ok here's the quick: let sprint custs run (i know). relocked and reflashed original verizon ROM dump. manually replaced epst settings and DMU reset. everything works now cept EVDO because:
my HDR AN AUTH User ID: is [email protected]!!! (wow those custos really f you in the end)
when i go to edit it says "write "HDR AN AUTH User ID" error"
I know no EVDO because of failed auth is a common problem, but i think my problem is a bit unique in that i know it needs to be my#@vzw3g.com, but it just wont let me change it. any ideas???
are you not allowed to edit your own auth? can verizon (called 3 times, all morons)? what about qpst or qxdm or whatever?
thanks ahead of time,
-karl
**bump**
anyone?
You can use EPST to change your HRD ID etc.
You will need to know what your MSL code is though.
If you just use the view option of EPST it will not show you the security settings.
If you look at this thread http://forum.ppcgeeks.com/showthread.php?t=25226
It has all the info you need to find out your MSL code etc. I am sure that info is elsewhere on this site to. That is just the place I found it all.
Cheers
my msl is 000000 i can get into edit the settings in epst, it just gives me an error when i try to change my hdr an auth! its so weird!
when i access my settings in qpst i get a write error when i try to change it!
i dont get what gives! hellppp!!
:/
-karl
robstak said:
my msl is 000000 i can get into edit the settings in epst, it just gives me an error when i try to change my hdr an auth! its so weird!
when i access my settings in qpst i get a write error when i try to change it!
i dont get what gives! hellppp!!
:/
-karl
Click to expand...
Click to collapse
ok robstak i had the same problem. If you have QPST 2.7 build215 you would be able to make that work. All you have to do is connect the phone by ##3424# or ##3424 send to put it in diagostic mode. Run QPST be sure its connected then open service programming. after clicking read it will then ask you to input your MSL code. It will only take you about less than 2 seconds to read you phone. once it does go to PPP Config tab then click on UM/AN buttons on the lft side. You will then see a red mesh on the USerId. Click on the red mesh and click ctrl D and it will enable you to change that parameter then write to phone. Viola now it works. Hope this will help you
Related
I know my spc- Cricket has my esn- my min = mdn = msid... I have a Cricket prl, but at *228 I get a PSC failure message, a one minute freeze and soft reset.
I cannot find how to intentionally change one's spc/msl- is it possible?
Look around their is a solution already posted...
On top of that if you do not want to reset you're MSL to 000000 and you know it. Just manually program the phone. You do not need to OTA the phone if you have you're MSL, MIN (MSID) and MDN.
amoamare said:
Look around their is a solution already posted...
On top of that if you do not want to reset you're MSL to 000000 and you know it. Just manually program the phone. You do not need to OTA the phone if you have you're MSL, MIN (MSID) and MDN.
Click to expand...
Click to collapse
I've seen your cricket rom for the 6800 on Hofo- but, before I get into booting roms, I would like to just have a functional phone for the weekend Or maybe a week...
I've already used my psc to update the prl, and edit the mdn, etc... I've used the 1040, and 1041 prls, and still have the psc error at *228...
_______________________________________
Update
using drivers from here I was able to get diag working. Found the com port the phone was in via pc's device manager (was 16), updated that com in qpst (clicking on the qpst globe and adding that port), opened qpst's service programming, then just entered my msl, clicked read from phone, loaded the phone's info, rewrote the msl to 000000 and clicked write to phone- unhooked, *228, viola' no psc error... no more
I get cricket with *228, but that's the only call that's going out on the phone...
I would rather just get the phone recognized by qpst and use service programming(?) to edit the msl- just not sure how to do that yet. I've read others having to use a 6700 driver to get their 6800 recognized- will I need to disable active sync as well?
ug
Thanks- This is stressful
I would love to lock this phone into 3G-only mode like I had with my Vibrant. I tried entering the code *#*#197328640#*#* as I did on the OS 2.1 Vibrant, and it didn't work. The *#*#4636#*#* does however show the mode and allow for the change there, but if I remember correctly, it resets to default after reboot.
I'm not surprised, as surely many things have changed since then. Does anyone know what we can enter on the NS?
allen099 said:
I would love to lock this phone into 3G-only mode like I had with my Vibrant. I tried entering the code *#*#197328640#*#* as I did on the OS 2.1 Vibrant, and it didn't work. The *#*#4636#*#* does however show the mode and allow for the change there, but if I remember correctly, it resets to default after reboot.
I'm not surprised, as surely many things have changed since then. Does anyone know what we can enter on the NS?
Click to expand...
Click to collapse
Download anycut from the market and create a shortcut to an activity called "testing". This will open the same menu as *#*#4336#*#* only this one does not reset on reboot.
Took me some time to figure this one out.
Sent from my GT-P1000 using XDA App
can any one tell me how exactly to put google nexus s in diag mode because i need to flash it to boost mobile. thank you
Once you get into diag mode using *#*#4636#*#* just change it to wcdma only and instead of going back go to home directly. that's what i did. it sticks even after reboot.
Joeykrim and nemith have dialer codes working in cdma cyanogen nightly. The code is *#*#8778#*#*
Or *#*#3282#*#*
Uncle Jimmy says hello
U will do the *#*#8778#*#* to connect to qpst. From qpst you can get your MSL. Write that down.
Uncle Jimmy says hello
how to get MSL
Don't need QPST. If rooted, just launch terminal, type getprop and look for the line that says "[ril.MSL]: [xxxxxx]" -- that's your MSL. Could also do it with adb shell getprop from your computer.
kashah said:
Don't need QPST. If rooted, just launch terminal, type getprop and look for the line that says "[ril.MSL]: [xxxxxx]" -- that's your MSL. Could also do it with adb shell getprop from your computer.
Click to expand...
Click to collapse
Sweet. Way easier than configuring qpst
Uncle Jimmy says hello
I'm not responsible for what might happen on your phone if you choose to dial any of these!
These are the codes that work on the standard phone dialler app on the Orange San Francisco, but I'm pretty sure they'll be almost identical on other models that we collectively know as "ZTE Blade". Known small differences (in texts) are down to whether the firmware expects to be running on an OLED or TFT display, and whether you've deleted seemingly unused apps like ChiperTest.apk, fcctest.apk and QcNvTest.apk. Most are prefixed with "*983*", which is "*ZTE*" in phone letters -- I've added a mnemonic for the other part where I think it's obvious (feel free to suggest better ones!).
"Automatic Inspection" runs through the basic tests automatically (usually you need press a button to move on to the next bit -- don't get thrown by any blank colour test screens!). There are a number of interesting items for developers, with hardware info and other goodies. If any of the descriptions don't make the function obvious then it's either poorly written or I don't know exactly what it does (I'll happily update this if others can explain better).
If the code has been recognised by the dialler then it will react immediately when you enter the final "#". If nothing happens when you've done that, don't press Dial!
Edit: on the ROMs based on the Japanese 2.2 you need to put the phone into "Engineering Mode" first, by dialling *ZTE*OPENEM# (*983*673636#) -- this action will be confirmed by a quick pop-up. To close this mode, dial *ZTE*CLOSEEM# (*983*2567336#) -- this then prompts whether you want to do a Factory Reset, which you do not have to do (you can simply Back away from this screen).
Dial Mnemonic Operation
*983*0# Menu (20:Battery/OLED/Back Light/Vibrator/Ringer/LED/Key/OLED off/SD/BT address/Radio Info/Memory/TouchPaint Test/Audio Loop/FM/Camera/GPS Test/IMEI/IMSI)
*983*3640*01# IMSI
*983*25# Battery Info[/COLOR]
*983*31# OLED Test
*983*26# Backlight Test
*983*850# Radio Test 0
*983*86# Vibrator & LED Test
*983*84# Ringer Test
*983*07*01# Headset Test
*983*07*02# Key Test
*983*3470# LCD Test
*983*81# SD Test
*983*890# -
*983*26*# Radio Test 1
*#06# IMEI
*983*27274# CRASH Reboot
*#08# Test Flag [Note: requires QcNvTest.apk in /system/app]
*#09***# BT Test
*983*1275# _ASK Dev Info
*983*7# Menu (4:Version/IMEI/IMSI/BT address)
*983*3640# DOH+ Phone Info (inc ping test, radio on/off)
*983*636# MEM Memory Test
*983*28# BT Emode BT Test
*983*477# GPS GPS Test
*983*21# Audio Loop Test
*983*70# Automatic Inspection
*#18# LED Test
*#19# TouchPaint Test
*983*36# FM FM Test
*983*57# Factory Reset
*983*473# Camera
*#23# Video Camera
*983*10# Delete (Touchscreeen) Calibration File
*#25# FM Test
*983*2726# SIM Contacts Op 1
*983*37# SIM Contacts Op 2
*983*6726# SIM Contacts Op 3
*983*154# "test" Menu (12:Self-starting/Software
Version/Hardware Version/PSN/Test Flag/[Completed]/Board Serial/Bluetooth
Address/SMS security/SMS Registration Status/Flash Type/PRL Version/Serial Configuration)
*983*07# Menu (9LED/Ringer/Vibrator/Key Test/Audio Loop/Headset Test/FM/Camera/SD)
*983*5182# Dev Info
*983*7469# SHOW Automatic Inspection
*#26***# Sensor Test
*983*7936# QXDM Save Qxdm in log system
*987*0# Menu (4roduce Information[->"test" Menu]/Automatic Inspection/Factory data reset/Battery information)
*#27***# Compass Test
*983*87274# USBSI USB Switch Test
*983*06# BT Test
*983*564738# LOGSET LOG Set (inc sys_rw)
*983*93# FCC Test [Note: requires fcctest.apk in /system/app]
*983*2377# CFQP Call Forwarding Query with PowerOn
*983*24474636# CHIPINFO Chiper Test (chip info) [Note: requires
ChiperTest.apk in /system/app]
*983*29873283# AXUPDATE Touchscreen Updater
*983*73564# SDLOG SD Log
Note: the above are for the standard ROM (well, apps) running 2.1. The current Froyo ROM (with standard dialler, etc.) does not have the Touchscreen Updater, but adds:
Dial Operation
*987*123456# DM Test
IN modaco
Hello, what code shude I use to know if my SF is TFT or Amoled?
Regards!
Check the build number in Settings>About Phone. AMOLED ends in 05, LCD ends in 08. IIRC all white SF models are 08 and most grey are 05 (unless its a newer unit which will likely be 08).
Thank´s man.
Mine is 01. What that means?
Looking at the screen characteristics it seems like LCD.
Thanks man. great post
Really nice. Works on Boost Mobile Warp Sync N9515.
Would you happen to have a code that forces prompt for unlock? (Changing sim cards doesn't trigger anything)
same here... up for this....
No Boost Mobile ZTE Warp Sync N9515 Unlock Screen
chinnyss said:
same here... up for this....
Click to expand...
Click to collapse
I think unlocking the Boost Mobile is a lost cause. I've tried several other sims and the only codes I've found to show the unlock menu don't work:
1) Alright then please remove the SIM card and try this code ###825*09#,
2) Got the prompt for code? Please enter the code you received,
3) Failed above, try *983*8284# to access the Unlock Menu,
4) Failed above, finally try *983*865625# to access the Unlock Menu.
zte warp elite n9518 rooted but still i can't use MSL reader or alogcat it says in root checker verify root congrats and after rebooting i got to root again please help just need to get SPC and or MSL code
You the MAN! THA KS.
kelvinpacquette said:
zte warp elite n9518 rooted but still i can't use MSL reader or alogcat it says in root checker verify root congrats and after rebooting i got to root again please help just need to get SPC and or MSL code
Click to expand...
Click to collapse
Can u tell me rhat what do i need to enable usb debigging or adb mode ?? I have to connect my zte z982 device to miracle sodtware, but unable to connect because frp lock.
I cant enable usb debugfing
techeligible3322 said:
Can u tell me rhat what do i need to enable usb debigging or adb mode ?? I have to connect my zte z982 device to miracle sodtware, but unable to connect because frp lock.
I cant enable usb debugfing
Click to expand...
Click to collapse
Edit: on the ROMs based on the Japanese 2.2 you need to put the phone into "Engineering Mode" first, by dialling *ZTE*OPENEM# (*983*673636#) -- this action will be confirmed by a quick pop-up. To close this mode, dial *ZTE*CLOSEEM# (*983*2567336#) -- this then prompts whether you want to do a Factory Reset, which you do not have to do (you can simply Back away from this screen).
Dialing the first set of numbers made it possible for me to turn on abd....
Sent from my SM-G550T using Tapatalk
Alright
paigesdavis1996 said:
Edit: on the ROMs based on the Japanese 2.2 you need to put the phone into "Engineering Mode" first, by dialling *ZTE*OPENEM# (*983*673636#) -- this action will be confirmed by a quick pop-up. To close this mode, dial *ZTE*CLOSEEM# (*983*2567336#) -- this then prompts whether you want to do a Factory Reset, which you do not have to do (you can simply Back away from this screen).
Dialing the first set of numbers made it possible for me to turn on abd....
Sent from my SM-G550T using Tapatalk
Click to expand...
Click to collapse
Thank you for your reply
How did you enter / enable adb? I have a 971 and the 2nd code from your site doesn't work, I am able to enable eng. mode
I also tried the connect to computer in control panel and that doesn't do anything either.
Frp locked
Trick
techeligible3322 said:
Thank you for your reply
Click to expand...
Click to collapse
This worked for me and I have the ZTE z blade max thank you
Has this been proven to root the phone yet ? Please leave feedback .
Good News
#Starlord37# said:
This worked for me and I have the ZTE z blade max thank you
Click to expand...
Click to collapse
That's very good to know you are welcome
I haven't had a chance to try it fully yet as I have been trying to root my girlfriends Moto e4 with magisk which I will probably have done by the end of the night and then I plan to tackle my z982 will keep you posted though
sprint evo 4g
freash evo rom 4.3.3
os 2.3.3
kernal.2.6.35.10-g13578ee
software
4.54.651.1
pri
2.15_003
prl
45722
model pc36100
i set everything to 7025555555 and [email protected]
did all the steps i found online anderify it shows in settinng the mms stuff apn v
rooted with the revolution thing unlocked with cdma workshop
beleive im done now just need to get cricket service and go back in and change the numbers mdn nai and stuff right
CAUSE RIGHT NOW WHEN I DIAL 611 IT DOESNT SAY CRICKET IT SAYS WELCOME TO NATIONWIDE ROAMING AND I CAN MAKE A COLLECT CALL OR US A PIN ??? I TRYED TO COLLECT CALL A FRIEND LOL AND IT SHOWED AS 7025555555 LOL .. SO DID I DO THIS ALL RIGHT OR SHOULD I GET WELCOME TO CRICKET EVEN THO NO CRICKET INFO OR MDN MIN NAI OR STUFF IS FOR A REAL ACCOUNT ?
You should have posted in Q&A. This is for dev's.
i got it had to ##786# or whatever to clear it
setup proper apn load apn xml
setup evo freash rom
spl unlock
set spl as 000000
had to setup nam data imsi cricket logins and more
hybrid cricket prl
and yes 5 stores said no 2 places said it couldnt work here
finnaly someone would take the esn then had to wait and fiddle around with phone eventually got the welcome to cricke tbut the *228 dont work
had to ##000000# change mdn min whatever
then ##data# edit mode and enter 6 0's again edit what you need
verify apn by going into txt mgr app and setting then settings normal u can change em here but u can when u ##data#
anyways
all n all no one helped me
i spent 3 hours trying to figure out why ater i unlocked the spl and tryed to reset it the spl wouldnt take
kept saying enter 6 digit code in order to read the spl lol cought in a loop i guess this would help others
cdma workshop click the terminal tab enter this into command box 41 74 64 77 61 6F 70 then click send!!
Now click the security tab and read SPC the current SPC should come up.
NOW send it to the phone to unlock it then enter 000000 click write to phone!!
DONE!!! UR EVO IS UNLOCKED
also if its not written as all zeros i think this flashing wont work
and it was 15$ to get cricket to do a phone change they say blabla mms net not garr to work haha
i got txt mms net 3g gps everything but actual 4g but so what gave to friend cause it was a project ... was his cricket account haha
Hi Guys,
i have a problem with my Note 4. I attached a screenshot and you can see that there is no Preferred Network Mode option in it. I also try the code (*#*#4636#*#*) for hidden menu to change it but nothing happens coz when i changed the setting from GSM/LTE/Auto to GSM/CDMA/LTE/Auto and go back from the menu it will be revert automatically.
Can someone fixed it or have any solution???
Is there any one to help ????
I believe it requires a build prop or csc code edit that requires root for the settings menu but the service menu method should work as long as you do it correctly...and I say correctly not assuming your doing it wrong but to encinuate that there is a certain way you have to enter the keys..... Google it and you should be able to find a video