I got a Bluetrek G2 Bluetooth headset, and i paired it up and when i presss the button i work but after that it not working anymore no matter how many time i press the button
Any advise?
when using VC from MS via BT the Audiogateway stays open.
You have to close it (by pressing the BT button once) before you can give an new command (by pressing the BT button once again)
Related
Has anyone any idea on how I can adjust the time required to hold the headset connect button in order to activate the voice command? Currently I need to hold this for far to long in order to activate it.
Maybe there's something in the manual, but I can't even anwer calls with that button. I think it's supposed to be short press to answer calls, and long press for voice command. Still not figured it out.
That's odd, I press the button for a brief moment , and voice-command is activated.....BT headset btw, but it works like a charm...
The handsfree wired headset that came with the Dopod is the one that takes quite a few seconds of holding to respond. I imagine that a bluetooth headset would work differentially as the time is probably controlled by the device itself rather than the HTC 3600.
I have a BT-850 bluetooth headset, and everything works perfectly but every time I turn the headset off for charging and then back on, I have to go to bluetooth settings, delete the partnership, press the button on the headset for the Wizard to find it, enter the 0000 password, tick on Hands free and tap Finish. It is a PAIN IN THE ARSE TO DO THIS EVERYTIME!!
If I turn the Wizard off completely and reboot, the headset still works. The problem happens when I turn the headset off and back on only.
Is there a way around this?
TIA
hmmm.... i also have the 850, and aside from having to use BTaudio to force it to be a stereo headset, i havent encountered that problem.
have u tried just opening it up and pressing the universal button on the headset?? that usually instantly connects me to my phone.
Hmm are we talking about the same headset? Mine is not stereo!
Attached is a picture of it.
Marton said:
Hmm are we talking about the same headset? Mine is not stereo!
Attached is a picture of it.
Click to expand...
Click to collapse
BTAudio pumps system sound (including music) via bluetooth headset profile, as opposed to A2DP to a stereo headset.
So when you turn on your headset, can you press the call-answer button to try and initiate the connection? That is what I do with my Itech S38.
I think my headset is defective. After reassociating, it works perfectly when I press the call/end button on it. The problem is only when I turn it off and back on. I hate to go driving and have to reassociate it when I forgot to do it before jumping into the car...
Marton said:
I think my headset is defective. After reassociating, it works perfectly when I press the call/end button on it. The problem is only when I turn it off and back on. I hate to go driving and have to reassociate it when I forgot to do it before jumping into the car...
Click to expand...
Click to collapse
When you turn your headset off, and back on, then press the call/end button, does it reassociate?
Solved!!!
By a casuality I turned the headset on and kept the call button pressed. It started to blink the red and blue lights rapidly. I then deleted the association on the Wizard and started a search for BT devices. After some seconds it found the headset but with a headset icon (before, every time it detected the headset, it had an arrow or something like that) I then added it and now it works perfectly. When I turn it off and back on, I press the call button and it reassociates alone and opens voice dial. AMAZING!!!!
Thanks for the help,
Marton
I got my Touch today and I purchased and installed Voice Command 1.6. After the install I rebooted my phone and pressed the button on my headset to bring up MSVC but nothing comes up.
Any idea what I am doing wrong?
Strange... does the button work? I'm not having any problems with mine. I had to turn off confirmation with my BT and VC 1.6 combination because the final confirmation wasn't completing... besides that everything works fine with my Jawbone - try another headset?
In the past all i did was press the button once. It appears the touch (or MSVC 1.6) requires you to press and hold the button.
So now it is working. YAY!
What BT headset did you get it to work with ?
On Leo ( with original last rom) i installed VoiceSpeed Dial , but I can not find a way to start this sw when I press the buttom "call" on my headset BT,
the same problem on my Sony car stereo with Bluetooth,when I press the dedicated button, call the last call number. Any solution for this? Tanks in advange.
Try..... press button on headset, hold it down and wait for two bips in headset.
steveianson said:
Try..... press button on headset, hold it down and wait for two bips in headset.
Click to expand...
Click to collapse
thanks friend, just like it does not work, if i press button & hold it on headset BT or Car Stereo, no run VoiceSpeed Dail but call the last call number, ( both devices functioned good with all Nokia phone) but if i hold the button "calling" on the Leo VoiceSpeed Dial run and emits "beep" correctly.
Where can I find information on how to handsfree initiate a call from a bluetooth headset? My understanding is that Android 2.2 Froyo supports this. I have my Plantronics 975 headset synced and working, but can't get voice dial to initiate. Pressing the button on the headset just makes a beep, but doesn't do anything on the phone. Pressing the button twice redials the last number, but it did that on my old G1 with Android 1.6.
Is anyone using a Plantronics 975 with a G2? Does voice dialing work for you?
Thanks,
Tauren
yowzator said:
Pressing the button on the headset just makes a beep, but doesn't do anything on the phone.
Click to expand...
Click to collapse
No idea about the plantronics. With my headset (Sony DR-BT22), pressing the call button on the headset starts the voice dial app (audio through the headset) and a long-press performs a redial.
I figured it out and feel stupid now. But just in case someone else is having trouble, here's the answer...
* Hold down the main button for 2 seconds and voice dial starts (see http://bit.ly/bO0Gvo)
* Double press the main button and redial starts
* If bluetooth is not connected, single press the main button to connect.
* Not sure what a single press does if the connection is already established.
I never tried a long press because a really long press shuts the headset off. I didn't even think that there might be a "short long press" and a "long long press".
On my Moto H17 BT headset, it seems a single press on the button initiates the voice dialer on my G2, and a "short long press" redials.