i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????
Try putting your device into bootloader mode and making sure your XDA is plugged into the mains as well. There's also an upgrade program which bypasses country id checks.
Good luck.
I got the same problem with my Qtek 2020i today!!!!!
The device is dead and i can't put it into bootloader mode!
I need your help please
Try taking the battery out for about 1 hour. This will run the backup battery down therefore wiping the ram. Put the battery back in, connect it to the mains and put it into bootloader by pressing power, action and reset for about 3-5 seconds until serial appears on screen. No backlight so look carefully.
I tried to remove the battrey for 1 hour but it's still the same!
any way thanks for trying to help pug.
Related
Need help!
I have been messing with this phone for afew days now can't seem to get it to work. When I power the phone on all I see on the screen is green screen that says "IU BUILD! Test Only" this ws the result of a hard reset. The device is sim unlocked but I don't believe it's super cid unlocked. I'm unable to do anything except for hard resets and bootloader screen. I was going to try to reflash the original rom but can't seem to find any, I only have access to the sp3 roms which I can't use since it's not super cid unlocked. Any help would be great!!!
iMate OEM ROM
http://rapidshare.com/files/61129896/SP3_WWE_2.4.33.11.zip
Here is a link to an iMate OEM ROM. Start in bootloader and execute this to see if you can recover your device. You haven't shared much about what you phone is or how it ended up like it is. You are correct that it needs an OEM ROM, then application unlocked then Super CID unlocker before flashing a custom ROM. Good Luck and report back you results.
The phone is a Krome IQ700. In bootloader mode it shows IPL 0.27 SPL 1.01.0109 Typhoon UI. Another problem is active sync does NOT see the phone. When attempting to load any rom I get error 264. I think I might have to load rom with SD the only proble is I've never had to do this before so any help would be great. I could honestly live w/o the phone but I think this would be a great learning expirence. Thanks in advance.
after attempting your reply my phone is now dead and will not power on ...
nwdrifter said:
after attempting your reply my phone is now dead and will not power on ...
Click to expand...
Click to collapse
Remove the battery and memory card, wait 30 minutes then re-insert the battery. Hold in the camera button and then plug in the USB. If it is still alive, it will open in bootloader (Red, Green, Blue) mode.
still dead... what do you think happened?
nwdrifter said:
still dead... what do you think happened?
Click to expand...
Click to collapse
I had this once when my oem battery died. I was able to jumpstart it and get it to recharge using a 9v battery to kick it up from nearly 0V.
If you have a battery meter, you can test the contacts, looking for 4v across the battery terminals (remove battery from phon to test). If you get < 2v then you battery does not have enouge juice to power up.
Once you get power back, do you have the ROM from your OEM? You should be searching for it in the mean time. If I find anything on it, I will let you know as well.
Everything I see on your phone specs appears that it should respond and behave like all of the other Typhoons/Sp3's. As long as you followed the unlocking steps from Karhoe's post (second sticky on typhoon main page), your device should not be a brick. If you recover power, you may want to first flash an WM5 ROM from one of the posts then try to flash WM6 as this is the prescribed method starting from WM2003.
All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???
Hi All,
I had this device for few months now after selling off my Eten X500.
The Universal was a big device but I truly loved the XGA big screen. And yesterday disaster struck. Normally sometimes the device would go haywire but a few soft resets or hardreset would set it back on course. But yesterday it refused to move on from the bootloader mode and when I used Buzz utility prgram, it did move away from the bootloader but didn't swith on anyway. And yes, I have flashed the ROM's quite a few times and I managed to flash it with T-Mobile's latest WM5 ROM today morning. The flash was successful but it just wont work normally.
I have 2 batteries but bith yieled the same result. I could only get it to switch on if I hardreset it on a table with 2 fingers firmly pusing the soft keys down. It would sometimes would boot but would hand after it fully loaded. I have removed the SD card as well as the SIM card. Not sure if the devie motherboard is having any issues or some connection problem. One thing for sure if I hold both edges of the device and press it hard and try a soft reset, it would boot sometimes. I even have the external battery charger and I can charger the batteries full.
Any idea how much would it cost (I'm in Singapore) for a repair or anyone who could help me with this.
The worst thing is, this is my only phone and I really need it to work asap.
Hope someone could shed some light on this.
Thank you all in advance.
Techx
Have a look at the wiki...
I had the same problem after I put it on charge with no battery in - very smart I know . It explains about using MTTY and how you format the DOC which should solve your problem - hopefully...
Hi all,
I tried the MTTY utility but I can format the DOC files. everytime I try to format it, I get an error like this :-
USB>set 14 0
HTCSF kEØ(HTCEUSB>task 28 55aa
Wait..
flFormatPhysicalDrive:status=20
Read data error in tag
DOC_format failed!
USB>
So anyone can help in this issue plssssssssssssssss
Thank you all.
Techx
anyone????
Anyone? pls help!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Do h3lp!!!!!!!!!!!!!!!!!!!!!!!
Anyway of getting the unit fixed? Anyone from Singapore can recommend a shop or anything?
--------------------------------------------------------------------------------
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
dineshkumaar said:
--------------------------------------------------------------------------------
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
Try to reflash with another ROM
And maybe your battery is not working
Good luck and don´t forget to vote!
Im new to this forum and spending a few weeks doing searches I have found a new world of things I can do with my M5000! Only problem is I have the same problem as this guy. The problem started with no GSM, No Protocol version and no IMEI number, After countless rom installs and failed all I thought I left the sim in? Took batt out, No sim, Put the batt back in and now it wont turn on or do anything.
Has anyone found a solution to this problem or its it an expensive paper weight?? Im lost without it!
ronnie5 said:
Im new to this forum and spending a few weeks doing searches I have found a new world of things I can do with my M5000! Only problem is I have the same problem as this guy. The problem started with no GSM, No Protocol version and no IMEI number, After countless rom installs and failed all I thought I left the sim in? Took batt out, No sim, Put the batt back in and now it wont turn on or do anything.
Has anyone found a solution to this problem or its it an expensive paper weight?? Im lost without it!
Click to expand...
Click to collapse
Welcome to the forum
You have a great device!
Have a look here:
http://forum.xda-developers.com/showthread.php?p=3999833#post3999833
Hope it helps and good luck,
Hello mates,
My i-mate Jasjar doesn't start any longer. Here's how I got here. I tried to flash my jasjar with Crossbow ROM using ROMUpgradeUt.exe but it didn't do anything. So I went into the Country_ID_Error folder on the computer and executed MaUpgradeUt_noID.exe. My jasjar froze after this and everytime I restarted it just hung on the bootscreen that says i-mate.
So I tried using mamaich method using mtty and now I can't even get to the i-mate bootscreen. So nothing just happens when I try to power up the phone (I'm sure the battery isn't dead).
All I can do is just enter the bootloader mode. That is the only thing that I can do that I know.
Please suggest something. I'm lifeless without the i-mate.
Thanks and regards,
Aditya More.
i had this same issue, i task28?'d my device, whatever command that resets the flash structure, then booted into bootloader, and flashed this file:
http://rs507.rapidshare.com/files/184081773/JASJAR_WWE_11353_137_10301.zip
that should fix you up real good, hopefully.
Well thanks a lot. But it doesn't help. It gives me a connection error when everything is fine. USB is connected, ActiveSync USB connection is disallowed.
I forgot to mention, that when I task 28'd my device, nothing showed on the device. It just showed USB at the top and v2.01 at the bottom for ever, which means the task 28 wasn't probably successful or I ain't sure what.
Yeah, I had to ask you how if the above given file will work if the phone is in bootloader mode.
To fill you on more details, my phone somehow strangely starts. I'll explain how.
When the phone is switched off, and when I press the reset button, nothing actually happens, no activities can be observed.
When the phone is switched off and I connect it to the computer via USB, it shows the charging light. Now when I press the reset button with the phone connected to the USB, the charging light goes off and the USB detection sound sounds on the computer and the computer shows "USB Device not recognized". This means the phone started.
But strangely in both the above cases, none of the two lights on the phone indicate anything and display of the phone shows absolutely nothing.
The only thing I can do with the phone now is enter bootloader.
Also, since I compromised so much, is it possible that I can still flash it with WM6? Because going back to WM5 will make me feel miserable.
Thanks.
@cheapusenet:
I tried flashing with that file. It flashed successfully, but the screen is all smudged. I soft reseted the phone too (using reset+two soft keys) but it keeps displaying that same smudged screen.
Good news is it did something.
Bad new is that it didn't make the mate work.
Please help. I'm dying without the phone.
Thanks and best regards,
Aditya More.
is it possible you can get a picture of what screen its showing? I THINK it happened on mine as well, did you let it sit for 10 or so minutes? if i recall the bootscreen was all corrupted but it started into WM5 just fine.
and regarding wm6, i'd attempt to get the device working before you try and get fancy. is the device cid unlocked? mine was and thats what was causing the issues.
Originally Posted by mamaich
if you can enter bootloader - use "task 28 55aa", this would restore DOC to its original layout.
If you cannot - contact service center.
if you didnt run that exact command, it's probably a good idea.
and you could try reflashing that stock imate rom?
This is all that happens.. I have waited for 5 minutes. I'll wait for 20 minutes now.
i waited for 30 minutes.. no go..
yap it did that EXACT same thing to mine.
reflash it, i think that fixed mine.
if that doesnt work, attempt flashing some custom roms.
is it CID unlocked?
i flashed it twice.. no go..
what's CID unlocked?
CID
Read the Wiki on my sig link
cid unlock allows flashing of roms that don't match your device branding.
i don't remember what brought me back from that, i may have flashed a custom rom with the imate cid settings in it? i don't remember.
i'll post a rom that i think may have helped in a few hours, I have slow upload speed. until then, just keep tinkering.
also, you should only be flashing nk.nbf. not the ms, or radio nbfs.
http://milfweed.info/UNI_AKU3_2_WWE_IVAN_beta_4_extrom_public.rar
try that rom.
hey man.. Flashed the rom with Ranju's ROM of WM6.1.. it worked.. But I can get the phone to be turned on. i mean device turns on but I can't make or receive calls or text. Let me check the thread of that rom. Thanks a ton for your support. Really appreciate it.