Does one of these exist? I have a cheap TPU S-line case from ebay that I bought when the phone was first released. It works with the QI charger but it does not keep the dust out of the ports.
I bought two cheapies off ebay to test if something a little thicker would work with the QI charger and so far nothing does. Seems that any case that covers ports are thick and may not work with the QI charger.
BTW its the Energizer charger, not the official Google one.
Have you considered just getting a microusb port cover? http://www.moddiy.com/products/modDIY-Micro%2dUSB-Protective-Jack-Cover.html for example
ziddey said:
Have you considered just getting a microusb port cover? http://www.moddiy.com/products/modDIY-Micro%2dUSB-Protective-Jack-Cover.html for example
Click to expand...
Click to collapse
I have but if a case exists that will work then I would like to give that a shot first. I notice the covers for the cases are snug fit so it wont allow dust in at all when a plug may leave room between it and the case. I work in a very dirty environment and would like to keep the phone itself as clean as possible.
Whilst viewing YouTube custom case reviews for Note 4 I've noticed some people using a thin metal disk sandwiched between their phone & the case with no explanation. What is the purpose? Does have something to do with nfc.
It's probably a Qi wireless charging receiver. Some folks extract the coil to reduce the thickness of the receiver.
I use a magnetic car mount that has a thin metal disk so it sticks to the holder.
The case I use has a magnet in it for my car mount. Will that interfere with wireless charger?
geekdadof3 said:
The case I use has a magnet in it for my car mount. Will that interfere with wireless charger?
Click to expand...
Click to collapse
Try mounting your phone without the plate in the case. I used a slim case on my Note 5 and now Note 7 and they stick to my dash mount fine. The coils in the phone are enough to stick to a strong magnet.
I've had much success with the phone sticking to my magnetic mount without any case.
I'm considering buying a magnetic car mount for my G6 because I'm lazy and don't want to have to fit my phone into the mount I currently have, but wondered about NFC.
I've got a thin Spigen case on my vG6 (dropped it, smashed the rear glass, had it fixed, don't want to repeat that again!) so I can place the magnet on the case rather than the phone, but if I do will this block or prevent Android Pay payments while the phone is in the case? Do these magnetic mounts for that?
Anyone tried one or tips on where to place the magnet to stop this happening?
Thanks
I tried and with the magnet in the back the phone does not do wireless charging so other features might not work depending on where you stick the metal plate.
Sent from my LG-H872 using Tapatalk
FCORivers said:
I tried and with the magnet in the back the phone does not do wireless charging so other features might not work depending on where you stick the metal plate.
Sent from my LG-H872 using Tapatalk
Click to expand...
Click to collapse
No wireless charging on mine anyway. I have the European 870 model
Wondering about the same thing. I've ordered a case with metal strip for magnetic holder, but will NFC still work?
I am using this one, NFC works just fine.
You can google or ebay 'Baseus Universal 360° Finger Ring Stand Phone Holder'
joezhao said:
I am using this one, NFC works just fine.
You can google or ebay 'Baseus Universal 360° Finger Ring Stand Phone Holder'
Click to expand...
Click to collapse
Cheers mate.
That's gives me hope that any of the others should work fine too
Never got into wireless charging on my S7. Always had a magnetic mount on the vent with a metal plate between the phone and the case. Now that I'm hooked on wireless charging, I'm on a similar setup but with a wide ring magnet between phone and case so it doesn't interfere with wireless charging. My one issue is that when the phone is flat on a desk, it rocks just a little (and I like a thin case). So what I'm looking for is a thin case, with an embedded magnet (so it's a flat bottom surface) and where the magnet is in a configuration where it doesn't interfere with wireless charging (whether it's a wide ring, or a few magnet points spaced out, etc.) I've thought about digging into my case as a DIY but not there yet Pitaka MagCase looks like it would so the trick but it hasn't been released yet. Any out there that I'm just not finding?
Thanks!
And, this is on an S9 plus.
Can you post pics of your setup? I'm looking for a magnetic wireless car charger that holds up via the vent.
Sent from my SM-G965U using Tapatalk
thx for the tip.... now i want one too
https://www.ipitaka.com/collections/magcase-for-samsung-galaxy-s9
Search on Amazon for "Magnetic Wireless Car Charger, ELEGIANT Fast Wireless Charging Car Mount Phone Holder". Looks like it's now out of stock but there's dozens just like them. I went with something inexpensive to make sure it worked. And it did- fast charged on the mount as well as the Samsung official desktop wireless charger. Although the swivel ball joint on the vent mount was a little flimsy. I placed the magnetic ring such that the top of it was about 1/4" below the bottom of the fingerprint sensor (I spent a lot of time trying to figure out exactly where the coils in the phone were; you can take a good guess by knowing that the desktop Sammy wireless charger woks with both the phone standing upright as well as on it's side and that it's got two coils).
Even though the ring is very thin, it still adds a slight bulge in the middle and makes it "wobble" a bit. I don't have the right shop equipment to shave a circular channel on the inside of the case to place the magnetic ring
Found one made by Nillkin. Have to use their own charging mount (which makes perfect sense as it uses four small magnets at four corners of the mount). Reviews aren't great, it's standard (not fast) charging, and the I like my side buttons uncovered.
Xvida makes one as well (a little bulkier than the Pitaka) but S8 is the most recent they support as of now.
hey guys,
you might wanna hold off getting the pitaka magmount, I received info from pitaka that the s9+ position of the wireless charging coil of S9 therefore the position of the built-in metal plate is different from other cases, they are still testing there new wireless charging mount, it will come out later.
I will be getting a review unit of the case later and I will let you know how I feel about the case. cheers guys.
xzr3b0rnzx said:
hey guys,
you might wanna hold off getting the pitaka magmount, I received info from pitaka that the s9+ position of the wireless charging coil of S9 therefore the position of the built-in metal plate is different from other cases, they are still testing there new wireless charging mount, it will come out later.
I will be getting a review unit of the case later and I will let you know how I feel about the case. cheers guys.
Click to expand...
Click to collapse
I have the iOttie magnetic mount/quick charger in my car.
It worked really well with my S8 and note 8.
I put the small metal ring inside the case on my S9+ and it was very finicky.
Sometimes it would only charge (not fast charge) and other times it wouldn't charge at all.
I found that by placing the ring up higher near the camera, it maintained position to quick charge the phone and hold it securely.
The qi coil in the S9+ seems to be a bit closer to the camera than the other devices I've used.
I hope this helps.
Sent from my SM-G965U using Tapatalk
Great- thanks- similar to my current setup- I'm just looking for a case where the ring is actually embedded in the case, so the back of the case is perfectly flat.
Looks like from another thread the S9+ MagCase has launched- not on Amazon yet but on the Pitaka site- would love to see a review to make sure it quick charges wirelessly (as opposed to not quick). Sounds like they had issues with magnet placement originally and that might affect it.
Nillkin makes one. It's on Amazon as well.
y2k1ltd said:
Nillkin makes one. It's on Amazon as well.
Click to expand...
Click to collapse
Yes- thank you- the Nillkin looks great- and a lot less expensive than the Pitaka- but the case has full edges that cover the buttons which I'm not a fan of.
texasmax said:
Yes- thank you- the Nillkin looks great- and a lot less expensive than the Pitaka- but the case has full edges that cover the buttons which I'm not a fan of.
Click to expand...
Click to collapse
Gotcha, it's not bad.