today: HKLM/System/State/Hardware/Headset 0 .This disables the headset but for me it still does not play sound out the loud speaker like I hoped, in locksreen( I use S2u2) mode the headset icon is gone but when in the main interface the icon is still sitting on taskbar or topbar. It really sucks to have to use a mic headset connector to call and answer voice calls. I'm still searching for answer hopefully somethings comes up. Edit: It's a hardware problem not software.

First of all thank you for your answers.
@ tobbbie
The headphone jack is really broken = (
I've already tried to clean it but that dosent helped.
Thank you for your tip. I'm going to ask ultrashot maybe he can help me there.
@ Viper89
Are you sure it's not a software problem with you device?
For the headphone jack is not so important. I would unsolder him. But I do not know if that would still work.

I had also tried to play with the \status key in the registry with the same (non-) effects. I guess you have to intercept/kill the signal from the HW/driver that steers the other parts into what they do. Not sure where the HW signal enters the SW stack and if that could easily be altered (e.g. by dropping a device-driver). You could play with the HKLM\System\Drivers\builtin branch and then go for headset or alike. You may end up with a non-booting device, so take care to back up in case a hard-reset is needed.
If you are willing to play with soldering (and have some skills), try to solder the contacts of the socket new to the PBA. My guess is that the contacts have either come loose on top of the copper part of the PBA (then you can re-solder) or they have been ripped of the PBA including the copper. You then have to guess where the copper-lines went and re-solder. Worst you can un-solder all parts, but this is not easy to do without decent tools. You may bake the PBA around the socket and ruin the device fully in the end.

John_Carter said:
First of all thank you for your answers.
@ tobbbie
The headphone jack is really broken = (
I've already tried to clean it but that dosent helped.
Thank you for your tip. I'm going to ask ultrashot maybe he can help me there.
@ Viper89
Are you sure it's not a software problem with you device?
For the headphone jack is not so important. I would unsolder him. But I do not know if that would still work.
Click to expand...
Click to collapse
No it's definitively a hardware problem. I have actually stopped using my phone for music now and instead my mp3 player. I haven't seen the headset icon for 3 days now so maybe I'm in the clear. I think every time I kept plugging in my headphones to listen to music it kept re-aggravating the headset jack so I figured if I stopped using it completely maybe it will stop messing up and so far it has worked .

Microphone not working on Galaxy S5

My microphone on my S5 is not working. When I make a call I can hear the person but they can not hear me I also tried recording my voice and it didn't work, so clearly I am assuming the microphone is broken. What part do I specifically need in order to replace the microphone and have it working?

Sounds like you didn't do a search and read the existing threads on this subject. Your assumption that the mic isn't working may not be correct. You should at least try turning off the noise cancelling settings first, speaking closer to the mic, et cetera. There is also a service menu setting for microphone gain. Failing all of those items, then a warranty claim or buying the part yourself, if out of warranty.
All of these are elaborated in more detail in existing threads.
.

fffft said:
Sounds like you didn't do a search and read the existing threads on this subject. Your assumption that the mic isn't working may not be correct. You should at least try turning off the noise cancelling settings first, speaking closer to the mic, et cetera. There is also a service menu setting for microphone gain. Failing all of those items, then a warranty claim or buying the part yourself, if out of warranty.
All of these are elaborated in more detail in existing threads.
.
Click to expand...
Click to collapse
I have tried everything you have said before. If I could possibly know what specific part that is faulty so I can replace it because the warranty is expired

navpal said:
I have tried everything you have said before
Click to expand...
Click to collapse
It would have been helpful if you had bothered to tell us up front that you had done so.
The primary microphone is part of the charging port assembly.
.

fffft said:
It would have been helpful if you had bothered to tell us up front that you had done so.
The primary microphone is part of the charging port assembly.
.
Click to expand...
Click to collapse
Ok so replacing that part should fix the problem?

I was having mic problems. Remembered a friend having issues on his S3, he used a needle to clean rubbish out of the hole on bottom of the phone. So i did the same, very thin needle only pushed in a small amount, pulled a load of fluff out. Problem solved. Two mics on s5, bottom is for using phone normally, top is for when you use in speaker mode.
Might be worth a try.

navpal said:
My microphone on my S5 is not working. When I make a call I can hear the person but they can not hear me I also tried recording my voice and it didn't work, so clearly I am assuming the microphone is broken. What part do I specifically need in order to replace the microphone and have it working?
Click to expand...
Click to collapse
Is your phone rooted?
If yes than are you using custom kernel?
If Yes than which kernel?
Sometimes it is due to kernel.

Such problems are more s 5 s
This is probably due to the waterproof cover

I have a rooted stock G 900 a mic doesn't work but speaker does. left touch button doesn't work or light up. the device is still under warranty so we sent it back to Samsung and they wanted almost $200 to fix it whereas I am going to pay $10 for that whole board and microphone I'm fix it myself I am hoping that this will fix the problems. I am 99% sure it is because of some water damage. just a small amount of water I believe got in the charger port. check out what. I will update on this too with results. maybe a video. I have replaced glass and motherboards on many s5 but this is a really advanced repair

navpal said:
My microphone on my S5 is not working. When I make a call I can hear the person but they can not hear me I also tried recording my voice and it didn't work, so clearly I am assuming the microphone is broken. What part do I specifically need in order to replace the microphone and have it working?
Click to expand...
Click to collapse
Seems like my S5 is doing the same thing. It started doing this just in the last few weeks, and I haven't figured out how to address the problem.
I am having the same issue as navpal above
Does anyone have any idea how to fix this frustrating problem?

I also would appreciate if solution were posted. HEre are things I have tried with no success.
I cannot even slightly be heard on other line, except when in speakerphone mode. I can hear myself on my side, so I know that the sound is being recorded by at least one microphone.
tried:
clearing system cache
factory reset
clearing out microphone with pin

Hi there.
I have (not mine) Samsung S5 in my hands
Have tried:
Safe mode
battery out of the device and back on method
cannot do factory reset - still don`t want to disturb the client about that
Can you give me picture only of the MIC,not the whole board and others?
Maybe i can try clean it.
If i try to replace the old one will that be enough for me - i attach one photo ?
How is that done at all?
Thanks in advance

Hey Guys,
Im having the same issue. My phone went underwater without the USB flap cover and now the microphone does not work.
Should I replace all USB board? or replacing only the microphone piece would solve the problem?
Also, I wasn`t able to find more threats about it, if you guys have it, please help posting here the link.
Thx

You're about a smartass aren't you

This is an old thread, but I wanted to share my solution to this. My mic audio was very weak in speakerphone mode on Galaxy S5, but was OK in normal phone mode. The S5 has 2 microphones: bottom one is for normal mode, only top one is used in speakerphone mode. On mine the top mic hole was internally plugged with some debris. After cleaning it out by carefully inserting a broken-in-half toothpick (the blunt end) and twirling it while holding phone upside down to allow dirt to fall out, my speakerphone mic audio problem has been solved. If your mic audio is OK in speakerphone but weak in normal mode, it could be the mic hole along the bottom edge that needs cleaning. Using Voice Recorder in INTERVIEWEE mode will test only the upper microphone. Other modes of Voice Recorder enable both microphones so would be less conclusive. Cleanining out the mic holes completely solved my problem, while software fixes such as unchecking noise cancellation did not make any significant difference. Hope this is helpful.

sina_samand2002 said:
Such problems are more s 5 s
This is probably due to the waterproof cover
Click to expand...
Click to collapse
My friend you saved me.!!!! i have tried a lot of things but the cover was the problem. Without it the mic in speakermode works great now.... I think even Samsung cannot explain this.!!!