I've had my NST Glowlight for roughly a year (so the warranty's run out). I haven't used it since October or so, and when I tried to charge and boot it recently, it doesn't do anything. When I plug it in, the green LED immediately turns on, and if I wiggle the charging cable a bit, it'll turn to amber, but no matter what I do, the thing won't turn on. However, the backlight will work (for as long as it's plugged in; the backlight will turn back off after about 30 seconds if I unplug it). I've taken off the back panel to have a look at the battery. It seems fine: the positive and negative terminals read ~4.10V, and like I said, the backlight works. I've also tried all of the standard reset things such as holding the power button for 20-30 seconds, holding both the power and the N button for 20-30 seconds, leaving the battery unplugged for a while then trying to charge it, trying to charge it for a long period of time (about 6-8 hours).
In any case, nothing I've tried has worked, and I'm starting to get frustrated. The other two times this has happened, I could just return it and get a new one, but now that that warranty's gone, I'd have to buy a new one, which I'm not really all that willing to do.
If anyone has any ideas or insight, I'd be very grateful. Thank you in advance.
A voltmeter on the battery with no load might be a red herring.
A 100 ohm to 1K should be enough of a load.
A Nook without a battery will refuse to boot, however it will pop up in bootloader mode for a bit.
If you just plug in a USB cable does it popup on your PC "New device found"?
This thread might be of interest: http://forum.xda-developers.com/showthread.php?t=2559915
You can probably skip to the end.
Related
Hi everyone, yesterday I took my G1 from my pocket (after using it normally for some hours) and it was turned off. I thought the battery was dead (I left it at about 20% charge) so I tried to turn it back on and surprise...no vital signs at all. The phone didn't turn on, and the led was dead. After losing half of my hair, I tried removing the battery and placing it back. Now the phone behaves like this; when I press the power button, as long as I keep it pressed the led flashes red and that's it. When I stop pressing the power button the led stops flashing. When I plug the usb cable, the led gives a solid red and stays like that forever.
Please someone tell me it's just a screwed up battery...please
Neuromansa said:
Hi everyone, yesterday I took my G1 from my pocket (after using it normally for some hours) and it was turned off. I thought the battery was dead (I left it at about 20% charge) so I tried to turn it back on and surprise...no vital signs at all. The phone didn't turn on, and the led was dead. After losing half of my hair, I tried removing the battery and placing it back. Now the phone behaves like this; when I press the power button, as long as I keep it pressed the led flashes red and that's it. When I stop pressing the power button the led stops flashing. When I plug the usb cable, the led gives a solid red and stays like that forever.
Please someone tell me it's just a screwed up battery...please
Click to expand...
Click to collapse
Probably bad battery. It is certainly worth it to at least try another battery -- they're dirt cheap anyways, or better yet, BORROW one.
* Solid green (when connected to the power adapter): The battery is fully charged.
* Solid red (when connected to the power adapter): The battery is charging.
* Flashing red: The battery is low and needs to be charged.
* Flashing green: There is a new notification.
Neuromansa said:
Hi everyone, yesterday I took my G1 from my pocket (after using it normally for some hours) and it was turned off. I thought the battery was dead (I left it at about 20% charge) so I tried to turn it back on and surprise...no vital signs at all. The phone didn't turn on, and the led was dead. After losing half of my hair, I tried removing the battery and placing it back. Now the phone behaves like this; when I press the power button, as long as I keep it pressed the led flashes red and that's it. When I stop pressing the power button the led stops flashing. When I plug the usb cable, the led gives a solid red and stays like that forever.
Please someone tell me it's just a screwed up battery...please
Click to expand...
Click to collapse
Leave it to charge for 30 minutes or so, then try to power on. should be okay
better to charge from ac power if u can
Its possible your charger could be faulty.
I have the same problem, has anyone found a solution?
Try leaving it charge for a good hour, or just go out and try a new battery, could just be dead.
Sent from my Xoom
sometimes if a battery gets to low it wont even charge... not just for phones but cameras too and so on..... iv had to do this to cell phones and cameras.... take a usb cord you dont care about and cut it and expose the red and black wires..... look for the positive on your battery and negative, usually its marked, how positive to positive and negative to negative for 30 seconds to a minute while its plugged into the computer then, pop the battery back into the phone and try to charge..... everytime iv had to do this for a freind or something of my own the battery has lasted over a year after with no problems.... just a suggestion
Thanks for the suggestions. I had already ordered a new battery and the phone boots up with it but it won't charge on or off and usb isn't recognized either. I tried wiggling the plug around to see if it was some kind of loose connection but it doesn't appear to be the case. I may take the phone apart and see if anything is loose but otherwise I'll just have to enjoy the last 30% battery of G1 time I have.
Hi booard,
I've a problem with my STR. I let it untouched for a little while (like 2 weeks) and I guess the battery emptied, as I was unable to wake it up.
I've plugged it the whole day but there is still no sign of life. I pressed the power button for 30s (which I think should be the reset to factory button) but still no luck.
Any advice? (As I live in France brigging it back to the store is not an option )
Thx in advance!
Anyone?
First sign of life : the charging LED switches from green to orange and now seems more on the orange side.
Maybe a bad electrical contact?
Ok. I encountered a similar problem, which I think was a result of me running too many apps simultaneously in the background draining too much of my battery. I tried different methods of turning it back on but unsuccessfully. I was playing around with. I tried plugging and unplugging the USB cable hooked to the computer USB port at various times, while trying to turn the device on. One time the led light would only stay green. Other time the screen changed color to some kind of weird shade of gray. I was charging it for over 3 hours without any luck of turning it back on.
Eventually I got an idea where I used the fact that the electric plugs in my country are 230V instead of 110V typical for the US. The whole idea was hooking my nook up to this extra power without using reduction, knowing the risk of burning the nook of course. So I was charging it for like 30 minutes plugged to 230V, it was still telling me to wait for it to boot up on it's own after 15 minutes, however I tried to turn it on again and voila the damn thing booted up.
I went out for a while with my battery at 20%, when I came back it had drained out. I put it to charge, but when I tried to switch it back on, it refused to boot. On a normal power button press, it would vibrate 3 times and then the red notification light would start blinking. Same thing with power + volume_up. If I press power + volume_down, it would vibrate 5 times and the green notification light would stay lit. Nothing comes on the screen, whatsoever.
I was rooted with S=off, and was using the Operation Inferno ROM (which I have been using comfortably for the past month or so).
I did try some stuff with ADB, such as using it to reboot into bootloader and recovery (same 3 vibrate + red notification light), pushed the Operation Inferno ROM again to the sdcard and tried to restore the ROM from that location (for which I got adb: unable to open file /sdcard/backup.zip).
I haven't yet gotten around to downloading and installing the factory image some have suggested for the eMMC issue (PD15IMG.ZIP) but I wanted additional opinions considering most people with an eMMC issue have been able to open HBOOT at least.
When the phone doesn't power on, neither ADB nor fastboot will help you. There is no device on the other side, so all your attempts went to the drain, and it was expected. Nothing to do with eMMC issue or anything else. Your phone just doesn't power on.
Put your phone to charge, if the light turns orange - just leave it to charge until it's green, then disconnect and try to power on.
If the light doesn't turn orange, or it doesn't power on even after charging - remove the battery for 10 min, press Power button for 1/2 min, release the button, reinsert the battery, put to charge. And again, let it charge before you try to turn it on.
I did charge it earlier (for about half an hour or so) and the orange light does come, but it didn't boot after that either.
I'll just give it a try by charging it through the night and see.
I think a key thing is to take out your battery for 10 min, as Jack_R1 suggested. Then proceed with the charging.
Sent from my HTC Glacier
Still doesn't work. I dissembled it and kept it like that for quite some time, then put everything back and charged it for hours. Still the same issue happening during boot.
Connect the phone to USB, powered off, see if the PC recognizes "QHSUSB_DLOAD" device. Try to power it on, see if it happens.
If it happens - it means your primary bootloader is screwed, in another words - no repair (actually, repair is theoretically possible, but no guide, no information and no sources exist for MT4G).
Jack_R1 said:
Connect the phone to USB, powered off, see if the PC recognizes "QHSUSB_DLOAD" device. Try to power it on, see if it happens.
If it happens - it means your primary bootloader is screwed, in another words - no repair (actually, repair is theoretically possible, but no guide, no information and no sources exist for MT4G).
Click to expand...
Click to collapse
When its plugged in, its recognised by the ADB (even when powered off), and I can do some basic commands (mentioned in the first post). When I power it on the same thing happens as when it wasn't plugged into USB (ie, the vibration and the blinking LED).
I'm also worried about water damage, since a very tiny amount did come on it as I was sweating profusely. Although the indicators in the battery tray and on the battery itself don't signal damage (they're completely white) I've just decided to try and keep it opened up in a bowl of rice, just in case, until someone is able to come out with some idea.
As I'm in India, taking it to T-Mobile is not an option. If nothing works out, I might take it to HTC and see if they can help out.
I think I have fried my Nexus 7.... didn't even think about what I did how stupid am I....
I decided to wire up a Hella connector to a USB cable the idea being to plug it into my phone for charging on the road... I then had a not so smart idea to use my OTG cable to connect the USB A connector to my Nexus 7 to see if it worked...
Nexus 7 booted past the bootloader and then nothing.... I realised then how stupid I had just been...and still nothing...
Presumably I've run a shed load of power down one of the data line..... what a fool.....
ARGH!!!!!!! anything I can possibly do to salvage it.... please!! :crying::crying::crying:
you could try something ASUS support told me, press all buttons (volume + & -, power) for 30 seconds, and if it won't boot after that, you should get a RMA
chiwou said:
you could try something ASUS support told me, press all buttons (volume + & -, power) for 30 seconds, and if it won't boot after that, you should get a RMA
Click to expand...
Click to collapse
Going the RMA route would be costly. If it is dead, he'd be better off just bring a new N7.
Sent from my Nexus 7 using Tapatalk HD
Thanks for the suggestion but no it hasn't worked...
I've had the N7 plugged into the charger for the last 30 minutes or so and when I went back to it the screen backlight was on slightly (you can see if you look at the screen from the side)... but the whole unit was really really hot... I've obviously disconnected it but now can't get the thing to turn off, if I hold down the power button the screen flicks off but then back on.
:crying::crying::crying::crying:
najaboy said:
Going the RMA route would be costly. If it is dead, he'd be better off just bring a new N7.
Click to expand...
Click to collapse
I would think that "broken displayā€¯ units on eBay/CL probably have working mobos and batteries, as the owners are trying to dump them because of the broken screen. But, buying used is a crap shoot.
Nice that Google is selling N7s at cost (or even a loss) - but it does mean that any oem component replacements will be a significant fraction of the original price.
I was reading in Play Books when my N7 shut down due to low battery. I plugged it in and it wouldn't charge or boot and I noticed a faint light bleed and faint dots streaming from right to left on the display. I tried things like holding the power button for 30 seconds to reset, holding vol down and power to try to get to recovery, but it wouldn't take. Finally, with it plugged in, I held down the power button for just about 10 seconds and backlight and dots stopped. A few seconds later without pressing anything, it booted up. It would start to charge, but if the screen timed out, I was back to the earlier state and it wouldn't come on. So I got it started again and immediately went to developer options and checked Stay Awake while plugged in. Eventually the charge built up and I'm back to normal, at least my N7 is normal. I only mention this because the OP talked about the faint backlight and it may be worth trying.
busterdan said:
Thanks for the suggestion but no it hasn't worked...
I've had the N7 plugged into the charger for the last 30 minutes or so and when I went back to it the screen backlight was on slightly (you can see if you look at the screen from the side)... but the whole unit was really really hot... I've obviously disconnected it but now can't get the thing to turn off, if I hold down the power button the screen flicks off but then back on.
:crying::crying::crying::crying:
Click to expand...
Click to collapse
A standard hella charger outputs 5V at 2A which is the same as your N7 original wall charger.
I doubt your problem came from the charger, it might be softbrick at an unfortunately moment.
I came across a similar problem when i was editing a custom kernel.
If you tried every method to shut down the device and failed do the following:
1. Open the case (it's quite easy to open with a plastic card)
http://www.ifixit.com/Guide/Installing+Nexus+7+Battery/9895/1
2. Unplug the battery and hold the power button 30 seconds (with the battery detached)
3. Let it soak for 10 minutes
4. Reconnect the battery and close the lid.
5. Put your nexus 7 in the wall charger, and you should see the battery bar on the screen.
After that, let it charge a few minutes and boot the device.
So this is what happened:
the phone discharged fully and i connected it to charge. then i got a flashing red led. seeing this as a bad omen i tried to turn my device on - no luck - it wasn't responding.
i unplugged the charger and plugged it back in and again the same result, then again..... and i got a solid red light. so after a few times of messing about with it , trying out a few sources of power and such i got it charging (the battery logo appeared). The charging lasted for ~30 sec and it went black.
So after that the n4 is completely unresponsive. No flashing leds no backlight on screen, NOTHING.i tried out a few chargers and cables and beside those i used a genuine n4 charger (it's 100% working - i tried to charge another device). i left it there for the whole day to charge thinking that maaaaaby the battery ran to a complete 0 and i just need to give it time, as you probably guessed it, that did nothing.
In fact, i think the phone is not charging at all. The reason i think so is because the wall charger is emitting a faint high-pitch squeal regardless of the fact that the phone is connected (it should be squealing only when it's plugged into socket and the phone is not plugged in it)
so TL DR:
n4 is completely dead, no signs of life. The things that were tried:
a handful of chargers and cables that are 100% working on other devices
trying to boot with a combination of volume buttons pressed
holding the power button for 60 sec. while plugged in
prolonged charging (~7 hours)
verbal threatening to sell the damned thing if it's a serious problem
so that's that. i should get my tools back from a friend on monday. i'll try to take it apart, maby there's a loose connector here or there or something. Any ideas what i could try before that?
Some searching around the forums wouldn't hurt. Try this for example.
kalopop said:
Some searching around the forums wouldn't hurt. Try this for example.
Click to expand...
Click to collapse
thanks for the link, that seems to be worth a shot.... i'll be able to take the phone apart on monday, that's the earliest i will be able to try it. i was wondering if there is anything i can do until then to remedy the situation. I mean i'm really getting a kick out of my old sony erricson k300 but i kinda prefer the nexus and would prefer to fix it asap.
ok i fixed it
i used a 3v source and held the contacts manually for 5 min. that returned it to the red blinking led state and after leaving it to charge for 5 min it returned to the battery icon on screen. thanks for the info again.