Database Users

Setup for using XDA on Irish Eircell GSM/GPRS Network

For use the Eircell GSM/GPRS enabled network, For use with Pocket PC 2002 Operated Devices, GPRS settings, Pocket |
| PC operated devices |
|-----------------------------------------------------------------------------------------------------------------------|
This document will show you how to configure your pocket pc XDA device for use with GPRS
Procedure
1.) Tap Start, and then tap Settings.
2.) Tap Connections, and then tap Connections.
3.) Under Internet Settings tap Modify then New.
4.) Enter the connection name, in this case, GPRS Connection.
5.) Connect using Select a modem - Cellular Line (GPRS).
6.) Now set up the Baud Rate to 115200
7.) Now tap Advanced? and select the Name Servers tab.
Enter the DNS addresses :
Primary DNS: 213.233.128.19
Alt DNS : 213.233.128.1
Tap OK, and then tap Next.
8.) Enter the Access Point Name isp.vodafone.ie
9.) Tap Finish.
10.) Now tap on Dialing Locations at the bottom right.
11.) Tap on Dialling Patterns and Enter a single G for each of
the 3 Options and tap Ok twice.
Your XDA is now ready to connect to GPRS.
Username & Password should both be vodafone.
You can ring to check.

Just to let you know that the settings provided by Vodafone Ireland DO work perfectly, BUT not in all areas of Dublin !!!
For days I was getting the message that there was no answer from the number dialed when trying to connect to the GPRS network but Vodafone Data Centre couldn't figure it out until I told them that it works perfectly in some parts of the city. They are now investigating a potential GPRS problem with some of their cells. I have found them to be very helpful if you need asistance.
DF
Dublin

Vodafone Ireland
Hi
what's the Vodafone phone number for connecting to GPRS in Ireland.
Kind regards
Tormey_no10

968 788743 668437 382537
Turn the number into text if it's unclear - the xda phone keypad should help :wink:

Vodafone Ireland
Has anyone managed to get Vodafone GPRS working properly around Dublin ? I have used all the settings provided by their Data Centre but can't get it to work. Any help would be much appreciated.
Thanks

I have just unlocked my XDA II (PPC2003) and inserted my 087 Vodafone SIM. GPRS is working fine but when connected to GPRS and I either make or receive a voice call the GPRS connection is dropped. when I try to re-connect it tells me that the answering modem is not responding (isp.vodafone.ie). I need to soft-boot the device or turn wireless off then on again to be able to re-connect to GPRS. Anyone had this and can anyone help solve it.
Kevin

macintosh tiger & bluetooth connection XDA for gprs

plz help
 
has anybody connected internet via bluetooth on a apple powerbook with mac osX through XDA II (GPRS). i am able to do tht on a windows platform But very new with macintosh ...
please help....
thanks

hard
that's the most difficult thing to achieve.
I dont think you can do it...

no it's not , I did it, it's just a question of finding a modem in your list and it should be a BT modem.
Pair your device from MAC OS and choose to use it as a internet dialer.
Then in your network configuration choose Blutooth then in the Bluetooth modem choose a BT modem, I think any should do the trick, I use one called au cdmaOne Bluetooth Adapter, wich I don't phisicly have but had downloaded quite some time ago (I'm talking about months ;-) when i use to have Nokia phone (surch google).
In the phone number I use *99#, mind you I live in the Netherlands so don't know if it would be the same everywhere. I have T-Mobile.
When done, open internet connect and connect.
I got it to work wright away when I first tried so it should work
Hope that helps
Greetz
Djslash

Here's how I make my Mac OSX 10.4.4, PDA2K, and AT&T mMode service play together. For other services you will likely have to adjust the APN, username, and password. For help on such setting be sure to check out: http://www.taniwha.org.uk/gprs.html
Now, on to the instructions:
On your PDA phone:
Set your phone to discoverable. (On the Today screen click on the bluetooth icon and choose Bluetooth settings. On the General tab make sure it says "Bluetooth is ON." If not, click "Turn on."
Change to the "Accessibility" tab. Make sure both "Allow other devices to connect" and "Other devices can discover me" are checked.
Change to the "Services" tab. Choose "Dial-up Networking Server" from the list and uncheck "Authorization required." Tap "ok."
On your OSX Mac:
Choose Set up Bluetooth Device
Continue
Any Device
Continue
Select your phone from the list
Continue
Continue
On your PDA phone:
Type the number into your phone when your phone prompts you to, then tap "ok"
On your OSX Mac:
Select at least "Access the Internet with your phone's data connection." Choose additional services if you desire.
Continue
Enter Username: "None" (The HTC software seems to not accept blank username/password from a Mac, so type None instead of leaving these blank)
Password: "None"
Phone Number: *99#
Modem Script: au cdmaOne Bluetooth Adapter
The other selections are optional, but keeping them checked seems convenient.
Continue
Quit
On your PDA phone:
Make sure GPRS is disconnected and you just have the white square with a G and no arrows underneath. If the arrows are there, hold the red phone button until it disconnects.
---------- Only required for some carriers (not needed for AT&T) ----------
-Now go to Start->Programs and run "Wireless Modem"
-Open Tools->Options
-Make sure "Preset GPRS Connections" is checked
-Enter "Proxy" for your Access Point Name (APN).
-Tap "ok"
-Select "Bluetooth" from the drop-down box and click "Start" to make your PDA phone listen for connections.
---------------------------------------------------------------------------
On your OSX Mac:
Click on the Internet Connect menu on your menu bar and choose "Connect"
After 10 to 15 seconds your Mac should be connected to the Internet.

Please help...
I recently bought a new iMac but have not yet got internet connection, so i got onto the web using my Xda Mini in the same way it is printed above.
It was a perfect connection and i was very pleased to actually get online, however i have no idea how much all of this will cost!
While i was online, my GPRS symbol at the top was the white box with a 'G' inside - it didn't have the moving arrows. So how was i still able to get a connection?
I understand that GPRS works by the amount of data you download - is this still the case when you're online on a computer?
I am on a straightforward pay monthly O2 scheme, by the way.
Thanks for any help!

You have to check with your service provider ask them what your per kilobyte billing rate is. There is a text file on your Mac called /var/log/ppp.log . When you disconnect from the internet your Mac writes the total number of bytes transfered in that session to this file.
The easiset way to view that file is to run:
Machintosh HD : Applications : Utilities : Terminal.app
Then type:
Code:
cat /var/log/ppp.log
The number is bytes, but most providers bill by kilobytes, so divide by 1024.

The BT connection with Dutch T-Mobile works OK; however I do have the problem that I keep losing connection after 10-30 mins of being online. Also I do have a problem that in some cases the modem of my Wizard does not seem to respond.
Is the modem just slow or somehow erratic perhaps? Does anyone have the "Modem error" as well?

guide to connecting laptop to web via universal

i have an m5000 and would like to use it as a modem to surf the web on my laptop. can anyone give me simple instructions as to how this is done. i have looked at the wireless modem app but can't see how to initiaite a connection on the laptop,
cheers

Using your device as a modem to your PC via USB
This is for GPRS connection
You must have from your network provider: the internet access point name, your user name and password.
Download and unzip the attached file in a folder on your desktop
1- Disconnect the device from your desktop
2- On the Activesync icon on your desktop, open "Connection Settings". Uncheck "Allow USB Connection".
3- On your device: Go to "Beam" (in Settings/Connections), and uncheck "Receive all Incoming beams".
4- Then in Programs, click on "Wireless Modem". With the Connection type on USB, click on "Start".
5- Now, connect your device to the desktop. The "Found New Hardware Wizard" starts on your desktop. Click "Install from a specific location", then "Don’t search. I will choose…", then click on "Modems", and "Have Disk…" and go to the folder where you unzipped the attached file.
The HTC USB Modem will be shown in the compatible hardware: click to install. Continue if you receive the alert of the software not passing the Windows XP compatibility test (Continue anyway). Finish.
6- Now, in Control Panel of your desktop, open "Phone and Modem Options". Select the "HTC USB Modem" and click on "Properties". In the "Advanced" tab type for "Extra initialization commands":
AT+CGDCONT=1,”IP”,”xxx”,””,0,0
where xxx is your internet access point.
Click OK to finish.
7- On your device (always open in the Wireless Modem program), click on Tools/Options. Check the Preset GPRS connections and write in the APN, your network provider internet access point.
8- Finally, on your desktop, go to "Network Connections" and click "Create a new connection". Choose "Connect to the internet", then "Set up my connection manually". Click "Connect using a dial-up modem", then give a name to your ISP. In phone number type *99#. Get username and password from your network provider.
Better keep a shortcut of this connection on your desktop for quick access.
Each time you want to use your device as a modem:
Disconnect your device
Disable Activesync from your desktop by unchecking the “Allow USB connection”
Open Wireless Modem on your device and push on Start (with the Connection Type on USB)
Connect your device, then dial from your desktop using the shortcut you created
PS: Remember to enable Activesync once you’ve finished.

Hi Tekflow
I have never seen on this forum such a precise and simple guide !
You thought of everything and it is working perfectly for me
Until now I had a Novatel internal UMTS modem,but using the JJ is much better
Thanks mate (actually neighbour...)
Raphael

How much of Tekflow's excellent guide applies to Bluetooth modem connections?

Well, guys and dear neighbour, regarding Bluetooth, I did not try it yet, because I work on a desktop and not a notebook, so I prefer USB connection.
Still you can try this:
(If your PC does not have an integrated Bluetooth connection, you must first install a Bluetooth dongle (USB to Bluetooth) on your PC, with the related software (widcomm or other))
Open on your PC in the Control Panel the Phone and Modem Options
Choose Modems, pick the Bluetooth Modem, then click on Properties
Click on Advanced tab
Type in Extra Initialization commands:
AT+CGDCONT=1,”IP”,”xxx”,””,0,0
where xxx is your internet access point.
Now, on the Wireless Manager of your device, turn WiFi Off, and Bluetooth On, then click on Settings/Bluetooth Settings and check "Make this device discoverable..."
On your PC:
Click on Bluetooth icon (My Bluetooth places)
Click Bluetooth Setup Wizard.
Choose I want to find a specific Bluetooth device …
After a search period, an icon of your device is displayed (usually with your owner’s name): double click for settings
From the Dial-up Networking Links, click on SSA
SSA settings: Modem: Bluetooth Modem
Number to dial: *99#
User name and password, according to Network provider
Please tell me if this works

Tekflow:
Thanks for your additional input. I'm not having any success though, although I'm convinced I'm not far from success.
I'm confused: In the help for my laptop's BT it says that "Dial-up Networking allows a remote Bluetooth device to use a modem that is physically attached to [the laptop]."
When I search for Bluetooth devices, choose my Exec and then browse the Exec services, I see the service "Dial-up Networking on HTC Universal". Is this correct? Maybe both the laptop and the Universal offer this service. I want to use the DUN on the Universal but don't need it on the laptop. Is that right? (I can disable DUN in the laptop's list of services?)
I've turned on BT on the Universal and started the Wireless Modem app, choosing Bluetooth as the Connection Type.
So, I've created a Bluetooth modem attached to COM5 with your special initialisation command (using 'mobileweb' as my internet access point). When I query the modem it responds confirming it's a Pocket PC. All looks good.
I've created a new dial-up connection, using the new Bluetooth modem and with the connection properties for O2 GPRS (number= *99#, username= mobileweb, password= password).
However, when I try to connect this new DU connection, I immediately get the error dialog on the PC- "Error 633: The modem (or other connecting device) is already in use or is not configured properly."
Any ideas?

OK, here is another step by step:
First on the UNIVERSAL open Wireless Manager: turn WiFi OFF and Bluetoth ON
then in Settings select Bluetooth Settings, and check "Make this device discoverable to other devices".
To set up Bluetooth drivers on your PC, click on the Bluetooth icon in the System Tray in the bottom right hand corner of the PC's screen. Click 'Add' to begin the search for the UNIVERSAL. Note that some PC's are installed with other types of BT software that will look slightly different.
Check the 'My device is set up and ready to be found' (discoverable) and press 'Next'.
After a short period of searching, an icon representing the device will apppear, with your owner's name used on the Universal.
Select the UNIVERSAL device and begin the Bluetooth "Pairing/Bonding" process. Select the 'Use the Passkey found in the documentation' and enter the appropriate PIN (usually "0000") and then press 'Next'.
The pairing process begins with the UNIVERSAL.
On your UNIVERSAL, enter the same Passkey/PIN entered on the PC and tap on the 'ok'. The Partnership Settings screen will appear, press Finish.
Windows™ XP Service Pack 2 automatically detects and installs the drivers.
Press Finish to complete the Pairing of the PC and Device.
Clicking on the System Tray Bluetooth icon again will now find the previously bonded UNIVERSAL. Select the device and click Properties.
Check the available services on the UNIVERSAL. Select the Dial-Up Networking (DUN) Bluetooth Profile and click OK.
From the Network Connections screen click on "Create a new connection" and click "Next".
Proceed with the following: "Connect to the internet", then "Set up my connection manually", then "connect using dial up modem"
Select the Bluetooth link, click Next, then OK on the next window
Name the Connection and click Next.
Enter the User name and Password for the Connection and click Next. Then click Finish. The dial up connection is now setup.
Now use the Control Panel > Phone and Modem Options to add in your operator's APN:
Select Bluetooth Modem and click Properties. Then select the Advanced tab at the top. You must enter your operator's APN (Access Point Name) to the internet in that location. This is a common mistake and the modem won't work without it! This information is also contained in the UNIVERSAL in the 'Start > Settings > Connections > Tasks > My ISP > Manage Connections'. The APN for the O2 UK network, for example is "mobile.o2.co.uk", so the line would be at+cgdcont=1,"IP","mobile.o2.co.uk".
[The APN selects which path the data takes within your operator's network. Alternatives to the internet APN may be APN's to WAP or MMS servers.]
Optionally, the Access Point can also be defined in the WModem > Tools menu.
On the UNIVERSAL, run the Wireless Modem application by pressing Start > Programs >Wireless Modem. Select Connection Type: Bluetooth. Then tap Start.
From Network Connections, dial the recently created connection (i.e. "My dial-up to the Internet via UNIVERSAL Bluetooth Modem" if that was the name assigned to it).
UNIVERSAL Dial-up Connection Progress: "Dialing *99#" then "Verifying username and password" then "Registering your computer on the network"
Finally, the popup shows that the modem is now connected
When finished browsing or e-mailing, first right click the connections icon on the right hand side of the PC and press disconnect. Then deactivate the USB Modem by pressing Stop at the WModem application.
Tell me if this works, because I still don't have a bluetooth connection on my PC

thanks for a great set of instructions, very easy to follow. However it does not quite seem to work for me. I can add the exec as a modem and when I try to connect I can see that a gprs/ 3g connection is made on the exec. On my laptop it goes through the authenticating user prompt, but when it gets to registering the computer on the network it just times out and the exec drops the connection, any ideas?
I am using
Username: o2web have tried mobileweb as well
Password: password
advanced command: AT+CGDCONT=1,"IP","mobile.o2.co.uk","",0,0
wireless modem apn: mobile.o2.co.uk

Hiya megman,
In anticipation of doing tech support at my folks' house tomorrow (dial-up *shudder) I decided to set my trusty Exec up as a modem. Booze almost certainly smoothed the process out
Some notes: (a) I'm a tad drunk . (b) On the Exec, I had to make a new modem connection. I use "work" for both connection types so added my new connection there. (c) I first paired my Exec with my lappie, choosing serial port and then set up an incoming com port on 4.
Having done this, and topped up my glass, I did:
1) Connect from lappie to Exec on BT, choose dial-up networking, use the string from Tekflow (respect going out):
AT+CGDCONT=1,"IP","mobile.o2.co.uk","",0,0
in the advanced bit. Set the phone number to *99#; username:mobileweb; passwordassword.
2) On Exec, make a new connection (I didn't have one to start with) Manage Existing Connections > New... -> line:cellular gprs; APN:mobile.o2.co.uk; username:mobileweb; passwordassword; no advanced stuff.
3) Connect that puppy
4) Start Wireless Modem, making sure it's a bluetooth connection
5) On lappie, connect to the Exec via Bluetooth Settings window.
6) Job's a good 'un. Use new connection to do this!
HTH

Thanks this_mike. I forgot to put on my post that I was trying a USB connection though. I don't have bluetooth on either of my laptops.

Two things...
First, a massive thanks to Tekflow for your great setup instructions... i had been trying to do this for ages without any success
Second, for those Vodafone 3G users, the setup instructions are exactly the same, except the username and password (in the UK at least) are:
Username: web
Password: web
THANKS, THANKS, THANKS!!!

Dear,
Million Thanks to Tekflow and all the folks engaging in sheding lights on all this. I had been wrestling the use of that since my old XDA I -> XDA II. And now i just succeeded using the wireless modem with my XDA Universal.
Thank you
Ken

Re: Using your device as a modem to your PC via USB
Tekflow said:
This is for GPRS connection
You must have from your network provider: the internet access point name, your user name and password.
Download and unzip the attached file in a folder on your desktop
1- Disconnect the device from your desktop
2- On the Activesync icon on your desktop, open "Connection Settings". Uncheck "Allow USB Connection".
3- On your device: Go to "Beam" (in Settings/Connections), and uncheck "Receive all Incoming beams".
4- Then in Programs, click on "Wireless Modem". With the Connection type on USB, click on "Start".
5- Now, connect your device to the desktop. The "Found New Hardware Wizard" starts on your desktop. Click "Install from a specific location", then "Don’t search. I will choose…", then click on "Modems", and "Have Disk…" and go to the folder where you unzipped the attached file.
The HTC USB Modem will be shown in the compatible hardware: click to install. Continue if you receive the alert of the software not passing the Windows XP compatibility test (Continue anyway). Finish.
6- Now, in Control Panel of your desktop, open "Phone and Modem Options". Select the "HTC USB Modem" and click on "Properties". In the "Advanced" tab type for "Extra initialization commands":
AT+CGDCONT=1,”IP”,”xxx”,””,0,0
where xxx is your internet access point.
Click OK to finish.
7- On your device (always open in the Wireless Modem program), click on Tools/Options. Check the Preset GPRS connections and write in the APN, your network provider internet access point.
8- Finally, on your desktop, go to "Network Connections" and click "Create a new connection". Choose "Connect to the internet", then "Set up my connection manually". Click "Connect using a dial-up modem", then give a name to your ISP. In phone number type *99#. Get username and password from your network provider.
Better keep a shortcut of this connection on your desktop for quick access.
Each time you want to use your device as a modem:
Disconnect your device
Disable Activesync from your desktop by unchecking the “Allow USB connection”
Open Wireless Modem on your device and push on Start (with the Connection Type on USB)
Connect your device, then dial from your desktop using the shortcut you created
PS: Remember to enable Activesync once you’ve finished.
Click to expand...
Click to collapse
Excellent guide. Thanks Tekflow!

I'd had problems with this up until now, just followed the guide and got it working first time... Thisll save me trying to find a wifi connection when on business

usb modem error!
Hi everybody!
I tried to connect laptop to my Universal but in wireless modem with USB type when I tap START I receive an error: " COM OPEN ERROR"
Any idea???
thanks

cata delete any bluetooth outgoing port setup you have for xample I had a bluetooth outgoing gps reiciver setup and delted that fixed the com port issue,
got the info from another thread so if it works all credit due to that chap

Nice work Tekflow
I added a link to this topic in the wiki under Universal/FAQ

How can I figure the username/password for T-Mobile USA?

t mobile mda pro user pass ?? anyone?

Thanks to Tekflow et al. I have now managed to connect using both methods [USB/Bluetooth], I prefer BT over USB though so I don't have to keep on fiddling with Activesync Connection Settings. BTW am posting this now using my Exec as the modem.

Using GPRS as a Modem to surf internet with Desktop/Notebook

There are three main steps:
1. Pairing the devices
2. Configuring the modem using an AT string
3. Creating a new internet connection using the modem
Let's start with the first step: pairing the devices and using the modem on the PDA.(Photo 1-3)
Now, run a connection wizard on the Desktop/Notebook (New Connection). I am going to show you the procedure in detail, so I opted for the Custom Mode.(Photo 4-6) The device is then checked for supported services. In our case, the Wizard offers only one but very important service, Dial-up Networking.(Photo 7)When you click Next, the devices will try to pair.
If everything goes well, the PC should display a window asking for a PIN. It does not matter what you type in (can be 8888) [Photo 8], you only need to remember this because you will have to enter the same code in the PDA. This protects you against intruders. On the pocket device, first confirm that you realy want to communicate with the PC (Yes) and then enter the PIN (Photo 9-10) .Check the box at Serial Port and tap on Finish.(Photo 11)
We are done with the PDA for the time being but need to do some more setting on the desktop/notebook. A Bluetooth driver from Notebook offers a quick configuration of the newly connected modem (Photo 12). Click on Advanced Modem Settings and enter the following string in the only possible field: AT+CGDCONT=1,"IP","APN", where the "APN" should be replaced with APN details of your provider (Photo 13).
For Example. APN for 'Peoples' is Peoples.net
Please note that different notebook may have different bluetooth module so that the above photo display may not be same.
The last step involves filling in a form where you enter a name for the connection being created in the first field and specify a dial-up string in the second field and leave the rest blank. In this case, we typed in Dial-up Connection Name : Vodafone GPRS or keep the current default connection unchanged. Telephone number is *99# which is universal setting for GPRS.(Photo 14)
That's it. Now at Notebook/Desktop select Start -> Settings -> Network connections -> Your new connection and then Dial and you should be connected to the internet .
The procedure should be similar with other BT modules.
Please note that all photo is not mine but I tested on my 818pro and Notebook and work fine.
Using GPRS as a Modem to surf internet with Desktop/ Notebook with USB Cable:

sas, I have tried your procedure and for some reason can't get it to work... do you know if the Prophet will work as a GPRS modem through USB cable? I have the newest ROM for the JAMin... maybe this is why I can't get it to work??

Using WModem for wireless modem on Vario II

I'm trying to get my Vario II to act as a modem to my laptop using the phone's 3G connection.
I eventually located the "generic modem" driver files to permit the phone to act as a modem to my laptop but I don't know what to do next. I've installed the driver and Windows (XP) reports that the generic modem is installed and working OK.
The downloaded files also included a program called "HTC USB Modem" and when I run this I am asked for a Username and password - and I haven't a clue what I should enter since I don't normally have to enter anything on my phone to access 3G.
Can anyone tell me how to proceed? Or tell me another way to get my phone to act as a modem to my laptop?
Cheers.
Bobby

i have the same problem, have you solve the problem ?
francesco

3G access thru PDA
u could try this...
Number: *99#
Username: your 3G access username (some telcos do not use it so leave it blank)
Password: Your 3G access password (some telcos do not use it so leave it blank)
remember to set your access point on your wireless modem before connecting.
cheers.

leo-chan said:
u could try this...
remember to set your access point on your wireless modem before connecting.
cheers.
Click to expand...
Click to collapse
That last bit threw me Leo. What exactly to you mean by this?

Your network requires you to connect to an access point. If your device came from the network it was already set up to do so. As you need to manually enter the access point (or APN) and any user/password details, you need to google for your networks GPRS Settings.
For example with Orange, their APN = orangeinternet
(with no username or password.)

@bobbyelliot
I notice you are using T-mobile Uk
Their GPRS settings are:
Mode ...................................Permanent
Security ...............................Off
Bearer .................................GPRS
Connection ..........................When Needed
IP Address ..........................149.254.001.010
Port Number ........................9201
Authentication ....................Normal
Access Point Name ..............general.t-mobile.uk
Login ..................................Automatic
User name ..........................user
Password ...........................wap
Web site http://wap.t-mobile.co.uk / or http://www.t-zones.co.uk

Thanks for these details Mike but I still can't configure my Vario II to work as wireless modem to my laptop.
When I create a new Dial-Up Networking connection (I have to do that, right?), it doesn't ask for any of this information (except the ID and password) but does ask for a telephone number - which I haven't a clue about.
Can someone give me an idiot's guide to getting the Vario to work as a (3G) modem to my laptop?
Cheers.
Bobby

type *99# for tel no
user for user name
pass for password
this is what i put for t-mobile uk

Thanks. Tried this. Would only begin to work with GPRS (not 3G). But still failed with GPRS, reporting "Please end data call first." (on my PPC). I messed about with various permutations of start/stop wireless modem etc. but I didn't manage to get a connection. Help!
Bobby

wiki
bobbyelliott said:
Thanks for these details Mike but I still can't configure my Vario II to work as wireless modem to my laptop.
When I create a new Dial-Up Networking connection (I have to do that, right?), it doesn't ask for any of this information (except the ID and password) but does ask for a telephone number - which I haven't a clue about.
Can someone give me an idiot's guide to getting the Vario to work as a (3G) modem to my laptop?
Cheers.
Bobby
Click to expand...
Click to collapse
I am no techie but I did it by following the info on the wiki site and I have the same phone and same network. Mine works ok - have you had a try this way?

active sync
bobbyelliott said:
Thanks. Tried this. Would only begin to work with GPRS (not 3G). But still failed with GPRS, reporting "Please end data call first." (on my PPC). I messed about with various permutations of start/stop wireless modem etc. but I didn't manage to get a connection. Help!
Bobby
Click to expand...
Click to collapse
Before you dial you need to untick the usb connection in the active sync. Otherwise it thinks you want to do that instead. Have you tried that?

bobbyelliott said:
Thanks. Tried this. Would only begin to work with GPRS (not 3G). But still failed with GPRS, reporting "Please end data call first." (on my PPC). I messed about with various permutations of start/stop wireless modem etc. but I didn't manage to get a connection. Help!
Bobby
Click to expand...
Click to collapse
Open the comm manager and disable the data option (a little PDA with two arrows) then open the modem and select start. Now when it is plugged into the USB cable the PC will not recognise it as a PDA but as a modem.
Then configure a dial up connection with the options described above and it should connect OK. If not call 150 and they will talk you through it in a couple of minutes.

bobbyelliott said:
I'm trying to get my Vario II to act as a modem to my laptop using the phone's 3G connection.
I eventually located the "generic modem" driver files to permit the phone to act as a modem to my laptop but I don't know what to do next. I've installed the driver and Windows (XP) reports that the generic modem is installed and working OK.
The downloaded files also included a program called "HTC USB Modem" and when I run this I am asked for a Username and password - and I haven't a clue what I should enter since I don't normally have to enter anything on my phone to access 3G.
Can anyone tell me how to proceed? Or tell me another way to get my phone to act as a modem to my laptop?
Cheers.
Bobby
Click to expand...
Click to collapse
Bobby,
Let's try and get this working for you. I assume that you are on a T-mobile Web & Walk package and want to use the Vario II as a modem for the laptop to allow a data connection via your T-mobile 3G and GPRS access? If this is so then here goes:
- Configuring WModem on Vario II - Go to Programs and select the WModem option. select Menu - APN Settings. Ensure 'Preset GPRS connections' is ticked and in the APN box enter 'general.t-mobile.uk' then click Done.
- Modem configuring - you seem already to have done this as you have installed the drivers and say it is working - that means you also know how to start the "wireless modem" function on the Vario II in programs.
- Forget about the HTC USB Modem software - just create a new Windows XP 'connection'. I found that this software just added a level of complexity and it meant that you had to enter settings (usernames and password) manually each time.
- Create a Windows Connection on the laptop/PC:
- go to 'show all connections' then click 'create a new connection' (or follow the new connection wizard if this view is what you use).
- Select 'Connect to the Internet', then 'Set up my connection manually' then 'connect using a dial-up modem' then in the ISP Name box that comes next enter something of use like 'Vario II (T-Mob) Connection'
- In phone number enter *99#
- In username enter 'general.t-mobile.uk'
- In the password fields enter 'one2one'
- Consider unticking the bottom 2 options for default and allow all users...
- Save all the settings so far and close the wizard and dismiss the dial-up that appears.
- Change Dial-up Settings - You have created a Vario II dial-up for use by the laptop but you need to ensure that the dial-up uses the Vario II 'HTC USB Modem' and not the built-in laptop/PC modem:- Start WModem - with the Vario docked or USB connected (and activesync running OK) start the WModem (from programs) by selecting Menu - Start. This should stop activesync automatically and then your laptop/PC should see the HTC USB Modem (the Vario II with the WModem running).​- On the laptop/PC go into your available connections and right-mouse select properties on the new Vario II connection. In the first (general) tab under 'Connect Using' select/tick the entry for the Vario II modem that should read 'Modem - HTC USB Modem (COM#)' - where COM# is the com port automatically set by the laptop/PC. Check the phone number. Make sure that any other modem is unticked.​That should be about it and all should now work! To use the connection just set-up turn off your wireless network or unplug the network cable, then connect the Vario II with the USB lead, then start WModem (the program and menu-start!) on the Vario II, then on the laptop just double-click the connection that you created. Note that the laptop/PC will display the data connection established to the Vario II not your 3G/GPRS connection speed. I changed the settings on my Vario II USB Modem to increase the maximum speed of the connection (to the modem only) to 921600bps and also checked the Hardware features were all ticked.
Hope this helps - let me know if you have a problema and I'd be glad to help more. The connection works seemlessly on my laptop and basic surfing and e-mail is really quite fast - way quicker than a 56k dial-up that we all used to have!
Regards

Tony, you beat me to it!
Good description on how to setup wmodem.
Imp

hi, this is NOT my guide just posted it here cos i cannot remeber the exact link ( it is from universal forum); i did everything according to this steps and all is good been using my hermes as modem since i got it yesterday hehe
so here is the guide and u need to have the driver mentioned in this thread.
have fun it works for me so it should work for u.
access point for t-mob uk : general.t-mobile.uk
user: user
pass: wap
-------------------------------------------------------------------------
You must have from your network provider: the internet access point name, your user name and password.
Download and unzip the attached file in a folder on your desktop
1- Disconnect the device from your desktop
2- On the ActiveSync icon on your desktop, open "Connection Settings". Uncheck "Allow USB Connection".
3- On your device: Go to "Beam" (in Settings/Connections), and uncheck "Receive all Incoming beams".
4- Then in Programs, click on "Wireless Modem". With the Connection type on USB, click on "Start".
5- Now, connect your device to the desktop. The "Found New Hardware Wizard" starts on your desktop. Click "Install from a specific location", then "Don’t search. I will choose…", then click on "Modems", and "Have Disk…" and go to the folder where you unzipped the attached file.
The HTC USB Modem will be shown in the compatible hardware: click to install. Continue if you receive the alert of the software not passing the Windows XP compatibility test (Continue anyway). Finish.
6- Now, in Control Panel of your desktop, open "Phone and Modem Options". Select the "HTC USB Modem" and click on "Properties". In the "Advanced" tab type for "Extra initialization commands":
AT+CGDCONT=1,”IP”,”xxx”,””,0,0
where xxx is your internet access point.
Click Ok to finish.
7- On your device (always open in the Wireless Modem program), click on Tools/Options. Check the Preset GPRS connections and write in the APN, your network provider internet access point.
8- Finally, on your desktop, go to "Network Connections" and click "Create a new connection". Choose "Connect to the internet", then "Set up my connection manually". Click "Connect using a dial-up modem", then give a name to your ISP. In phone number type *99#. Get username and password from your network provider.
Better keep a shortcut of this connection on your desktop for quick access.
Each time you want to use your device as a modem:
Disconnect your device
Disable ActiveSync from your desktop by unchecking the “Allow USB connection”
Open Wireless Modem on your device and push on Start (with the Connection Type on USB)
Connect your device, then dial from your desktop using the shortcut you created
PS: Remember to enable ActiveSync once you’ve finished.

managed to find the USB driver/file so i attached

sorry was too lazy to reply as I really can't remember the whole wireless modem ****...
moved on to wm6 now, internet sharing is a breeze.

T-Mobile Charges for Vario use as modem
Hi,
I set up the Vario II as described above and it worked fine. What I don't understand is why T-Mobile should charge more (£7 per month extra, or thereabouts) simply because a laptop is included in the system. Surely, provided you don't go over your limit for W&W (1 Gig) then why should they worry?
Am I likely to be charged extra, simply for accessing what I can already access from my Vario ii, but using a laptop as the "front-end"?
Cheers,
Ken

harrogate22 said:
Hi,
I set up the Vario II as described above and it worked fine. What I don't understand is why T-Mobile should charge more (£7 per month extra, or thereabouts) simply because a laptop is included in the system. Surely, provided you don't go over your limit for W&W (1 Gig) then why should they worry?
Am I likely to be charged extra, simply for accessing what I can already access from my Vario ii, but using a laptop as the "front-end"?
Cheers,
Ken
Click to expand...
Click to collapse
u need to exceed the limit of 2gb i guess to be warn but then you can still you ur w&w. i been using my vario a lot never had any problems with t-mob

if your using a updated rom you dont have the option of a WModem do you?