hi guys..
I was watching a video clip and suddenly I see I can't hear any audio from it. I was surprised.. I tried to soft reset it couple of times... but with no luck... I couldn't here any tap sound or even when the phone rings.. nothing sounds.. and finally I did hard reset... but in despair.. still the same problem. but when I try to shake my jam. I could feel something moving.. i don't know if any bit/piece is disconnected.. when i try to tap it hard at the speaker.. i could hear to the music and after few seconds.. its stops.. again..
Has anyone come across such a problem.. I think probably my speaker needs to replaced.. any suggestions or solutions to this..
I would await for ur replies.
kindly advise..
thanks
Iffu
i have the same problem to. Please Help!
This is a "common" problem with the Magician. Mine had it as well. I sent it for repair since it's still under warranty. Some ppl had the guts to open it and fix the loose contact themselves. So if you're not a techie just take it to your service centre for repair :-(
No sound?
Hi. i had a similar problem some days ago. no sound at all from my magician. i've discovered that the problem was that my magician thought i had headphones conected. a simple insert of a headphone jack and removal brought my sound back to live. No problems since than.
Just a gentle few bangs did the trick
After reading several suggestions and info about the speaker problem, I tested my 02 mini with a song. It played ok through the speaker. So the speaker works, but appears to not "Switch" on when being used as a phone. Anyway long story short - I hit the corner of it into the palm of my hand a few times and da da it works again. I also blew through the speaker hole. Someone mentioned that somewhere as well. Hitting into my hand seemed to provide enough impact without creating any damage.
Had same problem too, and sent it away for repair. Three weeks later and the repair company are sending me a replacement this week as apparently they were unable to fix it!
Fault appeared without any warning and I had been using the phone pretty heavily all day. All I hope is that the replacement will have a newer ROM installed to save my ineptness from screwing up an upgrade.
This Jam is a peice of shi#e. I bought one in February, had various problems with both speakers - regular earpiece was unclear and speaker phone was just too damn low in volume.
Some people claimed this was an exception, or that it was the ROM or whatever. Right......
Finally sent the Jam back for warranty repair in May- there were many other defects with the phone that accumulated. I had bought insurance as well so I told them to just replace it. The seller admitted that this (audio/speaker is a common problem in this phone)
I just got the insurance replacement today - yep ages later. This one has firmware 1.11 WWE.
Guess what: the speakerphone on this one (brand new replacement) doesn't work - at all. Not at all. This is brand new, out of thebox. Incredible....
What is worse is that I am going on a month-long trip in a couple of days, so there is no way I can get another one - and by the looks of it, even if I got a replacement, the chances are that it too is a piece of ****#e without a functional speakerphone. This I-mate Jam (or whatever the 50 name sit goes by) is just a low quality piece of garbage.
HTC/I-Mate is garbage company. There is no chance in hell I will be buying any future Jam or I-mate phone.
Related
Well, that's weird. My friends new XDA 2 is acting up. He lost his soubd trough speaker couple of days ago, and then it came back. Today it happened again. I have no clue what's going on, hard reset didn't help. Any suggestions?
TIA
Has he been using hands free headset? If its anything like the xda 1 the connecter is very problematic and prone to problems.
Yes, very frequently. Looks like that's it. He connected and disconnected couple of times again and now it works.
Hello everyone...
Well, I'm another victim but in this case my MDA2 is muted but not deaf...
I'll explain... Most people with this problem have said that they can't hear nor can be heard when they have this headphones plug problem (i.e. The plug when inserted got the contacts stuck so the system thinks the plug is still inserted).
But in my case the other party DO hear me (this is without using a headphones) but I can't hear them or the system sounds, music, etc. but when I plug my headphones I can hear all sounds with no problem.
The day it failed it was all of a sudden, no water, no bumps, no nothing... actually I was not even using my headphones, so the jack it's out of the equation...
Any ideas?
Well as a matter of fact, about three weeks ago I dropped my MDA2 to the pavement and it scratched the case a bit, but it was working fine for the last three weeks...
Do you think this may be a retarded symptom of the accident three weeks ago?
I'm starting to think the speaker failed or got unsoldered...
Any ideas?
Thanks!!!
Rayan
hi Rayan
i had the following problem: i couldn't TURN UP the volume.
i could move the volume slider, but when i took another look to see if the device did really set the slider to the volume i had set - nada - zero.
volume was down again.
if you encounter the same problems: make it short and give your device a COLD reboot. that was the only thing that did help and gave me back audio.
regards ize|man
Hi izeman,
Well, I even performed a hard reset to factory defaults and nothing!!!
And because of that I'm sure it's a hardware problem...
I just hope it's a simple fixable hardware problem... I'm just wating to get in touch with the guy's at gsmphonesource.com (I have sent SEVERAL emails and voicemails and no one has contacted me back!) :evil: (nice customer service huh? :? )
Well I'll let you know how this story ends... :roll:
Thanks,
Rayan
WHOOOHOOO!
I fixed the problem!!!
Since the guys where I purchased my MDA2 NEVER returned my calls and emails, I got desperate and fix it myself!!! (I know I void my warranty, but it was useless anyway since those *&^%$ guys refused to take my calls)... :evil:
Anyhow, I carefully opened my MDA2 and got all the way into the speaker (which is actually encased in a module with two small gold plated connectors on the top) and cleaned them both, on the speaker module and the motherboard where two matching springs are located. I even carefully pulled the springs to give them a little more "pressure" when assembled.
Well, what can I say... I'm very happy to have my sound back!!!
If someone want to go this route, please let me tell you that it was a pain in the buttocks just to pry open the casing, but now I know how to do it, so drop me a line if you need any assistance... Maybe I will document the procedure with pictures once I have some spare time!... :wink:
(Now I can get rid of my stupid wired headset... It's amazing how those damn wires get to tangle so much!)
Best regards!
Rayan
Sound problems
Hi Rayan,
Good to know you fixed it - I have exactly the same problem; speaker only works intermittently. :evil:
I'd like to take to up on your offer to provide further details; especially how your opened the case without damaging it. :?:
cheers,
Pete
XDA II, Scandisk 512Mb, Plantronics 3000[/quote]
Rayan's fix...
http://forum.xda-developers.com/viewtopic.php?t=8525&highlight=sound+problem
Hi,
No doubt as many others have, I managed to drop my XDAII one too many times (they are a bit to light and smooth).
I think the speaker is no a bit duff as sometimes it stops working and I can't hear the other person. If I press on the circular bevel on the case that hides the speaker it starts to work, sometimes tapping the bevel also brings the speaker back to life.
I wanted to know, could this be a simple problem like the speaker connection coming loose or something more serious where a solder fix will have to be applied?
I think the device is still under warranty so I might be able to RMA it but I wanted to know how easy or hard is to fix this, can it be fixed by me or should I send it in to be repaired?
Cheers,
Taz
I would send it in for repair, once you break the security seal you will invalidate warranty and then you will be in trouble if another hardware failure occurs. It is probably a simple connection problem.
its just likely to be the spring connectors from the board to the speaker which is fixable (details can be found in the forums HERE).
However, the O2 XDAII has a 24 month warranty which i found out in November as i had exactly the same problem and decided to take it to my local O2 shop to have it repaired. It took them 1 week to get it back to me but they told me my unit was irreparable and gave me a reconditioned unit as a replacement. I was not very happy as the case was scratched all over etc and my unit was as new. I complained and asked them to give me a new unit. After a further 2 weeks and 2 more instances of sending it back to the repair centre i eventually got a brand new fully boxed XDAII (second battery, second case, second cradle etc etc) from the O2 shop but not until i kicked off with the manager stating how unprofessional O2 was in repairing/replacing a unit that was under warranty.
NB. New XDAII screens are no where near as good as the original screens when looking at it from an angle. They look fine straight on but colours fade/change when viewed from below or from the left.
Hope some of that helps.
Cheers mate,
I think I still have about a year on the warranty but I heard that the XDAII are no longer in production so I am a bit worried that I may not be able to get it repaired however a pal reckons they should upgrade me to the XDAIIs (I had one, didn't like it).
I will visit my local O2 shop in a few days and kick it off with the manager as well... to get some results of course
Cheers,
Godz
Hello all!
First, thanks for an awesome forum! It has both helped me tweak my Wizard, and also get help when I have needed it.
Well, I have no choice now but to ask here. Last autumn, my warranty was almost up, and a wierd problem presented itself. The mic and speaker suddenly just stopped working! The sidespeakers still work, I think, because the phone rings when someone calls me. But the caller can't hear me, and I can't hear the caller. And there isn't a hint of sound in it, no static or noise, there simply is nothing.
As there were only a few days before the 2 year warranty was up, I ran to my dealer and turned it in. A few weeks later, the phone returned, working again. But now that I come to think about it, I don't remember if I got a replacement or if they actually repaired it... It looked a little like they handled it rough though, maybe it was another phone... Well, that's not important right now.
The same thing has happened again! Summary:
1. Mic & phonespeaker dead
2. Stereo speakers work under certain conditions
3. Wired headset that came with the phone works, both for calling and media
So it seems like a hardware problem. Please note, although I downgraded the phone to original, official Swedish Qtek 9100 ROM, it has been thoroughly tweaked and upgraded to a number of different WM6 ROMs - but all that has been working beatifully!
Still, what are the odds for the mic&speaker dying twice in a row, on different phones (i think the present one is a replacement)?!?
Question: Does anyone recognize this? Is there a possibility that it is software related, and maybe fixable? I have searched both the web and these forums but haven't really found any information on it.
ANY input would be greatly appreciated!
Additional information:
Qtek 9100 (Swedish), G3 model, WM6 upgrade successful (unlocked)
EDIT: There are no system sounds, which is wierd, because the phone can still ring. I thought the system sounds came from the stereo speakers on the sides of the device?
Hello all!
It is a glorious day to be alive!!! Or to have a fully functional Wizard, at least!
Lol - my topic isn't very old, and i reply to it myself with a solution (?). I Googled after the Wizard service manual, and found it right here on Xda .
In all honesty, i didn't do all that much. I just followed the disassembly instructions of the wizard about half-way through, to the point where you get down to the back of the motherboard. I poked and fiddled enough to locate the mic assembly, only to discover that the mic is soldered to the mainboard of the phone. So, i figured i'd just leave it be, because if the mic is really broken the motherboard needs to be repleaced, or a replacement mic needs to be soldered on there.
After removing A LOT of dust in there (honestly, i think the service center that had my device last time wasn't very careful with anything, even a screw was missing! ), i reassembled it. The flat cable running to the keyboard was also a little skewed, but that may have been me, anyway i corrected it too. Same with the speakers.
Long story short, after successfully reassmbling the phone, i fired it up, called my home phone and voila! I works!
Not much of a fix, as i don't really know what i did exactly, but dust, dirt and some bad connections/soldering may have benn the culprit.
All in all, i'm very pleased with my afternoon here. Thanks for stopping by .
epatnor said:
Hello all!
It is a glorious day to be alive!!! Or to have a fully functional Wizard, at least!
Lol - my topic isn't very old, and i reply to it myself with a solution (?). I Googled after the Wizard service manual, and found it right here on Xda .
In all honesty, i didn't do all that much. I just followed the disassembly instructions of the wizard about half-way through, to the point where you get down to the back of the motherboard. I poked and fiddled enough to locate the mic assembly, only to discover that the mic is soldered to the mainboard of the phone. So, i figured i'd just leave it be, because if the mic is really broken the motherboard needs to be repleaced, or a replacement mic needs to be soldered on there.
After removing A LOT of dust in there (honestly, i think the service center that had my device last time wasn't very careful with anything, even a screw was missing! ), i reassembled it. The flat cable running to the keyboard was also a little skewed, but that may have been me, anyway i corrected it too. Same with the speakers.
Long story short, after successfully reassmbling the phone, i fired it up, called my home phone and voila! I works!
Not much of a fix, as i don't really know what i did exactly, but dust, dirt and some bad connections/soldering may have benn the culprit.
All in all, i'm very pleased with my afternoon here. Thanks for stopping by .
Click to expand...
Click to collapse
hi epatnor,
I think the problem with your phone was a stucked microswitch in the 2,5 mm connector for the headset. I read about it here in the forum. Sometimes the switch stays in the closed position and the phone still thinks the headset is connected. Thats why all the sound is sent to the not connected headset and therefor your phone seems to be not working (unless you connect the headset)...
But removing the dust is for sure not a bad thing...
For the next time: I think there was an easier solution for this problem than disassembling your phone...
regards
huibuh_1
Thanks huibuh_1,
Yes this was probably not the smoothest way of "fixing" it. That said, the stucked microswitch theory would actually fit my problem well - I can see now that the exact problem I was having would arise if such a switch was indeed stuck.
However, I think that the problem would be more intermittent since I actually use that port now and then - especially since it's the only way to talk (besides using a bluetooth headset that is). And since I connect the wired headset now and again the switch is used and moved, I suspect that this would result in the speaker/mic coming online again maybe..? Temporarily at least?
All the same, thanks for replying - this might happen again and with your information I'm better prepared for it!
I really like the Orbit 2, its a great device BUT within weeks of getting mine, the rubber wheel fell off and it went back for a replacement.
It's happened again with my second one and so it's off for replacement again - I'm only a couple of months in to my contract and already I'm getting my third device!
How's it been working out for everyone else who owns an Orbit2? Any major issues? How's everyone feel about the device?
Is anyone fed up enough with it that they are looking to change?...possibly to the Diamond (which I have been considering). I had no issues with my original Orbit which I also loved but if this one keeps playing up then I'm gonna have to look in to canceling my contract and possibly getting a HTC Diamond - has anyone any thoughts on the Diamond as an alternative to the Polaris/orbit2?
Cheers!
Edit: Just realised I've posted this in the 'upgradeing' sub-forum rather than the Polaris forum, apologies for that! maybe a mod could move it if needs be? ta!
The wheel fell off mine too.
Least they replaced it and the new one is going well
I'm hoping this doesnt happen to mine, I'm not on contract with O2 and bought the phone off steelbay. Is there no way you can re-attach it yourself with locktite ?
Nogs
i have O2 OrbitII for more than a month and no problem at all
i bought it from eBay too
nogs - there's a load of other threads about this rubber wheel problem, its quite a big issue but I think others have managed to stick it back on somehow (as long as it hasn't been lost!)
I tried superglueing one of mine and screwed up the rubber!
I'm on my fifth Orbit 2 since April. The rubber wheel fell of three of them and the data connection of the usb socket failed on the fourth.
O2 suggested another handset, but there's nothing really suitable, it's a real shame as the phone is great when it's in one piece.
That's mad! to be fair though, it's cool of O2 to keep sorting it out for you and for and it's reasuring that they offered a different handset. I see what you mean though, there's not much else to choose from at the mo when it comes to O2!
My thrid one has just arrived, so far so good I'll see how it goes. They are great phones aside from these issues.
I'm using my Orbit for over 6 weeks now and I'm very happy with it. Never had any probs with the wheel or anything else and hopefully I wont considering I've voided the warranty by unlocking the phone,installing new radio and new rom on it.
I use my Orbit heavily as an mp3 player and the only minor issue I encountered was with the mini usb connector when I plug in the wired headset or an adapter for headphones. 2 weeks ago one of the earphones on the wired headset even stopped working bc of the connector. (its the headset not the phone) I wish HTC would have integrated a TRS connector..
*And yes I want to change it bc I don't have video acceleration, accelerometer built in and VGA screen but I won't do this until HTC Android is out or if it takes ages until they'll release it I'll go for whatever will be available in spring/summer 2009. So far the device does everything I need and I'm very happy with all the other functions.
I have O2 orbit2 now 3month.. ring is no problem but camera button is too bad..
it makes feel hard to press button.. how about you?
yup, camera button is very hard to press
i thought that there's some dirt underneath, but it's not
it's just hard button ...
luckily i don't use it that often
Thought I'd update this for the hell of it. I'm now on my 4th Polaris - good times!
I'm on my fourth too, gonna be sending this one back aswell!! 3 wheels and a failure! The wheel fell off this one in 4 days!
Think I will superglue it on next time!!
On the upside I did get 3 complete box sets with all the accessories!
biscuitboy said:
On the upside I did get 3 complete box sets with all the accessories!
Click to expand...
Click to collapse
Me to!!!
I've a big pile of accesories and no idea what to do wit them, including 3 spare car kits and a battery I kept.
is it just me or does it seem like only the orbit jas the issue with the ring falling out? does anybody have a touch cruise that the button has fell out off?
I've got an Orbit 2 and it's just started falling apart. First the screen became separated. I think it's the digitizer as it still works, but i can see liquid in between the layers.
Then a week later the rubber ring fell off.
Not sure what to do as I bought it on eBay... Any suggestions?
I love this phone and would like to get it replaced...
Might be worth calling the manufacturer to see if it's still covered by a warranty then if it is you should be able to get it repaired or replaced. Failing that, you may have to cut your losses and put it back on EBay or pay for it to be repaired.
Hello Everyone
I have an Acer S200 and I ended up cracking the digitizer and lost the use of the entire display. Not sure how. It was in my pocket.
I purchased a replacement on ebay and replaced it. The screen works just as new. How ever I seem to have done something to the earpiece and mic.
When making a call, the earpiece is silent and the no one can hear me. However if I turn the speaker phone on I can have a complete 2 way conversation.
I originally thought it was my ROM however I have tried a few and finally placed the official one on, no luck.
I have taken the phone apart and put it back together a couple times, making sure that all peices are tight.
I am at a loss
Any suggestions will be appreciated
Thanks
Solved
I was able to solve this issue. It was prevoiusly posted. I did search however I was entering the wrong perameters. Anyways...
The solution is here...
Was not able to post URL...
You can do a search for "Speaker problem"
Regards
Hi i have to change the digitalizer,is it hard?Do i have to unscrew the back screws?Can you give me a little of instruction?I have a good pratice to disassembly phones,but maybe you can give me some tips
ACsurge said:
Hello Everyone
I have an Acer S200 and I ended up cracking the digitizer and lost the use of the entire display. Not sure how. It was in my pocket.
I purchased a replacement on ebay and replaced it. The screen works just as new. How ever I seem to have done something to the earpiece and mic.
When making a call, the earpiece is silent and the no one can hear me. However if I turn the speaker phone on I can have a complete 2 way conversation.
I originally thought it was my ROM however I have tried a few and finally placed the official one on, no luck.
I have taken the phone apart and put it back together a couple times, making sure that all peices are tight.
I am at a loss
Any suggestions will be appreciated
Thanks
Click to expand...
Click to collapse
i got my s200's screen leaked by itself without no pound by anythingelse.
in hong kong there's a nickname of acer's phone - the king of cracked mon.
the agent had my phone's mon changed twice, and i really worry the coming of the third becasue the agent will charge me.