I recently dropped my 8525 hard enough to throw battery out of phone. I reinserted battery and started phone. Though I lucked out as everything seemed to work until I couldn't make a call. During boot I get "no GSM" instead of a battery version. I have done a hard reset, but it didn't help. I going to try to install a new ROM and if needed try to flash a new radio.
Anybody else have this problem? I am afraid it is a hardware malfunction in the radio.
If I cannot get this to work (I have already bought a new phone) I will be more then willing to donate (just pay for shipping) the phone to anyone who would like to work on it or test things on it. I have one half good battery and one good battery as well. Like I said everything seems to work but the actual phone. Let me know if you want it.
meh, that is not good news my friend, hope you get it fixed!
if it is a no go however, i wouldn't mind taking it off your hands
best of luck,
tbae2
Try to reflash original or stock rom. Go with the carrier rom you are supposed to have. It might work as there have been reports to indicate this.
Hope it works for you.
Cheers...
I have recently gone through similar problems, there are numerous things that can cause the NO GSM error on post. So here is the complete solution:
1. Some hard drops can jostle the antenna connection on the board, (a dodgy way of testing if this is the issue is to give the phone a shake and a few soft resets, the NO GSM error will sometimes disappear and state your radio version). There are numerous service manuals that describe how to disassemble and reassemble your handset (read the forums). It sounds scary at first, but so does not having a working phone (be sure you are out of warranty first). You will want to get some electronic circuit board cleaner and give the area around the golden clip on the top left (back facing up) a good spray (while you are at it, why not clean out some dust scroll button detritus). Then dry and reassemble, taking care to force the antenna all the way into the clip.
2. If step one really scares you or you are still in warranty, skip straight to here. A program called mtty (i use vers 1.42 , check the forums) can be used to interrogate the board logic from the bootloader, there are numerous tasks that can be used to clear registers and check gates for errors (for lack of a better word), the wiki has a great entry on all these.
3. A reflash of the radio and maybe even the os isn't a bad idea either... although remember that the latest radio may not be the best for your area/network (READ THE FORUM on this too)
Let us know how you go with it all, and good luck
if you need any further assistance PM me.
ultramag69 said:
Try to reflash original or stock rom. Go with the carrier rom you are supposed to have. It might work as there have been reports to indicate this.
Hope it works for you.
Cheers...
Click to expand...
Click to collapse
This was my idea last night as well. Froze on bootloader. I tried to also Install new radio but also a no-go. I am now downloading a new ROM without radio to see if I can get something other then bootloader. I will keep posted.
I can take the phone apart if I need to, I will make it a last resort. I am not afraid to though as I already have a new phone.
Seeing as I still cannot figure out how to make a ROM to contribute (vista and lack of programing skills) This would be a way I can assist If it would be more useful to someone here not dismantled I would like to look into it.
Update:
The radio hardware must be bad. I cannot flash a new radio or any rom with a radio. Schap's EM6 is working fine. I am going to look into discodergenson 's suggestion of taking the phone apart.
Schematic Diagram
Hi, I have a HTC 8525, with the same problem, doesnt start phone module.. anyway, in my phone, the sim card is not detected. Anybody have schematic diagram for this model? Or any other htc model, for reference.
I think this problem can be caused by dry solder in the driver of sim card, must identify it.
Thanks in advanced
(Sorry for my bad english)
datachaos said:
Hi, I have a HTC 8525, with the same problem, doesnt start phone module.. anyway, in my phone, the sim card is not detected. Anybody have schematic diagram for this model? Or any other htc model, for reference.
I think this problem can be caused by dry solder in the driver of sim card, must identify it.
Thanks in advanced
(Sorry for my bad english)
Click to expand...
Click to collapse
I don't think a bad SIM card connection is a problem. Without a SIM card the phone still needs a radio connection to make 911 calls.
also obviously I only have a t8 and higher, not a t6 which is needed to take phone apart. I will update when I get phone apart.
Related
Hi all,
I have a 8125 (Wizard) that I bought used with a broken LCD - I replaced the LCD with hopes of having a functional phone, but I'm not quite there...
It WAS working as a nice little PDA for a while, with the newest Cingular ROM (2.25 I believe). HOwever, I received absolutely NO signal on the radio - the little animation just constantly went like it was forever searching.
So, in my newfound expertise in flashing HTC devices, I decided to flash this to a different ROM. First, I tried the one they call Button 1.05. No bones - it'd drop connection before even going to the tri-color.
Next, I tried the SlimEdition 2.2b of WM6 (I wanted to put WM6 on it anyway, and with this old of a phone, I'm keeping away from excessive gadgets). Same deal as the Button 1.05.
On to the Faria WM6 I found in another forum. This one didn't even find my phone.
Before suggesting I try doing the flashes more than 1 time, I did.. I've been trying to flash this thing for over a month...
Additionally (and probably part of the problem), when I connect the phone to my mini-USB (no, not HTC OEM) it establishes connection about 1/3 of the time....the rest of the time I get a "USB Device not Recognized" warning from XP - I then disconnect it and reconnect it until AS4.5 sees it.
Most recently, I tried putting the Button 1.05 on again, and actually made progress...sorta...
Once I got the RUU running, I actually got it to progress to 2% before the RUU declared a connection failure. Stuck in the RUU screen, I tried all the ROM's I have on this thing, and none get past 2%.
So, NOW, I have an 8125 that's stuck in the RUU screen. I dont know what I can try next, or what might be the problem - however, if anyone knows or has spare parts they're willing to donate to science (I can afford to pay the shipping - that's about it) then I would be most grateful. My initial thoughts are bad USB port or mainboard, but I haven't a clue where to get them.
Alternatively, if I dont hear from anyone soon with good news, I will be offereing for sale 1 hardly used LCD/Digitizer combo for what I paid for it. (approx $45 USD).
Summary (long post, eh?):
1> Can I get out of the tri-color RUU screen, or did it getting to 2% and then dying effectively brick this phone?
2> Anyone have suggestions on what to replace to prevent AS4.5 (or even Windows) from misdetecting the phone when connected via USB?
3> Anyone have parts for above-mentioned repairs/replacements? I'd be most grateful....
TIA!
- M
Follow up - next day (yes, next day)....
Apparently, the Forum Gods were watching over me as I spewed about my flashing issues......
I tried flashing it one more time, using the Slim v2 WM6 ROM....wouldn't ya know, the sunnovabatch worked....
Dunno why or what I did differently, but I dont want anyone pounding their heads trying to find an answer for this....
(I'll still take any donor phones, though...this one is 'better', but still not 'great')
Thanks for lookin!
- M
thats good to hear. say, how hard you think it would be to replace a usb port connector? mine is broken
collwatt said:
thats good to hear. say, how hard you think it would be to replace a usb port connector? mine is broken
Click to expand...
Click to collapse
Well, I've never replaced one myself, but it looks like it's just a few solder joints....
Can anyone confirm this? I dont want to mislead you by saying it's easy, in case it just looks easy, and really isn't.....
Also, I think I saw a thread elsewhere where someone had a bunch of the USB connectors that (s)he was selling....search here first - I'm pretty sure it'll be a better deal than you'll find on fleabay....
GL!!!
- M
I know this is a strange request but I need to deliver my phone for repair because of HW issues and since it seems way to hard to recreate the original operator image from the dump, I thought that if I could get the phone into a situation where there is no bootloader then that should be enough.
Any ideas?
Thanx,
Eran
jocool said:
I know this is a strange request but I need to deliver my phone for repair because of HW issues and since it seems way to hard to recreate the original operator image from the dump, I thought that if I could get the phone into a situation where there is no bootloader then that should be enough.
Any ideas?
Thanx,
Eran
Click to expand...
Click to collapse
Allow mw to suggest the following: Why don't you try to set it on fire?
Cheers.
I would say a bunch of big magnets should do the trick.
Kevlar-Source said:
Allow mw to suggest the following: Why don't you try to set it on fire?
Cheers.
Click to expand...
Click to collapse
Wish I could but if I break it physically need to pay a fine
simple answer:
HTC doesn't take "the phone was burned" under warranty...
So instead of giving nonsense remarks, you could have said nothing instead.
Of course this is cheating, in a way, but since there are HW issues and HTC doesn't repair unless it's the original ROM on it...
Jocool: One method would be to disconnect during a ROM installation, thou i'm not sur if you can't still get it right after that.
You'd probably have to get it to the original bootloader which shouldn't be too hard and then interrupt it during a Radio flash.
Flash a radio and pull the cable about half way through...i think that should do it!
ai6908 said:
Flash a radio and pull the cable about half way through...i think that should do it!
Click to expand...
Click to collapse
I tried this with a full ROM and unfortunately still gets to the boot loader. Will try this later.
Thanx
Eran
actually, i thought HTC dont cover software issues?
and if YOU damage the bootloader in the update process is that not your responsibility? as i'm pretty sure the RUU states somewhere that you update at your risk?
if i were you, just do something to fubber up the mainboard, best thing i suggest is to put something into the micro sd card slot which will basically insulate the pins such that it doesnt make contact with the memory card, that way you can get the thing changed like i did with my old charmer!
Piezoelectric gas lighter...
I haven't said this, I have not been there...
duke_stix said:
actually, i thought HTC dont cover software issues?
and if YOU damage the bootloader in the update process is that not your responsibility? as i'm pretty sure the RUU states somewhere that you update at your risk?
if i were you, just do something to fubber up the mainboard, best thing i suggest is to put something into the micro sd card slot which will basically insulate the pins such that it doesnt make contact with the memory card, that way you can get the thing changed like i did with my old charmer!
Click to expand...
Click to collapse
I need to get this to the operator for fixing. It is actually easy enough to return to an original HTC ROM but that won't work for me
brick your phone???
4 months ago I sent my device for repairing, but they sent it back after 3 months with a note that: "the device can not be repaired any more becasue the Flashbaustein (this is the name in German and I couldn't find the english word) is kaputt"
of course I can assure you they even didn't try to switch on the device in these 3 months... after a long discussion with the T-Mobile agent, I took my device home and tried to re-flash a new ROM on it and everything went as it should be.
be careful with the risks you might cause to yourself
i once did it with my htc wizard ... though i forgot how already ... but I think it did it through the sd card... not sure if it's possible with hermes though since I didn't try that ...
but anyway, i think I modified the first few bytes in the 512 header of the rom with random characters and copied into the sd card to flash my wizard.
Tada, killed the bootloader
I hope that you can do that with the hermes ... I did see a wiki on how to flash your hermes through your sd.
Hope this helps
Burn Baby Burn
Hi
Try this, i assure you that will do the trick.
Connect a USB Cableto the HTC, get a 20V AC adapter, connect a wire to the Positive and one to the negative on the AC adapter connector, connect the negative to the outside of the usb cable, and, use the positive in every other contacts, wen you see SMOKE, STOP.
I'am preaty shure that they wont get to the BootLoader
New Idea
I have an idea...
1. Get an anvil
2. Get a sledgehammer
3. Place your Hermes on top of the anvil
4. Drop the sledgehammer on it
5. Pick up the pieces
6. Glue them together
7. Polish it with a fine cloth
8. Wrap it in a fancy paper
9. Send it to wherever you were sending it in the first place
Cheers.
compumad said:
Hi
Try this, i assure you that will do the trick.
Connect a USB Cableto the HTC, get a 20V AC adapter, connect a wire to the Positive and one to the negative on the AC adapter connector, connect the negative to the outside of the usb cable, and, use the positive in every other contacts, wen you see SMOKE, STOP.
I'am preaty shure that they wont get to the BootLoader
Click to expand...
Click to collapse
I believe it would be more effective with a high voltage... Just imagine pluging it directly into a high voltage power line... It would be better than fireworks
the best way is to cause an electrical fault. just connect a 12V car battery to the battery terminals of your phone. just be careful as you may kill yourself due to the high current flwoing out of the battery regardless even though its 12v.
Thanx to all that gave me ideas some practical and some not
I was able to convince my provider to replace my phone without turning it on so problem solved
I fried my blackberry by just putting it in the microwave for 15 seconds, pop and bam dead
If you wanna brick your phone, just go into clockwork recovery and format your sdcard and so a whole system wipe. That's what I did then took it to verizon and got a new Droid x.
i have a htc wizard with window mobile 6.1 and it won't find a signal it just says searching all the time. also the connection icon is on beside the signal icon but the connection icon has a "x" below it. PLEASE HELP! my sim card is fine it works in other phones. i don't know if it a software or a problem with the antenna .
ipl 2.26
spl 2.26
gsm 2.25.11
os 6.1.0.0
Help Please!!
I have read for hours hours on this forum and can't find a solution PLEASE HELP ME. I love my new wizard and want it to work right.
It sounds like you have an unlocked G3 (or else you wouldn't have WM6.1).
Before I flashed it, though, I would recommend just opening the battery, removing the back cover (it's not too hard), and checking the antenna connections to make sure they're still contacting the foil antenna on the inside of the back cover. Shut the phone completely off (press and hold power button). Open, and lift the foil carefully with a hobby knife and flatten it a bit, before laying it back down. Verify the two spring-loaded contacts are able to compress and extend fully without any coaxing from you. If they stick, flex them a few times to see if you can loosen them up. If they still stick, you could try using Isopropyl Alcohol to clean them, but you must wait until it is completely dry before reassembly. Reassemble and power up.
If it still doesn't pick up a signal, you might consider flashing GSM to either 2.19 or 2.69. Most Wizard owners end up on one or the other. A few find success with other versions, but they are exceptions.
Collection of Radios inside (ALL Radio ROMS) - xda-developers
I tried you solution but same problem . I've tried flashing a new radio but i have vista and the rom updater just crashes, i've read and tried a lot of the fixes the forum has told me to with no luck.
This may not be that helpful, but make sure that the SIM card is completely inserted. At first I didn't realize that it had to slide under the small metal things, so mine didn't work. =P
that was the first thing i tried. i even tried someone else sim cause i thoght it might of been my sim card nope not it.
I would recommend you flash the original ROM back into your phone and see if you get any signal that way.
Have you tried a hard reset? If your hardware checks out, then this might work. Also, did you or any previous owner ever have failed unlock attempts?
Hi
Ok so my phone was working fine on a custom ROM when suddenly yesterday an exclamation appeared next to the phone signal and stopped from receiving/making calls and texts. I thought it had just crashed but after soft and hard resets and changing to a few others sims I just can't get my phone signal back.
Really strange as everything was working fine. I now have trouble flashing custom ROMs and am struggling to run a stock ROM because I'm on a mac.
It's driving me crazy as my phone is now useless.
Any ideas guys?
thanks
Quick update
I've managed to get the Leo Lite ROM running and everything is good except that damn exclamation mark next to the phone to phone, which means I can't get the phone working.
Anyone know know why this is???
Have you tried the sim in a different phone?
could just be a simple issue
And I know it a simple thing............but have you got flight mode on?
johnerz said:
Have you tried the sim in a different phone?
could just be a simple issue
And I know it a simple thing............but have you got flight mode on?
Click to expand...
Click to collapse
Thanks for the reply John.
Yeah currently having to use the sim in an ancient motorola and it works fine, tested with calls and texts. Also tried turning on and off flight mode but still that bloody exclamation mark stays.
That sounds like its been blocked. Theres a network there it just isn't letting it connect. Did you buy it second hand? or off ebay?
samsamuel said:
That sounds like its been blocked. Theres a network there it just isn't letting it connect. Did you buy it second hand? or off ebay?
Click to expand...
Click to collapse
Hey Sam
Do you know what, I did buy it second hand, from a reputable store in town.
However this raises more questions than answers;
1. Why would it be blocked after several weeks of normal use.
2. Doesn't some sort of message need to be displayed stating the handset has been blocked.
Does anyone know if this is what happens when a HTC HD2 is blocked? i.e. the exclamation being shown all the time.
I presume a handset is blocked for security measures like theft. I will take it back to the shop tomorrow, they will have all the details of the person who sold it to them.
However is there no way this can happen from flashing custom ROMs? Even though that doesn't really make sense cause I had a ROM that was working fine and this happened when I was out and about.
It could be a bad rom, but it certainly wouldn't be in every rom.
I think id try going back to the stock rom, radio and spl (i.e an sd card flash, do you now if it has a provider locked rom?) and see if it is still there. If it still won't work, then it's definately either hardware or network.
The reason it could have taken weeks is, , seller trades in phone for cash, waits a little while, thinks 'i know'..., reports the phone lost/stolen to claim on insurance, insurance won't pay out without the imei being blocked.
samsamuel said:
It could be a bad rom, but it certainly wouldn't be in every rom.
I think id try going back to the stock rom, radio and spl (i.e an sd card flash, do you now if it has a provider locked rom?) and see if it is still there. If it still won't work, then it's definately either hardware or network.
The reason it could have taken weeks is, , seller trades in phone for cash, waits a little while, thinks 'i know'..., reports the phone lost/stolen to claim on insurance, insurance won't pay out without the imei being blocked.
Click to expand...
Click to collapse
Well I've tried flashing at least 6 custom ROMs, all show the exclamation mark.
The phone was sold to me as being unlocked to all networks, however I never tried with anything other than a o2 sim.
Now going back to the original ROM has its own problems. First off i'm quite new at this so sorry for sounding silly. How on earth do i go about finding out what the original stock rom, radio and spl is?
When I have these I can't easily go back as I don't have a pc, using a mac. I would have to use the sd card way but I can't find an official signed .nbh file.
I have a brand new T-Mo US HD2 with similar issue (out of the box). It's like the radio will not initialize. Did hard resets, tried to force it finding a carrier, etc, and it just will not turn on the radio.
I did find out that there is a likely issue with my SIM slot. If I attempt to remove my SIM card (which works fine in other phones) it is almost unremoveable and feels jammed in. However, once removed, I get connectivity via wifi and touch response is great.
If I insert a SIM card, it takes a LOT of pressure to reinsert it (yes, inserting it in the correct orientation), and the phone cannot connect turn on the phone's radio. Also, I get random phone.exe and credential.exe error message (plus the phone becomes very slow.
Don't know if you have any of these other symptoms, but the lack of connectivity sounds similar.
Supposed to get a replacement HD2 today, and we'll see.
I had the same problem too. I got unlocked code from tmoile and everything working fine for a month. It was working great after upgrade the latest rom 3.14 from tmobile download site (i got the message from them to upgrade), until i went out off country last month then the phone could not turn the phone's radio on. It kept at airplane mode. I been try to flash back and forth all the tmobile .50 stock rom and still having the problem.
Does any one know the issue to fix it? TIA
Looks like a hardware fault. You need to open case and check bottom two brass hinges are in working order and correctly hinged to make contact with antenna which is on the rear case at the bottom.
Follow the guide of opening s HD2 on YouTube there is a factory guide to dismantling the HD2.
xlr8me said:
Looks like a hardware fault. You need to open case and check bottom two brass hinges are in working order and correctly hinged to make contact with antenna which is on the rear case at the bottom.
Follow the guide of opening s HD2 on YouTube there is a factory guide to dismantling the HD2.
Click to expand...
Click to collapse
Thanks for reply xlr8me. I just check the two brass hinges at the right side of usb connector. It looks fine to me. The other thing i didn't mention on the above post I was flash the dft_leo_nand android after tried all the stock rom from tmobile and the android said "no sim card", i also checked and cleaned the sim slot. Do you think any thing else to cause that problem?
One more thing without the sim or sd card the about phone show up all info of phone: imei, serial..... But with sim card in it just blank when i read the about phone hardware info. Thanks again
Did you try simcard from another carrier?
cecobald said:
Did you try simcard from another carrier?
Click to expand...
Click to collapse
Yes I did tried the sim from the carrier of the asia country i was traveling to last month, that why i call tmobile to get the unlock code before i go. When i was there and inserted their carrier's sim and it won't work, even when i get back to U.S. I been tried either tmobile or at&t sim too. The phone radio won't turn on. The rest is working ok except those above error messages "A problem has occurred with device.exe" and "Credential.exe".
Do you think i can reflash with WWE rom .50 radio instead of tmobile's official rom?
Thanks
htcphonelover,
You will have to reset the phone back to default rom from htc website. You may also need to reformat sd card but the radio should still work regardless of whether the sd card is in or out.
My only concluding thoughts are that if the above fails to work then try a different sim card and still no good then probably something with the motherboard on HD2.
Good luck and update us with any new info..
Hi all, I normally don't like to post questions because i feel like the answer is somewhere online, and i almost always find it. Apparently this is one of those times i can't. Bear with me as i wanna make sure i dont leave anything out.
My problem is simply that my HD2 will not find any access points when i turn on my wifi. This started happening to me with a previous HD2 i had about a month ago for no aparent reason. I had not changed or flashed anything on my phone around the time the problem happened. I figured i would ignore the problem because i had 3g anyways but then that HD2s touch screen failed so thats why i ended up sending it in for a warranty replacement.
Now i hoped that since i had a new HD2 that the problem would be gone, i mean how could it be possible that the problem would appear on a brand new phone. So i went about doing my usual. Installed 2.08.HSPL, followed by MAGLDR, followed by MIUIAndroid.com rom, same setup i had before the problem began. I made sure the first thing i did was turn on WiFi on first boot of the phone. To my suprise, No access points found. I know it is not my router as i have connected every other device im my house to my router, including other androids and windows phones. I thought maybe its a MAGLDR/Android issue. Flashed back to WinMobile 6.5 and still no acess points. Tried every radio available and still no access points.
Bottom line is im really confused how this can be with a brand new phone. Im pretty sure its a software issue but im out of ideas.
SO please if anyone can help. Please :'-(.
Just found out this morning that it can find my access point, but only if i literally lay it on top of my router. if i go more than maybe a foot away from it then nothing.
It sounds like a hardware issue. I read about these things having issues with a connection to the antennae that can be solved by taking apart the phone and cleaning some leads.
joshnchen said:
It sounds like a hardware issue. I read about these things having issues with a connection to the antennae that can be solved by taking apart the phone and cleaning some leads.
Click to expand...
Click to collapse
Sounds strange that such a new phone would have a hardware issue already. at this point though, im willing to try anything. how/where exactly would i clean/find these leads?
Check this: forum.xda-developers.com/showthread.php?t=834199 and this: forum.xda-developers.com/showthread.php?t=1190180, but be aware that opening your phone might void your waranty. Good luck
is that the only rom you have flashed? and was it nand, or sd etc...??
make sure because it could be a simple error in software as well..
something you can try and report back before opening up the phone
b12rtc said:
Check this: forum.xda-developers.com/showthread.php?t=834199 and this: forum.xda-developers.com/showthread.php?t=1190180, but be aware that opening your phone might void your waranty. Good luck
Click to expand...
Click to collapse
thanks. will take a look at those.
tecle2595 said:
is that the only rom you have flashed? and was it nand, or sd etc...??
make sure because it could be a simple error in software as well..
something you can try and report back before opening up the phone
Click to expand...
Click to collapse
I first got the problem while it was still stock. then i flashed miuiandroid.com's rom with MAGLDR and still. then i went to tytungs ICS Beta4 roms and still. now im back to the miuiandroid rom. so it doesnt seem to be a rom issue.
also all the roms were nand
gotenksnath said:
Just found out this morning that it can find my access point, but only if i literally lay it on top of my router. if i go more than maybe a foot away from it then nothing.
Click to expand...
Click to collapse
Hi my Friend,
your black Wifi Coaxial-Cable inside your HD2 is unpluged and not correct Connected. I had this three times at three different EU-HD2 Devices, too ( the Distance for a working WIFI Signal was 1 Feet. Normal, without Antenna ;-)). Regular the Connector at the PCM at the upper Corner fall of...
If you Still have Warrenty you have to bring this Phone to a Service. If not, you have to fix this little Problem by yourself ( you need 2 Minutes to do that ). Be Carefully when you Bring the whole HD2 inside your Backcover. You have to Tape the Vol-Rocker with a little Sticky-Tape. So this Plastic can´t fall off during the reassembling and is not to Deep to kill the Vol. Buttons...
The Opening is easy. You need only a Guitar-Plectron and t Torx-Screwdriver. Here you find Pictures:
http://mperlitsch.hintergrundbild.com/htc_hd2.htm
Here a Picture from you Sick-Zone:
http://mperlitsch.hintergrundbild.com/htc_hd2/hd2_23.jpg
Where the RED ARROW is, you see One Wifi-Connector and i bet a Sex-Pack good German Beer, this one is your Problem. Put this Connector Back and everything works fine...
Best Regards,
Micha
P.S. Sorry for my poor english !
Perlitschke said:
Hi my Friend,
your black Wifi Coaxial-Cable inside your HD2 is unpluged and not correct Connected. I had this three times at three different EU-HD2 Devices, too ( the Distance for a working WIFI Signal was 1 Feet. Normal, without Antenna ;-)). Regular the Connector at the PCM at the upper Corner fall of...
If you Still have Warrenty you have to bring this Phone to a Service. If not, you have to fix this little Problem by yourself ( you need 2 Minutes to do that ). Be Carefully when you Bring the whole HD2 inside your Backcover. You have to Tape the Vol-Rocker with a little Sticky-Tape. So this Plastic can´t fall off during the reassembling and is not to Deep to kill the Vol. Buttons...
The Opening is easy. You need only a Guitar-Plectron and t Torx-Screwdriver. Here you find Pictures:
http://mperlitsch.hintergrundbild.com/htc_hd2.htm
Here a Picture from you Sick-Zone:
http://mperlitsch.hintergrundbild.com/htc_hd2/hd2_23.jpg
Where the RED ARROW is, you see One Wifi-Connector and i bet a Sex-Pack good German Beer, this one is your Problem. Put this Connector Back and everything works fine...
Best Regards,
Micha
P.S. Sorry for my poor english !
Click to expand...
Click to collapse
Thanks so much to you and everyone who helped me out. Im going to see how much longer my warranty is because the only reason i would really send it back is if the touch screen fails AGAIN (happened twice already) but that wont happen for at least a year. So if warranty is gonna expire before then ill fix myself. again thank you to everyone.