I use the k-jam alot. and after taking the pencil out and back in again it has got so loose now that it usually drops out. any one else hade same problem and how did you resolve it?
I had same problem with my BA. I'm not sure the wizard has same retention tab, but if it does, then this works.
-Back up your data.
-Remove the cover you will find a small tab in the stylus channel intended to engage the notch cut into the stylus. Gently push the tab back into the stylus channel so that it will engage the stylus notch once again. Be careful if you push it too far it will break.
-Slide the stylus into the channel to verify that the tab again engages the stylus notch.
-Remove the stylus again.
-Apply a small dab silicone sealant (available at any hardware store) behind the stylus retention tab. This is the "V" shaped area between the tab and the case. Be sure to fill this entire area. When the silicone has cured it will become a spring with much better position memory then the original plastic tab had on its own.
-Allow 24 hours for the silicone to cure before inserting the stylus into the channel.
I believe this is more then a repair, it is an upgrade.
Good Luck,
N2O2
Thanks for the tips.
I was just thinking of what to do when i came acroos some bluetac .
I put some blutac in the hole were the stylus goes and pushed the pen in. and it was a miracle !!! The stylus stayes in with a good hold and it comes out clean with no bluetac on it.
whe the bluetac trys to come out it has no room coz the stylus filles the space so it stays in the edges and grips the stulus pen and keeps it from getting loose. .
problem solved !!
Nice Catch
I put some blutac in the hole were the stylus goes and pushed the pen in.
Click to expand...
Click to collapse
Gave the Bluetac method a whirl on my K-Jam after the stylus starting dropping out. Works a treat..
Nice one.
Nice Catch
I put some blutac in the hole were the stylus goes and pushed the pen in.
Click to expand...
Click to collapse
Gave the Bluetac method a whirl on my K-Jam after the stylus starting dropping out. Works a treat..
Nice one.
Yes it does.
Easy and simple way of not opening or messing about with k-jam to void warranty.
I mean. you will not viod waranty this way, but will if you open the k-jam
one time around the stylus with some tape works great to.
But what happen if the blutac starts to ware off?
But what happen if the blutac starts to ware off?
Click to expand...
Click to collapse
Then I'll pop the case :shock: , extract the bluetac and do the silicone mod.
I'd be surprised if it does wear off though. It's superb stuff that's saved me a few quid in the past when in rented accomodation - bluetac and tippex to create the illusion of undamaged walls :wink:
Can you please give me a hint what "bluetac" is or means ?
I have dismantled mine, and I can see why this is breaking - see my post regarding the sylus silo.
when the stylus is getting loose, when you are pushing it in do you "feel" it going further forward than it did before?
It is because the plastic tab is not strong enough to resist the pen, and you are now pushing it further forward than you did before.
This is what causes the stress on the plastic, and then the crack. This black plastic part is molded to the entire back of the phone.
I have fixed this by wedging some folded paper behind the black plastic clip, and it is back to normal. I was lucky - I had not stressed mine enough that the plastic had cracked.
I have taken some photos of how to get the back off, I will post them when I return from my business travel.
Jon
Can you please give me a hint what "bluetac" is or means ?
Click to expand...
Click to collapse
Ignoring my [email protected] spelling (should be "Blutac"), it's this stuff: http://www.paperstone.co.uk/BrowseProductDisplay.aspx?ProductId=17307&CategoryId=579-580-594
I'd be interested in seeing the photos on how to dismantle.
It is because the plastic tab is not strong enough to resist the pen, and you are now pushing it further forward than you did before.
This is what causes the stress on the plastic, and then the crack. This black plastic part is molded to the entire back of the phone.
I have fixed this by wedging some folded paper behind the black plastic clip, and it is back to normal. I was lucky - I had not stressed mine enough that the plastic had cracked.
Click to expand...
Click to collapse
I have now started collapsing the stylus before inserting it into the hole so it doesn't push against the end and only goes as far as the moulded plastic bit at the top.
just wrap a piece of tape around the stylus and it fits like a glove again.
leploep
This is only a temp fix, did that and after a week or two back to the stylus dropping out. I am waiting for the pics on how to get the back off and do a more permanent solution, you would think Imate would have caught this in their product testing phase before going to production.
sunseaker said:
I have now started collapsing the stylus before inserting it into the hole so it doesn't push against the end and only goes as far as the moulded plastic bit at the top.
Click to expand...
Click to collapse
I've always done this as it does not seem to fully shink other wise... seems Ok so far.
marka2k said:
leploep
This is only a temp fix, did that and after a week or two back to the stylus dropping out. I am waiting for the pics on how to get the back off and do a more permanent solution, you would think Imate would have caught this in their product testing phase before going to production.
Click to expand...
Click to collapse
Personally I think on the bottom of the phone is daft in the first place... or is this just me ?
Terran
the pics are in the upload folder, called wizardpics.zip - the ftp upload attachment does not seem to be working?
to remove the top half I used a flat knife. It is quite resistant. You can see where the tabs are in the pic.
To remove the back completely, you need to remove the void sticker, and under there is a screw. there is also one opposite.
You will also need to remove the 2 screws at the bottom, one in the stylus channel, and the other on the opposite side.
then use a plastic splitting tool if you have one, or a credit card to work round the case.
you can see in the pics where this comes off.
You then want to re-enforce behind the stylus notch. I used a piece of folded card.
chakra said:
one time around the stylus with some tape works great to.
Click to expand...
Click to collapse
where exactly are you putting the tape which end
i did the blutac thing but might have put too much in cos the grey plastic end i use to pull stylus out just broke!
Related
OK managed to snatch one of the only/few tilts available in my area last Friday and now, after a week of use I've noticed I hate the ATT case I bought: The leather, plastic clip, top-loading case, SUCKS!
I work in an ER so speed, quality, ease of use is paramount. My major problem with this case is that 1. I press buttons trying to pull it out and 2. the belt clip is not centered well so when I try to orient it horizontally on my scrubs the opening end tips downward toward the floor.
SO, I've been searching around the forums, looked at a TON of different cases. So far I like the look of this: http://www.pdair.com/catalog/product_info.php?cPath=10100000_900000_11000164&products_id=6562
BUT I don't like the plastic over the keyboard and how annoying is that flap when you're trying to talk on the phone? I don't want to be fiddling with a GD flap while talking. Does the flap flip all the way back on itself?
SO, I need a well-balanced, high quality plastic clip (quick releases are good), that does not have cumbersome flaps (or at least has flaps that fold back on the case/go away when used as a phone).
Thoughts?
Thanks
Does this case work for you?
http://www.boxwave.com/products/dlsleeve/htc-kaiser-designio-leather-sleeve_2642.htm
I received mine this week and am satisfied. There is no hole to access the reset button, but that's a minor issue.
skins07 said:
Does this case work for you?
http://www.boxwave.com/products/dlsleeve/htc-kaiser-designio-leather-sleeve_2642.htm
I received mine this week and am satisfied. There is no hole to access the reset button, but that's a minor issue.
Click to expand...
Click to collapse
It seems that you can't slide the keyboard out when using this case... am I mistaken?
h0mersimps0n said:
SO, I've been searching around the forums, looked at a TON of different cases. So far I like the look of this: http://www.pdair.com/catalog/product_info.php?cPath=10100000_900000_11000164&products_id=6562
BUT I don't like the plastic over the keyboard and how annoying is that flap when you're trying to talk on the phone? I don't want to be fiddling with a GD flap while talking. Does the flap flip all the way back on itself?
Click to expand...
Click to collapse
I don't know about the book-style case, but I have the PDAir flip case, which has the flap hinge at the bottom. On that case, the front flap folds back very nicely. The snap strap on the top that holds the front flap closed doesn't fold back so well, but I've only had the case 2 weeks so it'll probably loosen up a bit over time.
dweinstock said:
It seems that you can't slide the keyboard out when using this case... am I mistaken?
Click to expand...
Click to collapse
To slide the keyboard, you do need to unsnap the cover and fold it back. The phone can still be left in the case. I rarely use the keyboard, but this could be a major issue for those that do.
skins07 said:
Does this case work for you?
http://www.boxwave.com/products/dlsleeve/htc-kaiser-designio-leather-sleeve_2642.htm
I received mine this week and am satisfied. There is no hole to access the reset button, but that's a minor issue.
Click to expand...
Click to collapse
Do you have any pics with your phone in it?
Have you had any problems with the belt clip screw coming loose?
I think I need something that protects the screen too... I'll have to think it over...
3WAYGEEK- thank you for the reply- that's exactly the info I was looking for, now I just need to find someone who has the side flap...
Thanks guys
h0mersimps0n said:
Do you have any pics with your phone in it?
Have you had any problems with the belt clip screw coming loose?
I think I need something that protects the screen too... I'll have to think it over...
3WAYGEEK- thank you for the reply- that's exactly the info I was looking for, now I just need to find someone who has the side flap...
Thanks guys
Click to expand...
Click to collapse
Sorry, I have no pictures. There are images without the phone on the Boxwave site.
There have not been any problems with the clip and screw.
I do use a screen protector, but this case does leave the screen open, a feature I was seeking.
I'm hoping someone might have a helpful suggestion other than "take it apart." I've been using a stylus / pen that I got off ebay. The ball point pen is hidden under a cap at the opposite end of where the stylus point is.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&rd=1&item=190199301645&ssPageName=STRK:MEWN:IT&ih=009
It works great except that the cap came off while the stylus was inside my advantage --- and now, I can't get the stylus out. It's stuck, and there's no way to reach in and get it.
Any thoughts??
Thanks
I think you could put some glue (very little) inside the cap and then put it (the cap) into the HTC stylus hole. After a time take it out and then try to remove the glue (dissolving or smthg like that). Peter.
Thanks, I'll try that!
pkchainsaw said:
Thanks, I'll try that!
Click to expand...
Click to collapse
Just be careful not to touch the sides while sliding the pen in, or it will get very messy in there and harsh when the glue dries and come time to put a new stylus in. Thanks for the heads up because I was going to purchase a pack of 3 in 1 pens. I won't now due to the fact that it can come apart.
tootallk2000 said:
Just be careful not to touch the sides while sliding the pen in, or it will get very messy in there and harsh when the glue dries and come time to put a new stylus in. Thanks for the heads up because I was going to purchase a pack of 3 in 1 pens. I won't now due to the fact that it can come apart.
Click to expand...
Click to collapse
WOW!! IT WORKED!!!! THANKS!
Of course, do what you think is best, but I'm going to keep using it. I think the fault was mine, not the pen's.
THANKS AGAIN!
Does that stylus actually fit completley into your advantage? I have the exact same 3 pack sitting at home, ordered off ebay, and its just not capable of fitting into the slide on the advantage. Not to mention how shoddy the quality appeared to be with regards to how the 3 pieces stick together. I mean its obvious when you mix metal with plastic threads...things are gonna work loose very quickly. Anyway, I just ordered a 3 pack of 3in1 stylus from expansys that they are advertising as an exact fit, made specifically for the advantage, as well as a 3 pack of oem stylus just to make sure heh.
Mine does all the time. Its a major week point of the phone. Apart from that and the delete key in Opera (will install the beta of 9.5 to resolve this) the phone is near perfect.
It literally jumps off the phone in my pocket, I put it really nicely on the desk and when I pick it up, it has jumped off again. Hold the 4 corners and move one really (i mean really) slightly and the cover pops off.
The plastic clips where I have put the back on continuously are starting to wear down!
Anyone else get this or is it just me?
Yes mine did when I first got it. Easy fix though.
Take the back cover off, where the two interior clips are housed in the cover ( bottom part of cover lined up with the indents on the phone to allow removal of the cover) give it a good squeeze to bend the metal cover in by pushing both sides.
Worked a treat for me.
Thanks, you have made me look stupid
Works a treat!!
While we're on the subject of battery covers, do you guys have any idea what's up with the metal contacts making connections to the battery cover? Is it some kind of grounding thing? maybe an extensible connection of the antenna, or using the batt cover as wifi antenna or something? Hah, but really, it seems odd.
Good tip though, this thing is stuck on there now!
Nope, but the tip is good.
Jump? Mine has a little 'bump' in the middle, a slight outward curve. Took it to 2 service centres and they said it's normal.
matthewf01 said:
While we're on the subject of battery covers, do you guys have any idea what's up with the metal contacts making connections to the battery cover? Is it some kind of grounding thing? maybe an extensible connection of the antenna, or using the batt cover as wifi antenna or something? Hah, but really, it seems odd.
Good tip though, this thing is stuck on there now!
Click to expand...
Click to collapse
Is it to know if the cover is off?
xpear-e-ah said:
Yes mine did when I first got it. Easy fix though.
Take the back cover off, where the two interior clips are housed in the cover ( bottom part of cover lined up with the indents on the phone to allow removal of the cover) give it a good squeeze to bend the metal cover in by pushing both sides.
Worked a treat for me.
Click to expand...
Click to collapse
Sorry could you explain a little more...i'm a bit blonde haha. The clips on the actual battery cover? where do u bend the metal...like forward, inwards? etc thanks
edit: Nevermind, after taking it off a few times it fits fine now
zoelucker said:
Sorry could you explain a little more...i'm a bit blonde haha. The clips on the actual battery cover? where do u bend the metal...like forward, inwards? etc thanks
edit: Nevermind, after taking it off a few times it fits fine now
Click to expand...
Click to collapse
upside down, your battery cover looks, in profile, roughly like this:
|____|
You want to bend the sides in, on the end where it says SONY ERICSSON, in this manner:
--> /____\ <--
(Don't bend it to such an extreme degree as depicted though, of course! Just an indication of what direction you're bending in...)
matthewf01 said:
upside down, your battery cover looks, in profile, roughly like this:
|____|
You want to bend the sides in, on the end where it says SONY ERICSSON, in this manner:
--> /____\ <--
(Don't bend it to such an extreme degree as depicted though, of course! Just an indication of what direction you're bending in...)
Click to expand...
Click to collapse
I had the same problem. This is how you solve it.
Dont just bend it in the MIDDLE or else you'll deform the entire cover.
xpear-e-ah said:
Yes mine did when I first got it. Easy fix though.
Take the back cover off, where the two interior clips are housed in the cover ( bottom part of cover lined up with the indents on the phone to allow removal of the cover) give it a good squeeze to bend the metal cover in by pushing both sides.
Worked a treat for me.
Click to expand...
Click to collapse
^^^
This guy is a superstar
Anyone got any tips for getting a stylus in which the top part has snapped off of out of the magnetic stylus holder on the phone?
I bought some spare ones as I always lose them but upon using these spares I found they all suffer from the same problem, the plastic top and bottoms snap off very easily.
So now I have no stylus, but part of a stlyus stuck inside my phone.
Any help much appreciated.
Thanks
If you remove the battery cover you will see 2 sections where you can see the stylus. You use some long thin object and try to wedge it out.
Not on my phone there isn't.
I can see it in 1 place about half way up but the battery doesn't need to be off for that.
I can't think of anyway to get anything that is going to get any grip on it to get it out...
Take the battery cover off, you'll be able to see the stylus in its sheath. Use a bit of sticky tape to grab the stylus and slide it up and out. Hope this helps.
Put some super glue and put the stylus back.
I am very curious.
Use tweezers
berbecverde said:
Put some super glue and put the stylus back.
I am very curious.
Click to expand...
Click to collapse
I think that may well have to be the way to do it.
I can't get any grip the other ways.
I'll try it!
barryfell said:
I think that may well have to be the way to do it.
I can't get any grip the other ways.
I'll try it!
Click to expand...
Click to collapse
Just remember that a little bit will go a long way...don't want to see a 'Super glued stylus stuck in phone' thread...
Yes that is right.
Not too much glue if you want to try.
Keep us posted.
well that is what I was afraid of when I bought the note, the paint job of the bezel disappointed me, especially at the headphone plug, it seems that the paint job is really poor, i ended noticing that the paint started to flicker, what a disappointment i hope that it will not get bigger.
I almost knew from the start that it would flake easily especially at weak points like plug in areas, i wish to know how to fix it, but i saw some video and taking it appart is hell, maybe i should consider giving it a brushed look bezel
hykhleif said:
well that is what I was afraid of when I bought the note, the paint job of the bezel disappointed me, especially at the headphone plug, it seems that the paint job is really poor, i ended noticing that the paint started to flicker, what a disappointment i hope that it will not get bigger.
I almost knew from the start that it would flake easily especially at weak points like plug in areas, i wish to know how to fix it, but i saw some video and taking it appart is hell, maybe i should consider giving it a brushed look bezel
Click to expand...
Click to collapse
I.had mine about a month.no paint issue.never put hard cover on any samaung device.it will peel paint off from bazel.i learned the hard way putting on my infuse.i had tp replace the whole bazel and about 5 min.
mintu123 said:
I.had mine about a month.no paint issue.never put hard cover on any samaung device.it will peel paint off from bazel.i learned the hard way putting on my infuse.i had tp replace the whole bazel and about 5 min.
Click to expand...
Click to collapse
I've had my Note for around 3 months.
2 weeks back I was sick, having fever, throat & ear infection.
I took a visit to the hospital and unfortunately dropped the phone whilst sitting down.
I was so sick & weak the phone slipped whilst in my hand.
Thankfully the damage was minimal. The only minor mark was on the upper left hand corner of the bezel, a slight discolouration.
I too would like to change my bezel.
Would you be kind enough to post a link to a video which shows how to dismantle the bezel & then put back?
Thanks.
kanej2006 said:
I've had my Note for around 3 months.
2 weeks back I was sick, having fever, throat & ear infection.
I took a visit to the hospital and unfortunately dropped the phone whilst sitting down.
I was so sick & weak the phone slipped whilst in my hand.
Thankfully the damage was minimal. The only minor mark was on the upper left hand corner of the bezel, a slight discolouration.
I too would like to change my bezel.
Would you be kind enough to post a link to a video which shows how to dismantle the bezel & then put back?
Thanks.
Click to expand...
Click to collapse
just get it from ebay,its like $30 original.its very easy.remove battery sim and sdcard and remove 9 screws and use ur thumb under the battery and carefully push screen part out.there is a guide in general how to replace a screen.
mintu123 said:
I.had mine about a month.no paint issue.never put hard cover on any samaung device.it will peel paint off from bazel.i learned the hard way putting on my infuse.i had tp replace the whole bazel and about 5 min.
Click to expand...
Click to collapse
no hard cover...you mean no hard cases for Note?
mintu123 said:
just get it from ebay,its like $30 original.its very easy.remove battery sim and sdcard and remove 9 screws and use ur thumb under the battery and carefully push screen part out.there is a guide in general how to replace a screen.
Click to expand...
Click to collapse
Thanks a bunch!
Every bezel ive come across is a piece of ****.
Sent from my GT-N7000 using xda premium
tytung2020 said:
no hard cover...you mean no hard cases for Note?
Click to expand...
Click to collapse
Yes.dont use hard case.if u have to put case on it use them rubber cases.
are you sure that its easy to replace the bezel, are there no wires or stuff to take apart when changing the bezel. So its only removing the 9 screws.
hykhleif said:
are you sure that its easy to replace the bezel, are there no wires or stuff to take apart when changing the bezel. So its only removing the 9 screws.
Click to expand...
Click to collapse
My first Note went for a swim with me in salt water so naturally I tried a few things to get it working again, including removing as many components as possible. The bezel is part of the back cover that the battery sits snug against on all edges, and if you use both thumbnails to separate the screen from this bezel/backplate then it should come off after a bit of manipulation.
IMO it's not worth replacing as one mistake will cause another mark and you'll never be satisfied with it unless it's as new. I've found that only after you get a few nicks and bumps that you actually use it like it's meant to be - used. It's not being careless but spending more time using it than being super cautious is where it's at.