Hello Guys!
i desperatelly need an advice...
Few weeks ago i bought ocasionally almost brand new SPV m500 and that is how my problems starts...
First of all i needed to took off SIM lock[orange to o2]...actually it was big battle that i lost...You want to know results ? Mobile doesnt read any sim at all...
What about connection problem :
1. installing active sync 4.1( before i install AC i tryed to connect device and wait for effects [winXP should automatically detect new hardware] unhapilly win xp poping up small clound in down right corner and inform me : ''USB DEVICE NOT RECOGNIZED''
2.after instalation aplication asked me to connect mobile device(i using standart USB cable) so i did it
3. and what?? information in AC : ''your device was not connected'' and above : '' verify that connection you re using is avalaible'' and above list of detected ports : COM 1 , COM 2 , IR, USB is activated
4. i trying to press 'next' but it goes around i mean it shows again
I checked all avalaible ver of active sync on difrent PC (even win98) and nothing, same thing..
The strangest thing is everything was all right with connection before i tryed handle that sim lock....
now i dont know what to do my ideas to solve that problems just finished...
I search your forum.xda-developers.com and there is a lot of PRO here...
will be great if someone can help me....
big thanks upfront
I've same problem
I've same problem
Hello,
With which software and How did you remove the SIM lock?
Regards
Carty..
unlocked spv m500
i tried to unlock my spv with some software that reset the radio to version 0.00 which just erased my radio firmware!!!! i then tried the xda-dev unlocking software which worked and then flashed the spv with the i-mate firmware and then customised it with the orsnge software,this has no problems that i know of
Carty said:
Hello,
With which software and How did you remove the SIM lock?
Regards
Carty..
Click to expand...
Click to collapse
Hello Carty,
Sorry for no reply long time,
I tryed to unlock using all versions of xdadev_all_unlock.exe
What about conseqences?
I cant access my spv at all ...
now when i put any[even orange] sim into the phone always asking for unlock code [ when i type 0000 or sth like that i've got ''you have tryed 24 times...'']
please if you know how to solve even one of these problems help me!!
Related
hi to everyone,
i have a locked-SIM t-mobile phone edition which i tried to unlock using a serial cable & the manipulator.
the problem is that the manipulator can't find the device after scaning COM port.
i have checked that the port is not blocked by any program including the synchronization programs but there was no luck.
anybody knows what is the problem in my situation?
Be sure to press SIMULTANEOUSLY both power button AND reset with your stylus. This will bring your T-Mobile to WALLABY mode. After the screen reads GSM OK, connect the cable to your phone and PC and run manipulator.
This should work. I have the same T-Mobile and it worked with mine.
There have been posts with reports where people have had problems connecting to the pda because they have been using a laptop...
I unlocked mine on a SONY VAIO laptop successfully.
hi again,
i have tried the exact steps for unlocking but still the device wans't detected by the manipulator.
the synchronization program also can't detect the device if it is pluged using the serial cable.
could anyone please help me? i couldn't use the phone since 1 month.
Try 75656354
Wasn't there in any thread the hint to uninstall ActiveSync to get the manipulator to work?!?!
Search here in the forum. It wasn't posted as long time ago.
Or just try it when you uninstall.
I ment that there was a problem because active sync wants to connect to the XDA/MDA when connecting it to the serial....
Regards
LumpiStefan
Remember you must have the XDA in bootloader mode.
Hi guys, at the mo i have my phone in boot loader with the 4 colours and usb on the bottom left..
i am looking for the rom file.....currently i have tried using : -
Qtek_9100_RUU_Prodigy_10107105_Qtek_WWE_ship.exe from ftp://xda-developers.com/Uploads/HTC_Wizard/Roms/Qtek/ but when i load it says
'The application has failed to start because RAPI.dll was not found. Re-installing the application may fix this problem'
have also tried the T-mobile one and it says the same thing as above
so what do i do now?????????? someone please give me a direct link to the correct file as i cnt find it ne where
thanks
?? anyone please...
According to the Northern Hill Software web site, these kind of RAPI.dll errors can occur because you don't have ActiveSync installed on your PC (or your installation is corrupt).
Man, serious déja vu... I'm POSITIVE I've had this same discussion with someone else in the past on these forums before. :S
Hi,
I also experienced this problem. But after disconnecting the usb connection and after soft resetting the mda the old installed version worked again.
For me the problem was that i didn't unlocked the CID. I first had to unlock the CID (with the MDA vario) to be able to update an other rom.
Hello,
I have an unblocked SPV M560 (HTC3300).
Few weeks ago I have installed the B&B rom with WM6 on it. Now I would like to install the adinfinitum rom (http://www.adinfinitum.fr/wm6_gps_m6...d_and_the_ugly) to solve the GPS problem we can have with the M650 but I cannot flash anymore.
Here are some explanations:
After starting "start_uspl.exe" I get the Linux screen then the RUU application starts on my PC. RUU is trying to connect to the device but after few seconds it displays the error "ERROR[260]: Update error".
After this I tried to restart the pda, wait for Activesync connection and try to restart RUU.
This time RUU can connect, I can see the grey screen on the PDA and it starts updating... but after 2% I get a black screen on the PDA and RUU displays the error "ERROR[270] Update error".
I'm now reading this forum since 2 days and saw that other people already had this problem but I did not find any working solution.
Does anyone of you have an idea of what can I do to solve this problem?s
Thanks in advance for your help.
Alain.
REad this...
Remove sim and mem card from phone use clear storage to clean phone memory then again try start_uspl.exe wait to 100% finsh do not disconect phone and run then romupdateutility i hope that this can help mine problem is resolved and i flash spv m650 many times.
Hi, i have similary problem, when i try re-install WM on my xda orbit 3.15.118 i have alert : flashing error check your update utility..when i try install another WM6 i have alert : error 270:update error
battery full charged
anyone help me ;-)
Hi,
I finally managed to do the update. The only difference is that when RUU has started after getting the black screen I clicked on the cancel button.
After this I let the terminal with this black screen for few minutes (about 5 minutes) and starts again the RUU application.
And this time is works... don't ask my why, maybe it takes some time to the terminal to be ready to accept connections. At least now SPL 1.1 is installed and I can upgrade. My GPS is now working
Thanks
Alain
Spv m650 arte100
when i run the start_uspl.exe i have this window after the run
No Device Connected
Would You like to try copy again?
YES NO CANCEL
boy my SPV is in bootloader mode and i can't riun it in different mode
i have IPL 3.15.0001 and SPL 3.15.0000
What i have to do ???
PLEASE HELP ME
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Have you tried updating to the latest version of Active Sync on XP
or following the guide for Vista
Take off battery. wait for about 10 hrs. put back battery and switch on the power.
Thanks for the tip's
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Furkinl said:
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Click to expand...
Click to collapse
erm u are trying to flash on a pc running vista?? thats your problem, u cannot flash on a vista pc, xp home/pro ONLY!
Thanks for the advice, tried on XP and it worked fine, it would seem that activsync was not required in this case. At least my XDA is ALIVE for now.
many thanks
You simply could revive it again by Resetting it via the stylus
thnx 4 all the soloutionsss
i had same problem , but once i tried it on xp, its works for me, my ppc now is refresh installed,
thnxx
qtek 2020i
for information the french rom is available on this place http://www.planete-htc.com/index.php?mod=download choose dangaard section there is two files to download
1. choose 2020i dangaard rom
you can not use it
2 download the radio file
it contains an exe called upgradeut make it in the directory of your dangaard folder and you will be able to flash it
it work also for pda stuck in serial usb
voila
qtek 2020i
radio file 1.04 two mega
do a hardware resett and it should be the phone back to defaults
XDA IIi V 1.01 Serial /USB
Hello,
I tried to update my XDA IIi from a new rom version found at o2.ie website but my XDA IIi is stuck and showing Serial on top and v 1.01 at botom. When i attach it with cardle it shows USB instead of serial.
I have tried Almost everything that i found on this forum in last three days.
Hard reset / soft reset/ new installation using different version etc.. but nothing worked for me..
Now I am really confused and can't find what to do.. Can any one from XDA gurus/ developer help me and sumarize what should i do?
Thanks in Advance
Zeeshan
Yes, i have the same problem i did exactly what was done above me pls can someone help!!!!!!!!!
Furkinl said:
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Click to expand...
Click to collapse
Where can I download this rom?
Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed
Thanks in advance
Chet
look and lern
put qtek 2020i in stativ (conect to pc via usb)and push power ( on screen will apear USB and v1.01), and you dezarhive :astel_wwe_11100_112_10200_ship, and doble klik on AlUpgradeUt and bios at ppc wil be update !!!!! This is all, the ppc will be now reinstaling, be patient and wait until will be reinstaled (25 min)
i have the rom updater SP3_WWE_2.4.33.11, and i go in all the processes, i am connected with activesync and when it goes to tri-color menu the phone looses activesync connections and it says that cannot have connection and freezes. what can i do? please help.
I've the same problem i sitll can solve it n anybody please help am new here i've no idea what to do. I tried unlocked CID but i couldn't do it put cert.cab in phone n wen i try to install it says can not install or SDA_applicationunlock n I also tried lokiwiz procedure but still can not solve it so please if someone could help me in updating or upgrade my Orange Spv C500 ROM so it would be so nice of .... Waiting for kind reply !