Hello all,
I'm considering moving up to the XDA Exec; especially now that I see many contributors here have worked out how to get it running well.
However I suspect that, with its bigger size, using a bluetooth headset will be even more important. My experiences with my XDAII were that it was never quite reliable enough to use day-to-day (even after trying different bluetooth stacks etc.)
So what are your experiences:
- does it work well
- how about the voice dialling via bluetooth
- caller id on compatibale headsets work?
cheers,
Pete
I'd say it depends on your headset, but yes: The Exec handles my Bluetooth headset more reliably than my XDA2 did.
I've got a SonyEricsson HBH-65 that was occasionally great and occasionally infuriating with my XDA2, but it seems much happier with the Exec. It's not perfect since it's tough to interpret the various bleeps and boops that the headset gives out and understand what they mean, but I'm getting used to it. It'd be a lot easier if the headset makers could give us more than one button... :roll:
With my HBH-65 and my Exec I can receive calls and use voice dialling to make calls (provided I've configured the voice dial commands already). The voicedial bleeps are a bit quiet in the headset but trial and error might improve things.
Some people seem to have problems using voicedial if their Exec is closed and turned off, but I don't seem to have the same problem. The first press of the headset button switches the Exec on and then a second one gives me the voice prompt.
Hope this helps
I've tried a Bluespoon AX and a Plantronics Discovery 640 with my headset and while they both appear to work fine functionaly, the quality of the audio is bad. I've tested the same bluetooth devices with other phones and the quality is much better.
Does anyone else have this problem? I'm going to go into to O2 later today and see if they've had reports of this before. Maybe I have a dud device.
I have an Exec, a Jasjar *and* an MDA Pro the Exec is mine, the rest is Eval.) and the Exec and MDA pro handle BT Headset fine. The Jasjar however keeps dropping the connection between the device and the headset. Flashing the MDA Pro with the Jasjar ROM made that the Pro also started dropping the connection between device and headset.
Conclusion, something is flaky in the Jasjar Rom.
There are a number of posts relating to this dropping of connection in this forum.
G'day
I have had the Jabra BT800 for a few months and never used it as it was pointless with the XDA IIs, but it works perfectly with the JasJar. It even rings about half a second before the phone does and shows the callers number (pitty it doesnt show the name from the phones contacts).
I am happy i didnt sell the BT800, as now i can keep the JasJar closed in my pocket when i just need to answer the phone.
Paul
ive used a jabra bt250v no problems voice dial is much better and works fine but i havent found how to get the audiogaeway working any ideas anyone so i can get tomtom throught the headset
JJ and Jabra BT 800 work well and voice dial works very well. Have made 1.5 hours in the last two weeks and not dropped calls. When used inside a car or in a room the signal is okay but as soon as you use the Jabra BT800 and JJ outside the signal gets weaker.
Related
Hi all,
First post for me, but i've been hiding in the wings for ages.
Anyway, just for your info, the JABRA BT250 works perfectly (Headset profile).
Once bonded with the XDA2, it doesn't loose any connection, even after charging.
Once the XDA2 and BT250 are bonded nothing seems to stop them working together.
Roll on the Hands free profile tho...
Sno...
Hi,
I can confirm the above. I was really worried about trying to get a BT headset to work after reading about all the problems other users have had in the past.
I bought a Jabra BT250 for £79.99 from my local o2 shop in Bristol.
Works perfectly. Bonds with no problem. Has kept that bond even after soft reset on XDA and charging / turning off etc on the BT250.
Highly recommended. 8 hours talktime and 240 hours standby on one charge of the headset.
Steve
I'm using the BT250 also with no connection issue. However, I'm experiencing some slight static noise when the BT Headset first starts up. Are other people getting this issue as well?
gratefuled said:
I'm using the BT250 also with no connection issue. However, I'm experiencing some slight static noise when the BT Headset first starts up. Are other people getting this issue as well?
Click to expand...
Click to collapse
I only experience this (actually it's more a sort of distortion) when my battery is under 55%.
Further I can only second the opinions of the above posters: Using a BT 250 for a while now with my MDA II. Really recommended!
Does it work w/ Microsoft Voice Command???
No BT headset will work with Ms Voice Command at this time.
I own a XDA, MDA II and a HP6315. I've given my MDA II to my wife cause I bought the 6315 when it came out.
I'm here to tell you the at the bluetooth stack may have more function, but the headset profile sucks. 40 % failier rate getting the BT Headset to pick up during an incomming call. It's like the BT Headset and the HP 6315 come disconnected during a period of inactivity.
I think everyone should be aware of this before making their decision to move over to a HP6315. Unless they find a fix for the problem, you'd be trading a BT Stack that works 90% of the time in the headset profile for one that works 60% of the time.
Oh.. And if you get it to work, MS Voice Command doesn't pick up very well over the BT Headset on the 6315. It's not there yet.
If it wasn't for a full LDS Scripture set (www.yanceyware.com) and Microsoft Money (syncable) I'd be using a Symbian Phone today. No BT Profile problems there. Plus there's GPS apps for my BT GPS on them.
I have to say that I have not had the same experience with my h6315 and SE HBH-30 BT headset. I have been quite pleased with the performance of the headset profile - it performs better than I expected - and better than that on my i-mate.
I agree w/Brosenow. The BT reliability on the 6315 has been FAR superior than my xdaII.
I used the same headset, my hbh-65 on both & the soundquality is better too...not to mention if the pairing is dropped during a conversation(which happens on both), the 6315 at least retrieves the conversation immediately & my xda2 never did that...Then there's the lack of ability of switching manually from headset to phone on xda2 which was a "cluge" ...then throw in BT "audio", handsfree profile, PAN, PORT...it's really no contest in BT alone even tho everything else in the xda2 hardware (screen, proc.) is nicer...guess I shouldn't have dropped it then, huh? :lol:
I am soon to buy the Magician in one of it's many forms. However noe thing i have been woundering is how am i am going to achieve the in-car setup i desire. Basically I need both a carkit (conversation through car stereo speakers etc) and i also want to run GPS navigation on the Magician. First of all is this possible? What happens if i am using the GPS and i recieve a call? Also what hardware are people using to achieve this as i assume i can't use both a bluetooth carkit and a bluetooth GPS reciever?! any hlp is greatly appreciated.
Thanks,
Tom
Hi Tom,
I've got an iMate Jam & recently installed a Parrot BTluetooth CK3300 GPS Car Kit into my 1999 RAV4. The installation was pretty straight forward for cars with ISO connection, simply put in the mic, GPS ant & control display, plug into the car harness & HiFi & off you go. The GPS part of the kit is simply & effective, I use Tom Tom Navigator 5 & it's pretty faultless, obtaining a fix in seconds. Here's the bad part, the call quality through the kit using the Jam is AWFUL. Making and receiving calls is accompanied by a loud, high pitched warbling sound which eventually subsides, but is replaced by so much interference that the call is unworkable. I know it's not the kit because my wife's SE T68i works flawlessly. Everything else about the setup works perfectly (pairing muting, upgrading via BT etc etc). This a MAJOR problem which I have sent on to Parrot & am waiting for a reply. I understand they are pretty good at customer enquiries and expect them to come back to me pretty soon. I'll post again when I hear something. Despite all the bad press the Jam gets I think it's the best one I've owned so far (I'm on my 5th) and with the right software is excellent, but the choice of car kit is essential, until these problems are ironed out I wouldn't recommend using the PDA with a BT carkit.
Apart from the poor audio, how does it work when you are being navigated by TomTom and you receive a call? Does TomTom stop talking to you? Does the display show who's calling and then go back to tomtom display etc?
Hi there,
I have a MDA compact with now the QTEK 1.12 ROM, I have a bluetooth GPS Fortuna Clip-on and a Mr Handsfree Genius Bluetooth Carkit and I love it.
As soon as I start my car, there is a bluetooth connection to the carkit and the sound quality is excellent. You can make a call without getting the MDA out of your pocket, just push the button. The only issue is voice dialing, but that is a common problem for the MDA.
Also it makes a bluetooth connection to the GPS and Tomtom works fine. The only minus is that Tomtom doesn't use the carkit speaker, but, since the speaker of the MDA is loud enough, that is no issue. There is no supply with this bluetooth carkit, so I bought a 12 --> 5 Volt converter for the MDA.
I really love this combination. The best thing, that happened to me.
Andre
Hi there,
I have a MDA compact with now the QTEK 1.12 ROM, I have a bluetooth GPS Fortuna Clip-on and a Mr Handsfree Genius Bluetooth Carkit and I love it.
As soon as I start my car, there is a bluetooth connection to the carkit and the sound quality is excellent. You can make a call without getting the MDA out of your pocket, just push the button. The only issue is voice dialing, but that is a common problem for the MDA.
Also it makes a bluetooth connection to the GPS and Tomtom works fine. The only minus is that Tomtom doesn't use the carkit speaker, but, since the speaker of the MDA is loud enough, that is no issue. There is no supply with this bluetooth carkit, so I bought a 12 --> 5 Volt converter for the MDA.
I really love this combination. The best thing, that happened to me.
Andre
so it is possible then to have two bluetooth connections running at the same time? ie. i can use a bluetooth GPS reciever such as the one that is supplied with tom tom and also use any bluetooth carkit at the same time? and this will not cause any problems even if i am making a call and have the GPS running?! If so then i will probably just buy the Tom Tom 5 bluetooth kit and get something like a parrot CK3000? would this setup work?
thanks for everyones help,
Tom
It should work. Mine does. See above. Bluetooth GPS uses a serial profile, bluetooth headset uses a headset profile. No problem to use them both at the same time.
Andre
I used my Jam as phone, mp3 player and GPS all at the same time.
1. MP3 thru my car's aux input
2. GPS thru aux input:
hardware: Tomtom BT receiver
Software: Routis 2, TomTom USA 2004 (can open both if U use GPSGate)
3. Phone thru BT headset or aux input
To answer yr question:
Since I can use both BT GPS and BT headset together. I don't think it's a problem for both BT carkit and BT GPS to works.
Phone call always get highest prioity, all other apps (GPS software, mp3 player) will be mute until U finished yr call.
Phone call is not a problem (see above) but dialing is a big trouble since no voice calling built-in. Third partner software like intellidialer and voice commander (from MS or Cyberon) helps a bit
Ive also got my jam working fine incar. I use a socket bluetooth gps unit http://www.expansys.com/product.asp?code=119717 with tomtom 5 then I have a SE HBH-600 Akono Bluetooth Headset for calls both work together! When I have a incoming call it mutes tomtom and displays the normal caller id app on top, answering the call (via the green hardware button) results in my jam going to the phone app totally and leaving tomtom minimized in the background. As soon as the call ends tomtom jumps back to the foreground, it all works very well in my opinion. Ive also assigned the camera button to switch me back to the today screen so I can launch any app (with tomtom still running in the background) via a icon.
Hi all,
I have an MDA II and a Plantronics M2500 BT headset. So far so good....
I managed to connect them together, and after some work (bonding, etc.), I was able to phone using my headset.
However, I have the following problem:
If I switch on my BT headset and enable BT on MDA II (so BT 'on', BT headset mode 'enabled'), the 2 devices do not automatically connect.
I have to 'play around' a bit, e.g. by disabling/enabling BT headset mode, turning BT settings on/off/discoverable, turning on/off the BT headset, and try calling some numbers for testing before it works.
After a short while (and if I'm lucky , I can call and receive calls using my headset.
This is of course not the ideal situation. I'd like to have the devices work automatically as soon as I turn them on.
I have the suspicion that this is a bug.... Did anybody else have similar problems and does anyone have an idea how to get this fixed?
Oh yeah: I am using a BT GPS mouse as well for TomTom 5 and this device is also bounded to the MDA II.
Thank you very much in advance!
BTW: the quality of the BT headset (once I get it working) is pretty good, so no problems there...
Yep, one of the problems with (some) BT sets...
Didn't have is with a Sony Errocson HBHxxx, did with a Jabra, didn't with a Supertooth2 etc....
Try the famous BTtools, it often helps...
Or get another headset
Hey! just wondering, what do you guys recommend for a good bluetooth headset for XDA exec?
I have the Jabra BT250V and find it the best for me, I have not tried any other brands other than the Bluespoon AX (that was to hard to get on in a hurry and allthough its small I found it looked stupid hanging out of the ear.
I have a Jabra BT500 and love the shape but am having problems pairing it with my Jasjar it was fine for a while then after an upgrade I couldn't pair it with the phone. I also found it to be alot harder to hear than the BT250v and I love the vibration in the 250V as you know weather or not the bluetooth is still active as it is a bit unrealiable on the Jasjar.
I'm really pleased with my Jabra BT800. Excellent battery life (2-3 days, 2 hrs per day), superb sound quality (and positive comments from people even when I'm in a noisy environment), good control with the built-in screen and plenty of buttons, comfortable etc.
Only restriction at the moment is the lack of caller name on the screen. Just have the caller's phone number at the moment. I think this is the Universal's fault though, and I fully expect it to be fixed with a ROM update.
Bluetooth is perfectly reliable for me on my XDA Exec with this headset. My old Sony HBH-65 was much less reliable: almost unusable.
I agree with Silicon the BT800 is a good headset and works for me okay with my Exec. But I have found the cheaper SE HBH-608 has a much better battery life (usually 5 days) and is lighter and more comfortable, but it does not have a LCD. A BT headset with a LCD is a must I think when using the Universal. The Caller id I think need the headset BT profile which I am not sure will be in the next ROM upgrade. Finally, I would also recommend you look at the Tekkeon ET3000 (if you are in the USA) and the latest SE headsets with advanced DSP and LCD displays.
I have the V3 BTH-8 OLED headset.. Sadly, it just shows the number but not the caller name for Dopod. Supposedly, it will be able to offer function to browse phone book thru headset, but I guess that's for other phones not for our wonderful phone
Globalsat BTH-818 . Much more moderate than the brick from Jabra. Otherwise same functionality (minus the vibrator). Much better battery time too.
Which one is the smallest bluetooth headset at this moment? I like small one.
I love my Sony Ericsson HBH-300 Akono headset. To be honest compared to some they make these days it looks quite large, but battery life is fantastic and sound quality amazing. I've never been a fan of the ones where microphone is nowhere near your mouth, but that's just me.
Oh and it's large enough so people can see I'm actually on a headset and not talking to myself, but not so large it's uncomfortable to wear (quite opposite!)
Great! Thanks for all your replies! I've placed an order for Tekkeon ET3000. It should be here by late this week or early next week. I'll see how that BT headset goes! 8)
seal said:
I have the Jabra BT250V and find it the best for me, I have not tried any other brands other than the Bluespoon AX (that was to hard to get on in a hurry and allthough its small I found it looked stupid hanging out of the ear.
I have a Jabra BT500 and love the shape but am having problems pairing it with my Jasjar it was fine for a while then after an upgrade I couldn't pair it with the phone. I also found it to be alot harder to hear than the BT250v and I love the vibration in the 250V as you know weather or not the bluetooth is still active as it is a bit unrealiable on the Jasjar.
Click to expand...
Click to collapse
I don't know about you, but I had this headset and only had issues with this particular one. Mainly static. It just did not sound great, even with the device only a foot away I had severe static. I don't recommend this unit to anyone. Even my wife stated that I sounded as if I were in a tunnel.
Everyone I've had stinks.
I cannot recommend anyone to you since every one I've had really caused severe static. I've had the Jabra BT 250v and it had static, I have the Motorola H700 and again, static. I don't know if it's my Qtek 9000 bluetooth stack or what, but I'm using a wired headset without any difficulties and the sound is incredible. I am fed up with fighting with the bluetooth headsets if I can get two of the most popular (and expensive) ones to work with my $1000.00 "phone."
ronaldf117 said:
Which one is the smallest bluetooth headset at this moment? I like small one.
Click to expand...
Click to collapse
Plantronics Voyager 640 and Jabra JX10.
I am somewhat "stuck' with a Motorola HS850 since it's the only one that works with MS Voice Command.
Motorola HS850 i been using, the boom is cool flick it in and out to answer/end calls. Its a good head set saves you from wearing it all day. It folds away nicely in you pocket and has decent battery life.
Only bad thing is though it takes alittle time to wake up once you lower the boom but always switched on works fine.
Hi
I'm using an (old) Sony Ericsson HBH200 and the big news is since i upgraded to the latest Orange ROM 1.30 (from Dopod 900), i can now get caller ID and access the phone call list from the headset. (PS:i have also a Jabra 800 and i did not manage to get the caller ID but i did not insist that much as i much prefer the HBH200). No need anymore to open my phone
cheers
Sailornono said:
Hi
I'm using an (old) Sony Ericsson HBH200 and the big news is since i upgraded to the latest Orange ROM 1.30 (from Dopod 900), i can now get caller ID and access the phone call list from the headset. (PS:i have also a Jabra 800 and i did not manage to get the caller ID but i did not insist that much as i much prefer the HBH200). No need anymore to open my phone
cheers
Click to expand...
Click to collapse
You mean caller "NAME" or caller "NUMBER"? Which is showing? :?:
i've done some more test, it appears that the HBH give access to the call history including full names, phone number and date of outgoing or incoming calls.
Actually this is exactly the liste you can see in call history from the Universal.
That's something new from my former dopod ROM
On incoming calls, it seems that it still displays only the phone number not the full name, that is still to be confirmed for local numbers as i used internationnal call to make the test.