Hi all!
I started again a new thread where i write down my findings in the MR2 release of the X2. It's originally on the Esato-forums, so i just put the link over here:
http://www.esato.com/board/viewtopic.php?topic=196737
Nice THKS.
7. When hanging up a phonecall, the phone makes three loud beeps via the rear speaker. WHY???
same here... but only if the person u talk to hangs up first. its so annoying.
Lerka said:
7. When hanging up a phonecall, the phone makes three loud beeps via the rear speaker. WHY???
same here... but only if the person u talk to hangs up first. its so annoying.
Click to expand...
Click to collapse
YEp, and having the phone on silent does not make things better either...
Fix
i used registry editor and changed the value of calldrop from p(play) to none.
Rene,
when you hear 3 tones after call finish - is bluetooth activated in this moment for your x2? For example, do you use BT connection to your X2 in your car (handsfree)? Do you think that there is some special requirements for BT headset using to generate this sound on main unit if call was finished?
when you see bad power consumption results - is wifi activated in communication manager in your X2? I think that if you activate wifi - it can be reason for huge additional current if unit can't find appropriate wifi network for some reason.
For example, I found that if I activate wifi - I always should connect unit to charger every day. Then I found that this is specific issue only for me. The specific way of my wifi using is followed - I use 2 different wifi connections to my X2 (on home - secured network through router and in office - open wifi network). I do have connection issues every morning in office and every evening in home. Even if my X2 reports that it's connected to office network - I can see in status bar in Today screen that it's trying to conect again and again - and also I can't use browser or Goggle maps because no data connection is available through wifi. After I power off/on my unit - it can really connect to office wifi network and I can use browser and receive mails e t.c. When I return to home, I see that unit still be connected to office network - but it's impossile. And again - I can't use browser or receive mails by using my X2. After I power off/on unit - it can connect to home network. I can't fix issues in office and in home just turn off/on wifi in communication manager - issue still be actual after this. So, what I do every day - I turn off/turn on my unit every morning after arrive to office and again power on/ power off unit every evening when arrive home So I should spent 2 minutes every morning and 2 minutes every evening to reboot unit. On other hands I think that this is step to avoid more serious issues after couple of days of Windows using - you know usially you can see performance degradation after 1 week of using of any WinMob device - looks like this is result of lot of memory leaks, memory corruptions inside MSFT SW.
if we are talking about unexpected password issue or issue when you can't unlock unit by LOCK icon sliding left or right after press on power on button - for me it looks like memory is corrupted in MSFT lock app. As result some password is requested even if user never activates this password for lock screen. But it's clear that in reality, unit doesn't story in memory any password to compare with entered one - otherwise after power off/on sequency unit still ask password from you. But as I see in the same situation with my X2 - after I remove/insert battery and power on unit - I never see again this issue just after unit goes to Idle.
I think that memory, which is used by MSFT Lock code, can be corrupted only in scope of the same Windows process (of cause if memory is isolated for all processes in WinMob - I hope it's true) - so only other MSFT code can corrupt this memory. Do you know about any public forum where we can ask help from MSFT to see in this issue? I never see that Aaron wrote anything about any contacts in MSFT - but I think that MSFT should be also responsible for any product if Windows logo is applyed to device with WinMob?
To reduce the probability of this issue I never use AutoLock and always lock unit by click on Lock icon in Today panel or by long press on right HW kwy (with key sign).
darkbuster5 said:
i used registry editor and changed the value of calldrop from p(play) to none.
Click to expand...
Click to collapse
IT WORKED!!!
thank youuu
wifi
Hi! I have a similar issue with the wifi that PanichUS described.
The phone sees the network, tells that it's available, but I am not able to connect to it (so I can not do internet browsing, read the emails, etc.)
This happened to me while switching from one network to another, which were in two different places (and the phone was showing the network still available of the place I have already left). But in my case rebooting the phone did not help.
This is not the only case. The same thing also happens to me after I use bluetooth. The phone is connected to the wifi network (I could do internet browsing, etc.), I use bluetooth, and after that I can no more recover the connection. Again it shows that the network is available, but I can not connect to it.
The only thing which helped by now was restarting my house router.
Is the MR2 the last release of the firmware by date? I have bought my phone recently, and for me it seems that it was updated: I have radio, and the theme with grey background (X2 Titan) was activated in the very beginning.
MR2 is last update for X2. Don't wait another update.
Try turn off Wifi in Communication manager before power off and turn on Wifi back in Communication manager after power on.
Wifi
I have discovered that in fact I don't have problem to connect when using an open network, while with the protected one is always an issue.
Reboot of the phone doesn't change anything even if before doing it I switch off wifi in the connections manager and delete all the settings. Nothing - only reset of the router what helps.
I also tried to use other software (Wifi Monster) - the same thing.
The phone is really wonderful, it really has it's spirit with all these panels and generally the interface, but the wifi issue is really annoying!
My advice - don't install Resco Photo manager on X2.
Great app but works very bad on X2.
I instaled older version Resco.Photo.Manager 7.03. This work good.
Wisbaradvance 4.05 is verry unstable,problems and problems.
Related
I dumped my three year old Sony Ericsson P800 for a sleek, chic O2 XDA Atom in March 2006.
It was a dream device and I enjoyed discovering myriad of features as this was my first PPC. My main usage is as a highly used phone (more than 6 hours per day on long conference calls) and PIM applications (calendar, contacts etc). I hardly play games, I only have Scrabble loaded. O2 Plus is my today plugin, I don't use any other. I have a 0.5 GB miniSD card on which I load podcasts or videos, though I watch rarely.
I started facing a number of problems that I haven't been able to solve:
1) If I set up the SETTINGS > SYSTEM > POWER > ADVANCED > ON BATTERY POWER TURN OFF DEVICE IF NOT USED FOR 2 MINUTES; it is supposed to turn off the screen. If a call or SMS comes it is supposed to come alive.
This never worked for me. Invariably the screen would fail to come back alive and I'd need to poke with stylus to Soft-Reset the device. As a result my screen was always on. Expectedly battery life was very very low. This is my biggest grouse.
2) The WiFi stopped working one day in July. It used to work very well and I was using Agile Messenger with my home network for few months. That day, it just crashed as I turned it on WiFi and surfed for sometime. The screen turned kind of white and a mix of colors. I tried a lot of things after that including flashing the May ROM, old ROM and so on. No avail. Nowadays if I turn WiFi on it may work for sometime. I may even be able to connect to O2-Connect or the web. But crash it will. And after that the WiFi option also sometimes disappears from the Wireless Manager. It reappears after a number of reboots. Practically WiFi has become unavailable.
3) Browsing using pass-through with ActiveSync using the Internet connection on laptop never worked for me. Tried many tweaks but never got it working.
4) 2 and 3 above mean I have no working Internet connection on my Atom. I used GSM dial-up networking through my ISP account. But it is so damn expensive. Haven't tried out GPRS yet (no idea how well Airtel's Mobile Office GPRS in Bangalore India will work with Atom).
5) Recently, I have been experiencing silence on my phone during calls where I can't hear the other people talking whereas they can hear me. I tested dialing into same conference with Atom and another Nokia set. On the Nokia there weren't any silences while my Atom had multiple silences of couple of minutes each. This has made my Atom practically useless for the phone function.
I'd be very happy to try out any suggestions that you may have. Before I totally give up on it.
XDA Atom
ROM:20060426B1WWE
RADIO:R060428N_MN1ARC_RS00049
ExtROMEX0018
upgrade to 0822 RadioRom which you can find in the Upgrade part of this Atom forum, and see if there will be any improvement.
Wi-fi Shut-off when we do the first activesync.
I tried closing all programs by going to settings => memory => running programs => close all.
After that I did the soft reset and started the process "Start => Settings => Connections => WiFi Utility => Menu => Turn on WiFi.
Menu => Jump to Network Cards 3. Under Wireless, select your desired network. (If your network is hidden, kindly tap on "Add New")
Enter your network name (if needed), proceed to Network Key.
Select your Authentication, Data Encryption type and your Network key.
Proceed to 802.1x if needed (it is usually disabled)
Tap on Ok, go to Network Adapters => O2 Wi-Fi Wireless Adapter
Configure your IP and Name Server if needed. (If your network allows automatic assign, you might want to exclude this portion)
Tap on Ok, Ok. Proceed to WiFi Status, check if the status is Connected and IP Address is obtained.
Kindly try to use Internet Explorer to surf the internet"
and started the Wi-fi but it would not go on it showed Wi-fi off instead of the routine radio off.
When if went to Wi-fi => about. It showed Driver: Wi-fi not enabled, Firmware Version: Wi-fi not enabled, MAC Address: Wi-fi not enabled.
I tried the hard reset also yet the Wi-fi would not turn on.
So I reinstalled latest version 20060426-mot0822 of the Atom and before I did activesync I ran the Wi-fi and it worked well . After the first Activesync the same problem started.
For Activesync I am using the new version 4.5.0, Build 5059, Beta taken from the Microsoft site where it has the facility to keep on the Allow wireless connection on device when connected to the desktop yet the Wi-fi switches off.
There seems to be a problem with you software and your technical department needs to study it deeply and provide a suitable solution for it
Folks,
I am desperate and I need help - I have had a Cingular 8525 for about a month now. Everything was going fine till Christmas day -
exactly a day after my 30 day return period :-(.
The issue is that every time I turn on Wifi, my device finds countless connections (I live in an apartment complex filled with
young professionals). From here, I go nowhere but downhill. If the phone goes to sleep while the WIFI is turned on, it does not wake up
at all. I do the only one thing that remains to be done and that is reset the phone. This time the device boots up however
the WiFi is still turned on and the phone shows a big exclamation where the bars are supposed to be. Then I get an
error "The Operation failed". Even a clear storage does not solve the issue. If I keep the phone turned off for about a day
and go to a location where there are no Wifi networks, everything is fine again.
I got Cingular to send me a Warranty Exchange device and Lo and Behold, I have the same problems with the second phone
too. I spoke with data device support and they asked me to go to a Cingular store where the device works fine as there are
no WiFi networks there.
I cannot return, cannot use my phone to the fullest extent and am in despair. Can someone tell me if there is any miracle that
I can utilize at this time. Please help !!!
p.s. - I have never installed any third party apps on the phones.
Cannot take time to answer this right now but, the answers are alraedy posted on this board. It does not sound as if there is anyting wrong with the phone except the not waking up part which is a known issue and also documented here. Also try the Wiki http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
I will check in again later
Mike
Mike,
Any help is appreciated. None of the topics below cover issues with WiFi. Once I turn on the WiFi, it will not turn off even with a hard reset or soft reset and then the phone shows the exclamation "!" !!!
Well just for starters I'm going to suggest that you DO add two applications - most importantly Magic Button
http://www.trancreative.com/mb.aspx
With this tool installed you will be able to see from the task bar what programmes are running on your device. (You may or may not know that applications that are opened and then shutdown with the X at top right corner are NOT actually closed but running in the background. Magic Button will allow you to see these and close them down - particularly Active Sync which will get in the way of your WiFi connection.
I think you are not getting any wifi connection but you are detecting networks from folks around you?? Does it detect your own network? and if so at what stage do you have a problem.
If your own network is being detected but the usual means of connecting e.g. by entering WEP key is failing then you might want to install an application called Hitchhiker http://www.kasuei.com/hitchhiker/ this application resolves various conflicts and will re-establish IP address and will allow you to enter the WEP key or even copy and paste it in. Once run and connected hopefully, you can close down Hitchhiker (if you want to) and connect to wifi by your normal route (Hitchhiker will have saved the connection information to the standard locations so you don't need to use Hitchhiker each time you want to connect) (Note you must also download and install the .Net Framework a link for which is also given on the Hitchhiker page given above)
Finally (for now) you say Wifi is on all the time even after soft reset. But you can switch it off, in more than one way. Here's one way, below the on/off switch right hand side is another hard key for the "Communications Manager" . On the screen that comes up you will see an aerial with waves radiating from it. Tapping will close and tapping again will re-open. Here you can also open and close the phone function, though I never close mine.
Mike
1. It disconnects automatically too frequently
2. I have a secure network and I have to enter the 100 digit (seems like) password everytime
3. Sometimes wont' connect at all.
The signal strength is 100% too.
Anybody else have this issue???
Is there a program that can monitor and connect automatically (remembering password) to help me???
Many thanks.
Mine is OK. Only have to enter the password once for the first time. Mine only disconnect when I turn the WiFi off via Communication Manager.
Im with craven.... My WiFi works perfectly.
My WiFi works flawlessly.
There is SPB Wireless for monitoring only.It does not help you reconnect. Good program.
Did you try to adjust the slider on WiFi settings towards Best Performance instead of Best Battery (it's on Power Mode in WiFi settings, from Communications Manager) ?
Maybe you have installed some crappy sofware that takes over your wireless settings(it happend to me when i installed some software- i don't remember it's name right now).
nope mine's ok. doesn't turn unless you specify. Reception is not bad either.
no problem with my xperia...
No problem with Linksys WRT54GL at all. Maybe you should check your router's settings.
Only twice had I needed to re-enter my WPA passkey, but otherwise it's great. Able to enjoy the web whilst in bed and a lot faster than my old P990.
It happened to me twice.
Though no problem lately.
As a little trick, you can use a text file (or whatever code protection software) to store the key and do a copy/paste if you don't want to type the code all over again.
I had this problem at first... I didnt know why it would keep disconnecting...then i figured it out..the wifi disconnects when the phone is in standby. Schaps advanced configuration tool fixed it quick and now im enjoying it very much =)
many people have success upgrading the firmware of their routers to fix
such issues
wifi working grt in my x1
once i entered wep key
now its working grt
You shouldn't use WEP, you can crack WEP under a minute now and even if you use a while "mac" list it's not safe enough since you got the MAC addresses just listening the packets.
my x1 works perfect on wifi. not loosing connection, set up the wlan key at the first time and it was saved forever. have tried it on 5 wlans and everywhere without problems... is think wifi and the gps are the only things that are sophisticated 100% on the x1 ^^
billybobjones said:
I had this problem at first... I didnt know why it would keep disconnecting...then i figured it out..the wifi disconnects when the phone is in standby. Schaps advanced configuration tool fixed it quick and now im enjoying it very much =)
Click to expand...
Click to collapse
It is good only if you have a usb connection or 110/220V nearby as always on wifi drains the battery in a half day
BTW: the wifi reconnect after suspend is really fast here, almost every time 1-2 sec.
mine is just fine, my home wifi uses a 11 digit password, just had to put in once and never again, doesn't disconnect randomly, only when disable the wifi obviously.
you should check with your warranty, see if they can do something about it, cause your case isn't normal.
have you all changed it to best performance in the settings?
im sitting right next to my router...and it loses connection now? this is quite annoying. i put the slider in the middle.. i sometimes leave wifi on when im asleep at home. so i like to keep it in the middle? whats the deal?
haha...about the Xperia wifi problem,just off your bluetooth b4 u try to use the wifi.
i think xperia is sharing wifi and bluetooth in the same device support.
i been test many time....when open bluetooth the wifi is weak and keep disconnect..
if this problem can't slove it then i think u better send to service center to fix it.
I actually found a problem in the Wifi/Wireless configuration.
I have 2 WPA protected routers with long keys/passwords. I found that if I enter the keys for both, the X1 would only remember ONE of them. I tried this by trying to save the password on either one of the WPA routers, and would only remember the FIRST one entered. So if you entered a 2nd one, it would always forget it, and you would need to manually re-enter the password again. Sure, it would connect, but then after it disconnects or you leave the area, then re-enter the area, it already forgot the password again.
i dont have bluetooth on and this is getting pretty annoying..
are you guys all using best performance?
My HTC HD has WIFI Problem: WiFi will not turn on most of the time.
After tapping the Wi-Fi Switch (in Communications Tab) it hangs for about 7 seconds then stops.
Sometimes after 6 seconds the wifi Icon will appear for 1/2 a second but then disappears.
The only way I can get it to connect at all is if the device is cool and I remove the battery for a while....
...Then restart it and Wi-Fi will switch on sometimes (but fail most of the time).
I have flashed the ROM (by different Cookers) many times, Hard Reset the device many times, and used all different power settings: Still no good.
If error reporting is ON I get error message "device.exe' problem.
As I live in Australia I would have to pay heaps for freight if I send it back to UK so I'm loath to do so.
Anybody know what should I do to fix it?
(PS. My old Diamond connects every time)
I have a similar WiFi connectivity problem, but after reading of the poor service provided by most vendors and HTC itself, I will try to gather some more experience with the problem before I contact HTC or my vendor, and hopefully find a solution. Bellow is my experience so far:
I own an HTC Touch HD since January and have a similar problem, only it surfaced last week. Before I had only used the WiFi connectivity briefly. The problems started after I installed an AP on my house expressively for the new PDA. The node is fully open and set to B/G/N protocols.
After a couple days of medium (couple hours per day) use the WiFi connection suddenly quit, the device would try to connect (the top bar showing the WiFi connection animation continuously) and after a few moments gave up with a dialog box stating the current network settings were wrong (even thou they worked fine a few hours earlier).
I tried several hot and cold resets, but only solved the problem after flashing a new ROM; even then the same symptoms reappeared after a couple of days of regular use. Again no re-setting would cure the problem, and now not even flashing the ROM again would work. Nonetheless, some hours latter the WiFi would connect perfectly with the same nodes it refused to before, and in very short time.
I have witnessed this cycle twice and have yet not been able to find a trigger for it, but will keep my eyes open for any tell tale signs, and post any findings here.
What I found out is that If you are using CommManager in TF3D together with other wifi mgr it screws up the wifi. Either you use CommManager or you use 3rd party one but not both at the same time.
Agreed!
Yes I agree completely; something on the permanent storage area got corrupted last week after I installed WiFi Monster (which I like, and recommend, only not at the same time as the standard connection manager).
I managed to get the WiFi conection working again (if only for a couple of days...) by doing the Start>Settings>Clear Storage thing and following the re-install.
Ok, so at least now I know of one more thing that can screw up th HD's WiFi besides itself!
i cant connect to my wifi in my same bedroom !!!
Enhancing WiFi performance
If you get very low range, or frequent connection interruptions, it might help to go to: Settings>Connections>Wi-Fi>Advanced>Power Mode and set it to "Best Performance"
PS. I wonder if anybody gets intermittent WiFi problems like myself. One day it works perfectly, the next it will not connect showing a dialog box: "Warning Cannot connect to the network. Check your network and service provider settings and try again"
hi
Im running the stock JK6 and rooted.
when Im running e.g. the liveview app my phone keeps some kind of freezing after a few minutes, first I tought it is app related but now I revieved my OBD2 scanner for my car and its just the same with the app "torque".
is this a hardware related problem or something wrong with this ROM.
did a HR several times and reflashed the ROM.
Edit: I noticed when bluetooth recieve or send data I cant get any other wireless date like on wifi or on radio.
please help
Seems to be a one time event with the data problem but the main thing keeps annoing me
Have you tried pulling the battery waiting 60 seconds placing the battery back in the phone and then rebooting?
Eh no cause on the galaxy tab the battery cant be removed
NightFire123 said:
hi
Im running the stock JK6 and rooted.
when Im running e.g. the liveview app my phone keeps some kind of freezing after a few minutes, first I tought it is app related but now I revieved my OBD2 scanner for my car and its just the same with the app "torque".
is this a hardware related problem or something wrong with this ROM.
did a HR several times and reflashed the ROM.
Edit: I noticed when bluetooth recieve or send data I cant get any other wireless date like on wifi or on radio.
please help
thanks
Click to expand...
Click to collapse
I don't Know, but if you have a Bluetooth PAN connection to the internet, then it should be not possible to have another connection to the internet. IP routing to the gateway would be confused if you could.
There are tools that "group" several separate internet connections into one virtual one.
no Im not using a bt PAN to connect the inet, only normal bluetooth data usage
Push
Just only me who is facing this annoing problem?
Same problem with OBD2 :s disable GPS reduc freeze loop. But not fully (30 minutes). Next time i will turn off Data conection.
Every time i've freeze now i see torque try reconnect to OBD2, seem like BT of SGT turned off or time out
I am having the same problem. As long as I have bluetooth turned on, it will hang the Tab within 30 min. All bluetooth connections are definitely gone. Turning off the bluetooth won't help. The only way is to reboot and never turn bluetooth on.
BTW, I have tried connecting LiveView or a normal bluetooth headset. Both cause the same problem.
I am on JK2.
It seems it is bluetooth driver conflicting with any other data connections.
Did a further testing. Disabled Wifi, but doing data communication via 3G network while turning bluetooth on. The tab hangs in a few minutes. Found a process called 'btld' sucking up all the CPU circle.
Any ideas what 'btld' is?
Thought this should not be a hardware problem because bluetooth works fine when all data connections are off and Wifi/3G data works fine when bluetooth is off. It must be some sort of default setting isn't correct. If this is the case, then root would be a must before manually tuning any parameters.
Found root cause. It is actually the SonyEricsson LiveView software causing troubles. After removing, everything goes well.
Checked on SonyEricsson's web site, it seems Froyo is yet to be supported.
try to use WO Webcam B-Lite out of market, you can open a bt connection by pressing activate and then while running, close via taskmanager, voila the freeze begun
I've got galaxy Tab and galaxy S, and torque badly freezes the devices almost every time I exit the application. It cannot be an hardware fault since I use lot of bluetooth devices and always 3g connected, never had issues. Just with torque, and I don't have any "sony liveview" thing.
Reading on the comments of Torque it seems that also other devices have the same freeze issue (especially a phone called "Evo 4G"). Many months ago I sent a mail to the developer explaining the bug but he bumped me away replying that the app is tested and working on GalaxyTab (and obviously it's not true, or he did some mistake in testing). Now lots of people with this Evo 4G are complaining and the developer is trying to fix. let's hope..