How to downgrade RSU or swith from 900/1900 to 900/1800 - MDA, XDA, 1010 Software Upgrading

Hi all,
Thanks to this thread http://forum.xda-developers.com/viewtopic.php?p=39630#39630 and especially remarks from hb88xx, I successfully managed to recover from my own mistakes (that many people have done as well apparently).
Here is the story:
* I bought my O2 xda from Telstra in Australia where the band is 900/1800. It is a PW10A1 device.
* I then cooked a rom with Yorch's kitchen and as many others, didn't read enough posts before doing so and opted for the infamous EXE method as I had successfully upgraded once before from O2 using this method.
* As my bootloader is 5.17 and my cooked rom was based upon T-Mobile, I was stuck: impossible to downgrade the bootloader because of TMO checks (the wallaby patch doen't work) and impossible to up/downgrade using the SD card method because of the bootloader version.
* Still, I could use my device but my WM2003 was very buggy.
* Out of hope, I decided to upgrade to another TMO rom, but this time an official one (4.01.16) as I read it was quite stable.
* That was the BIG mistake as I also did the RSU upgrade and I ended up with a 900/1900 device, having the 4.21 RSU.
* I tried many of the tips I read from this forum, but none of them worked and I had to buy a cheap cellphone to use my SIM card on it and keep my xda as a pda.
Basically, what you need to do is the following:
* Using the attached file or the official TMO upgrade, extract and copy the files into the \Windows directory of the xda.
* Detach it from the craddle and run the EXE on it.
* It says things in german (performing upgrade) and then a final status (whatever "erfolreich", ie successful). Click OK and finally, reboot the device.
* You now have a 3.23.11 RSU.
Once again, thanks a lot to all participants to this forum and especially hb88xx.
And thanks also for the remark below
Regards,
Bob.

Hey mate ...
It's great that you have learned this lesson, but now you may cause troubles to some unexperienced users by posting this file with this name
Simply, what you have posted is the typical RSU upgrade 4 files you should find in ANY RSU exe file, but because you posted this file with the name RSU_Fix, I 'm afraid some one will just use it with a B device thinking it will solve his problem and endup with a dead RSU.
So, plz remove this file or rename it RSU_3_23.zip or so

BobMorane said:
Hi all,
Thanks to this thread http://forum.xda-developers.com/viewtopic.php?p=39630#39630 and especially remarks from hb88xx, I successfully managed to recover from my own mistakes (that many people have done as well apparently).
.....
Bob.
Click to expand...
Click to collapse
Hi BobMorane.
I am having the same problem as yours, upgraded to WM2003 and can't go back to ppc2002.
Sounds like You have reverted your xda rom to ppc2002, didn't you?
Don't quite understand those that listed in your post. Could you explain a little more?
Thanks.
Raymond
XDA1 bootloader v5.17

Hi bob,
I'm a little confused - I understand RSU 4.21 is for 900/1800. It is the RSU that o2asia currently distributes.
My XDA is a PW10A1 and currently has RSU4.21 (from o2asia), Wallaby 5.17 (no idea where it came from... am guessing o2asia as well) and T-mobile WM2003 4.01.16 ENG (.EXE cooked from Lumpistefans)
As a result, I'm stuck as well. However, I can still use my phone on GSM900/1800; as long as I avoid settings-phone-band; all is well; but if I do wander into that, a reset to the bootloader-calander-gsm900/1800 solves the problem (albit temporary...)
Anyway, I'm meeting up with a friend to borrow a SD card+reader over this weekend or the next, so that I can change the ROM (get out of theT-mobile WM2003 rut). Am a little concerned about what you wrote however:
BobMorane said:
* As my bootloader is 5.17 and my cooked rom was based upon T-Mobile, I was stuck: impossible to downgrade the bootloader because of TMO checks (the wallaby patch doen't work) and impossible to up/downgrade using the SD card method because of the bootloader version.
Click to expand...
Click to collapse
Could you please eleborate more on how the wallaby patch didn't work? How did downgrading the RSU to 3.23.11 help? Are you able to replace your T-mobile ROM or Wallaby 5.17 following that? Or are you still stuck, but at least the phone works on GSM900/1800?
More information please?

Hi,
Some anwers below.
RaymondB :
Actually, I didn't revert to PPC202 and I still enjoy the 2003 features, but I managed to get rid of a 900/1900 issue.
xdagirl :
My problem was slightly different as I did not have the RSU4.21 for asian devices. My aim with the post was more to explain how to get out of the original T-Mobile rom lock-in (I did not use a cooked one because of my 5.17 wallaby). I assume you can do it as well with the asian RSU4.21. If you have it, I can try it and let you know.
As for the 5.17 wallaby issue, I was stuck in the midst of 2 issues : the 5.17 doesn't let you access the SD card method and you need first to downgrade it to 5.15. The patch to do this can't be used if you have installed a T-Mobile rom as it blocks the connection. I couldn't get around this and that's the reason I upgraded to the offical TMO rom.

BobMorane said:
Hi,
Some anwers below.
RaymondB :
Actually, I didn't revert to PPC202 and I still enjoy the 2003 features, but I managed to get rid of a 900/1900 issue.
......
Click to expand...
Click to collapse
Thanks for your reply, Bob.
So you are still with WM2003. Is this the new official one or the buggy one that you've had earlier. If its the new one, how did you do the flashing?
Did you downgrade the bootloader to v5.15?
I really wish to go back to ppc2002, as the current one seems to be quite unstable. At times, it reset itself, especially when some changes was made to some particular today plugin. It also turn on itself, which eat away the precious battery power. Also, the phone setting function and the band switching utilities will hard reset the xda.
Sorry for so much bugging. Hope your could help.
Thanks and cheers.
Raymond
XDA1 bootloader v5.17

Related

Which is a recent / suitable ROM and Radio upgrade for QTEK

Hello folks,
QTEK 1010 bought from Dubai
Model PW10A1
ROM version 3.16.52 ENG
ROM Date 03/10/03
Radio version 3.19.01
Protocol version 32S54
My questions: -
For me, which is a suitable upgrade...
From www.myxda.com:-
ROM version 3.20.06
Radio version 4.21
OR
From www.carrierdevices.com.au:-
CE Upgrade File : RUU_CEv3.18.04wwe_Qtek_SHIP.exe
Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe]
Thanks
Faisal
Re: Which is a recent / suitable ROM and Radio upgrade for Q
faisal said:
Hello folks,
QTEK 1010 bought from Dubai
Model PW10A1
ROM version 3.16.52 ENG
ROM Date 03/10/03
Radio version 3.19.01
Protocol version 32S54
My questions: -
For me, which is a suitable upgrade...
From www.myxda.com:-
ROM version 3.20.06
Radio version 4.21
OR
From www.carrierdevices.com.au:-
CE Upgrade File : RUU_CEv3.18.04wwe_Qtek_SHIP.exe
Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe]
Thanks
Faisal
Click to expand...
Click to collapse
You may use any ROM Updgrade, you may even want to cook your own ROM, but please do not think of performing a radio stack upgrade if your present radio is working well and giving you a trouble free service.
Hi guys,
I 'm in same situation but with higher versions, and can hardly wait to get a new 2003 ROM.
I can't just play with my XDA as I use it all the time for work and it's pretty stable so far. I just also can't tell that the ROM is 'totally' separate from the RUU in WM2003.
So the question is: is there any one here who has gone through a 2003 upgrade for Qtek 1010 to tell us his thoughts after the upgrade ?
I read a lot about the stability of 4.00.16 ENG, but all been written was for O2 R4.21 or T-Mobile R6.xx. Did any one in this region (Mid East) with R 3.2x went into this upgrade ? and what is the current status ?
Thanx all ....
Latest ...
I tried upgrading to 4.00.11 ENG from the kitchen ... no matter how many trys it just restarts and gives the same error message "Can't open USB/com port ..." ...
Do I miss anything ??
more update ...
Tried to cook the new ROM as .nb1 file and used Xdatools from the kitchen to flash my device .... same result :? :evil:
Is it possible that there is a ROM protection on my XDA ??? :shock:
Biso007 said:
more update ...
Tried to cook the new ROM as .nb1 file and used Xdatools from the kitchen to flash my device .... same result :? :evil:
Is it possible that there is a ROM protection on my XDA ??? :shock:
Click to expand...
Click to collapse
Hi Biso007,
Look at the IDIOTS GUIDE at:
http://www.xda-developers.com/forum/viewtopic.php?t=3171
and follow the instructions thoroughly one by one and you can't go wrong, it did work for me, I was in the same situation.
Samohile - Thanks. It is good advice to not mess with the radio if you can help it.
My only problem is that my device periodically shuts off. Then pressing the power button soft boots it. I cant tell for sure but it seems that this happens after an incoming or missed call. It seems that other friends using ROM 3.18.04 and Radio 3.25.01 (like our friend biso007 here) seem to have very stable systems.
I can try upgrading the ROM only and see what happens but the information at www.carrierdevices.com seems to imply that both ought to be upgraded at the same time. I notice it is an Australian site. Does that matter? Also, the version of the radio upgrade is a bit confusing, at least from its name. (Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe] ). I wonder what this RSUv1.15 translates into since the name of the exe file for the ROM is nicely descriptive of the version (3.18.04).
Any advice in this would be very welcome..
Well i am using WM2003 4.00.11 and its working fine for me no problem i cooked in the kitchen you just need to read arround this great forum for a whgile on topics such as upgrades and ROM to know exactly what you are dealing with and then you will able to upgrade smoothly.
:wink:
Hi ARZLEB
I read lots and lots about upgrade lessons but none of them worked for me .... I got an advice to use SD card with bootloader as it's the only working way. Now I wonder why the EXE method was created!!
I see that u got the 4.00.11 working. Did u upgrade it using EXE or SD card. Any help would be so appreciated ... thnx
Well i used the EXE methode the file i cooked in the Kitchen but i didnt change the version i left as 3 at the bottom of the page it works fine i upgraded from 3.XX to 4.XX then i downgraded from 4.00.11 to 4.00.05 then upgraded again all using EXE format so far working great.
i will be honest with you i know about the SD methode very well but never tried it so u have to make more search on this issue.
If you need anything more plz message me anytime and i will be more then whilling to help you step by step...
faisal said:
Samohile - Thanks. It is good advice to not mess with the radio if you can help it.
My only problem is that my device periodically shuts off. Then pressing the power button soft boots it. I cant tell for sure but it seems that this happens after an incoming or missed call. It seems that other friends using ROM 3.18.04 and Radio 3.25.01 (like our friend biso007 here) seem to have very stable systems.
I can try upgrading the ROM only and see what happens but the information at www.carrierdevices.com seems to imply that both ought to be upgraded at the same time. I notice it is an Australian site. Does that matter? Also, the version of the radio upgrade is a bit confusing, at least from its name. (Radio Upgrade File : RSUv1.15_(GPRS_T32500_ENG).exe] ). I wonder what this RSUv1.15 translates into since the name of the exe file for the ROM is nicely descriptive of the version (3.18.04).
Any advice in this would be very welcome..
Click to expand...
Click to collapse
Faisal sorry for very late reply.
I have flashed my Qtek (bought in Abu Dhabi) with several versions of roms cooked in kitchens (Jeff's and Stefans's), but I have finally settled with ATT release wm2003 Siemens SX56 upgrade. It comes with most of the bugs fixed (except multiple reset bug) and is quite stable. I almost never have to reset it. You can flash the ROM only by SD card method though. You can try it. It's always a good idea to flash using SD card method. USB method using ProgramA is not very safe. I guess the network in Pakistan is compatible with the one in the UAE, so you can safely use it, if you don't mess up with the Radio Stack. My Radio is 3.23.01 and I have no problems with that.

Special Edition WM2003 Rom?

ok, i have installed the special edition rom for my xda1 and its a definate improvement over the original rom..
but i noticed that the window mobile 2003 upgrade is available from o2 and wondered whether it was significantly better than the special edition?
of course, if there was a xda-developers special edition rom based on wm2003 that would be the best solution... :?
Nas
There are many WM 2003 ROMs and most of them works quite fine ... try the kitchen at www.yorch.net or http://lumpistefan.dyndns.org/
nasman said:
but i noticed that the window mobile 2003 upgrade is available from o2 and wondered whether it was significantly better than the special edition?
Click to expand...
Click to collapse
Where is the WM2003 upgrade from O2??????
Give me alink to download please...
Stefan
I didnt know there was one, anybody else seen it?
nope i cant see it.
my bad
soz, not from o2, just the ones from other providers that are floating about.
Re: my bad
nasman said:
soz, not from o2, just the ones from other providers that are floating about.
Click to expand...
Click to collapse
Just do it, upgrade it! I upgraded my Siemens SX56 with AT&T to 2003 and than cooked the rom from Yorch to unlock. By the way, it is a very good rom, thanks Yorch.
I did it with SD cards one of my XDA's, it worked perfect and quick: saved 2003 rom on one card, cooked Yorche's on another. The saving and installation was done through the bootloader as discribed in the proceedures in frequently asked questions section. The extracting and saving of Yorche's rom was done through OSImageTool in XDAtools into an SD card inserted in a USB card reader/writer (Inland 9 in 1 card Reader/Writer, $10 at Micro Center). The battery was fully charged on my SX56 and the flashing of rom's back and forth was done without the XDA being pluged to power unit. I tested the unlocking with a T-Mobile card, it recognised it, I made some phone calls with no problems, kept Yorch cooked rom for two days to get to know it and then flashed it back with my SD saved 2003 rom in my friends apartment just to show off how easy it is to flash the rom. it worked very well (it took about 5 minutes).
The 2nd SX56 was done all through ActiveSync with the XDA and card reader/writer pluged in and all synchronised (allscreen savers, power savers etc on PC and XDA OFF and battery charged). This XDA still had the original 2002 rom. The unlocking went very smooth. I did a full back up of the rom with ActiveSync. Since the cooked rom is PW10A1 and mine was PW10B1 I needed to get back my original rom to the XDA. The restore didn't work because it is a different partnership. So I flashed it back with my SD saved 2003 rom in a card reader/writer and OSImadeTool through ActiveSync. Everything was fine all the way to hard reset. I waited a minuteor so and did a hard reset and nothing happened, did it couple of times, nothing. It would not restart. I pressed the power botton and it went to bootloader mode. I did soft reset and the unit goes blank, dead. So I inserted the SD card with my 2003 rom into the XDA's memory slot and did the the bootloader mode, it took it, I flashed it. And now I have my 2nd SX56 with 2003 rom and the old radio stack ulocked working like a champ. I tasted with T-Mobile card and it works instantly, no configurations needed. Now I have to do a complete upgrade.
After all I like the new 2003 better but with some of the programs from Yorch Kitchen rom, which I installed and they work fine.
You, ladies and gentlemen, at XDA-Developers are the greatest thing that happened to the mobile devices community. I honor you and thank you. And Peter Poelman, you are the wizard, thank you.
John
can you guys show me how to cook to ROM or and link to download the file upgrade from wm2003 to 2003. Thank a lot . I'm using O2 XDA 2002
tommy_kiss79 said:
can you guys show me how to cook to ROM or and link to download the file upgrade from wm2003 to 2003. Thank a lot . I'm using O2 XDA 2002
Click to expand...
Click to collapse
Look here for the answers:
http://wiki.xda-developers.com/wiki/FAQ
and here to cook the rom:
www.yorch.net
check what you want or don't want and click Build ROM now, after it is done click Download. Before you build and download choose which file you want, exe or nb1. What ever you do backup your original rom preferably and safer to an SD card either through OSImageTools in XDATools and ActiveSync or the mode and the SD card pluged into your XDA
bootloader, and read the forum in details...
The new Mobile 2003 you can get at any of the provider or manufacturer of XDA's: www.T-Mobile.com, www.ATTwireless.com, www.My-Siemens.com, Microsoft has a list of manufacturers that have upgrades - www.microsoft.com/windowsmobile/resources/
Make sure you use the right one for PW10A1 or PW10B1 what ever your device Model No. is...
Good luck, John
saracen said:
The new Mobile 2003 you can get at any of the provider or manufacturer of XDA's: www.T-Mobile.com, www.ATTwireless.com, www.My-Siemens.com, Microsoft has a list of manufacturers that have upgrades - www.microsoft.com/windowsmobile/resources/
Make sure you use the right one for PW10A1 or PW10B1 what ever your device Model No. is...
Click to expand...
Click to collapse
John (and any others out there),
I hope that I'm not asking something here that is covered in some faq on this board and I think I've read them all, but...
I see mention of a lot of versions. 4.00.21, 4.00.01, A30.05, A30.09 etc...
Is there someone that can tell us new guys a little more about these? IE, what is it exactly, 2003, 2002, beta, final, alpha?
I recently bought a Wallaby, and want very much to use the MS Voice Command. Therefore, I have a definate need for a 2003 rom. I have read and reread the forums here and have a good handle on how to flash my rom, but I'm so confused as to what the best (read most reliable) rom to install, as well what radio version would work with the given rom choice. I'm not necessarily asking for a recommendation, but perhaps a nudge in the write direction.
Sorry to dump on you in particular, nothing personal either mind you! It's just that I'd love to read a FAQ for the different versions and what might be expected from them I guess. (I hope like heck I'm making sense here!)
Thanks!
Larry
Hello,
Actually, the only difference between ROM versions is bug fixing with newer versions, but the only significant factor is whether it's PPC 2002 or WM 2003 ROM.
For upgrading, I may recommend TMO 4.01.00 (my personal preference) or A30.09 (with a minor sound issue). If you need to unlock your device you must start with PPC2002 3.17 ROM first then select any WM2003 later.
There is no connection between the ROM and RSU. However, the RSU is the most sensitive part in the XDA. If you have a functioning RSU ... do NOT touch it!!
Last, get a SD card and take a backup ... it's safer and you can use the SD to upgrade as well.
Good luck ...
This is to Larry,
All these replies take you through the right directions. I have two Siemens SX56 devices with AT&T Wireless, both PW10B1, Pocket PC2002 (Ver. 3.0.12039), ROM Ver. A.20.17 ENG, RADIO Ver. A.20.10, 32MB Rom.
1st one I upgraded the day AT&T and Siemens released the Mobile 2003 free upgrade. As much as people complained, cursed and were distroying there SX56 devices ( what I read on AT&T forums) I never had any problems, and as a matter of fact the more I used the device the better it became. I played with it for about two weeks and then I decided to unlock it. So I placed my SD card into the SX56, started the bootloader, downloaded the original 2003 Rom image, soft reset the device. I cooked the Special Edition Rom based on 3.17.03 O2 ROM in Yorch Kitchen, I built the nb1 file, I downloaded, extracted with WinZip, put it on another SD card, put the card in my SX56 device, started the bootloader, flashed it, did a hard reset. It didn't ask me if I wanted to unlock it but the XDAunlock program was there, I taped it, it asked me if I want to unlock, I did. I checked it with a T-Mobile sim card, made a phone call with no problem (I tested with the same card before and after, before asked me for the pin number and after it logged in to T-Mobile network). I used it with the Special Edition Rom for about a week to see which programs I liked and wanted to install on my device after I flash back to saved Mobile 2003 Rom. I flashed it back with the 2003 Rom image. I was on the road, away from power supply, my pc, usb ports etc. Just the unit with its battery charged up, the SD card and the bootloader. It took 5 minutes.
My 2nd SX56 device I did before the 2003 upgrade, the original 2002 still there, with ActiveSync, OSImageTool in XDATools, SD cards, card reader/writer and nb1 file. This time I overlooked the saving of the original 2002 Rom and it went directly into the flashing with the Special Edition Rom cooked in Yorch Kitchen. I unlocked it, tested with T-Mobile sim card and flashed it back with the the Mobile 2003 Rom image saved from my 1st SX56 device. It didn't want to wake up after the hard reset. It kept going to the bootloader mode. So I inserted the SD card into the SX56, started the bootloader , flashed it back again with Mobile 2003 Rom, did a hard reset. It worked. Now I have my 2nd SX56 with new mobile 2003 Rom but old, the original Radio Stack from Pocket PC 2002. It works fine. The working is like the Upgraded 2003 device. Maybe with the older radio Stack is more stable on the signal, and I don't know for sure because I did not tested, only what I read and the people having problems. My preference is a total upgrade, the Rom and the Radio Stack, I noticed that the audio quality is better with the total upgrade, specialy when on the speaker phone during a phone call.
What ever you do save the settings and the Rom images and you do the right PW10A1 or PW10B1 (the Special Edition Rom is PW10A1). Make sure all the screen savers, power savers, sleep modes etc. are turned off on both the PC and the XDA device.
Good luck, John
saracen said:
What ever you do save the settings and the Rom images and you do the right PW10A1 or PW10B1 (the Special Edition Rom is PW10A1). Make sure all the screen savers, power savers, sleep modes etc. are turned off on both the PC and the XDA device.
Good luck, John
Click to expand...
Click to collapse
Thanks, guys!
I kind of knew that the differences were a matter of bug fixes, what I wasn't sure of is which is 2003 or 2002. I'm going to keep reading here of course. This is a fantastic site to be sure!
So, bottom line is I guess I'm just going to pick a couple of them and flash them and play with them so which works the best.
Many thanks again guys! Larry
Larry,
Yes, exactly. I forgot to say that my new rom is an AT&T- Siemens: ROM Ver. A.30.09 ENG, Radio Stack A.33.02. The previous Rom version had a band switch (900 for Europe or 1900 for Americas) in the Settings and under Phone but now with the new it has an auto configuration which I like better. I can always search the network manually. By accident I found that if you set it to manual and don't have a network specified or any signal strength showing as long as the phone is turned ON, I can still get on Internet.
Good luck, John
One final ?
Guys
Is there ANY version of the W2003 ROM that comes with the Wmodem (or similar) application ?
I first came to xda-developers when I was trying to use my Qtek as a modem....thereafter we saw the O2 and Qtek PPC (2002) upgrades that brought in the Wmodem utility.
That seems to have disappeared off the priority list for most people these days, though.
Cheers
Sands
Sandyind said:
That seems to have disappeared off the priority list for most people these days, though
Click to expand...
Click to collapse
IMHO, the new PCs/laptops with either built-in WiFi or WLAN functions or with equivalent PCMCIA cards, or even with SIM module inside, made it out of the wishlist
Re: One final ?
sandyind said:
Guys
Is there ANY version of the W2003 ROM that comes with the Wmodem (or similar) application ?
Click to expand...
Click to collapse
The German Version 4.00.33 from t-mobile comes with the wmodem application
HTH
Stefan
Stefan,
Is there an English version of Mobile 2003 with wireless modem for PW10B1 XDA?
Thanks, John
Can't receive USA Cingular signal 850mhz- Help Anyone?
I've posted on some other forums but no-one seems to have an answer. Can an unlocked AT&T SX56 be adjusted to work on the Cingular 850mhz system?
Help!!
Doc

Want to uninstall WM2003 and go back to O2 original ROM

Hi!
Installed T-Mobile WM2003 from the ROM kitchen.......... Network very weak and the phone has become very slow. Now I want to move back to O2 original ROM (WM2002).
When I try to install the ROM I get an error message :
"ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host. error getting connectiontype"
and the 02 ROM installer cannot communicate with my XDA.
Can someone please help me get back the original 02 ROM, with sim unlocked???
Really need some help here. :?:
I loved my phone as it was and I was stupid to experiment with it !!
regards ,
Diki
If you used the kitchen to cook your ROM then it shouldn't have any impact on the RSU part. Plz give more details on your RSU version, your network MHz and what types of problems you have ?
BTW, did you upgrade to 4.01.00 or 4.01.16 ?
To get back to PPC2002, you can use the SD method
if you upgraded to the 4.01.16 I had this problem too.
you can't use the rom.exe method via the cradle if you've put this tmobile rom on your XDA, you have to use the SD flash method.
I upgraded it to 4.01.16
Radio version installed is 4.21.00
PROBLEMS:
a. The XDA has become very slow (I have a lot of free space on the XDA)
b. Network signals are weak.
Going back to 2002
I received from a friend a pre-release version of t-mobile ppc2003 a few months ago. He put it on my phone via a sd flash. T-mobile has just released (for free) on their website a final release of ppc 2003 and the one I am using is somewhat unstable at times. Does anyone happen to have t-mobile ppc2002 so that I can upgrade. Thanks.
Diki said:
PROBLEMS:
a. The XDA has become very slow (I have a lot of free space on the XDA)
b. Network signals are weak.
Click to expand...
Click to collapse
a. there is a bug in WM2003 and there is a tiny program that should be placed in the \windows\startup directory to solve it. The program is called Clear_Notify.exe ... simple search and you will find it.
If not, then it's a Radio problem that impacts the ROM part. Few hard resets may solve it.
b. if you mean the indicator on the window tray, forget about it ... the point is the ability of making/receiving calls. If you face real problems, I think it's the 4.21 RSU, but be extreamly careful ... upgrading the RSU is very risky especially with this RSU 4.21 on your device!!!!!!.
Good luck
tellan said:
if you upgraded to the 4.01.16 I had this problem too.
you can't use the rom.exe method via the cradle if you've put this tmobile rom on your XDA, you have to use the SD flash method.
Click to expand...
Click to collapse
1. Can you please send me the steps for installing the O2 OS on a SD card?
2. and once it is installed and working, can I just go ahead and delete all the folder (windows program files etc) from the phone memory?
What are the risks involved in writing ROM to SD Card?
I have no idea of this. Can you please help me?
Hi Diki,
Did you get a soution to your problem yet? I elaborate on the same problem.
Thanks for your answer
Norbert
I have the same problem and I still don't know what to do. Please elaborate if you can.
:roll: I have this problem too. If someone find the selution,PLS send me a Email: [email protected].
THX!
:roll: I have this problem too. If someone find the selution,PLS send me a Email: [email protected].
THX!

Unlock CID of Prophet SPL 2.xx

The programmers of www.pdamobiz.com in Thailand have successfully unlocked the CID for HTC Prophet SPL 2.xx. More information is available at:
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437&PN=1&TPN=1
Wow, that's a very good news indeed
Now I just have to find an Orange France M600 rom to test if it work
I'll test with the Jamin one also...
If someone can upload the M600 french rom, i would be very grateful, thanks!!
Does anyone succefully download the unlock program? the connexion is very very slow on their server (I'm downloading in Bytes/sec :shock: instead MBytes)...
If yes, it would be nice to upload it on the ftp server, thanks!!
cedrick said:
Does anyone succefully download the unlock program? the connexion is very very slow on their server (I'm downloading in Bytes/sec :shock: instead MBytes)...
If yes, it would be nice to upload it on the ftp server, thanks!!
Click to expand...
Click to collapse
Thanks to someone that uploaded the file. It's here:
ftp://xda:[email protected]/Prophet/pdamobiz.com_downgrade_and_unlockcid.rar
Actually it was there ftp://xda:[email protected]/Uploads/Prophet/pdamobiz.com_downgrade_and_unlockcid.rar :wink:
Not sure what happenned to the Prophet folder on the ftp, I though there were more files inside yesterday :roll:
Thanks a lot anyway
Im probably missing something here, but isnt it enough just using Machinagod great No ID crack when upgrading a ROM?
Just copy it to the nbf files and run it, works like a charm.
So, what is the difference with this application?
I don't know the app you're talking about, but we're talking here about downgrading, not upgrading a rom...
Moreover, does your application remove CID on prophet with SPL 2.xx ?
well, should have tested that before speaking...
doesn't work for me, once run the downgrading program, I soft reset but the device stay blocked on splah and I can't connect back to active sync to run the unlock program... too bad, that seemed to be a good way to downgrade rom :?
...great work! just used it on my qtek s200 that i've accidently flashed with the latest o2 germany rom without cid-unlocking before. now i can really put any rom on it
thanks and cheers, lutz
did i work? what happen when you soft reset after running the downgrade tool?
thx !
everything worked as it should, no idea why it didn't work for you...
cheers, lutz
Ok thanks,
BTW, ignore my PM didn't though you'd reply so fast :wink:
do a hardreset and pray that you get it connected to active sync, buddy...
as said above, it worked exactly as they've said it will. i have no idea what went wrong for you so my help is poor...
cheers, lutz
Actually I tried various time... I'm on the last Dopod rom, i started as said, then when I reboot, the device is stuck on dopod splash screen...
So I have to go into the boot loader in order to reflash the dopod rom I have... at least I can do that and keep my S200 working
Maybe this doesn't work with the last Dopod rom, but at least it worked for others
we need a Thai to Eng. translation to understand the problem
Unfortunately my device can not continue with second step. After I softreset it; the device freezes. Neither hardresetting, nor putting in bootloader and continuing with hard or soft reset helps. I reflashed the latest Dopod ROM and continued to use it.
I can not read Thai language but from the original discussion (not english but in Thai language) I see that a number of people are having the same problem. I also understand that the suggested solution works for some others.
The english version is not a full translation of the original discussion; translation of a lot of answers are missing.
We need the help of our Thai friends to understand what is going on.
I guess that it works on certain rom version, if you've the dopod one like I had, then it confirm that this method is useless with the last dopod rom...
But we have confirmation it work with other roms... maybe it's not really working on SPL 2... roms :?
I took a look on the Thai version, now it's clear that it doesn't work on the last dopod rom SPL 2.15 !!!!!!!
cedrick - Sorry you have failed to CID-unlock your Prophet and congratulations to lutzh that has succeeded.
From the Thai version of this utility, many people could unlock their devices but some did fail to do that. Not sure only the SPL 2.15 or not that couldn't be unlocked but at least 2 people claimed that their devices are SPL 2.15.
The website programmers are still trying to investigate and find the solution to help people who failed. Please hang on. Good luck!
@cedrick:
Yeah my SPL is 2.15
@Khuanchai:
Thank you for information. Hope to hear better news.
Cheers.
No problems about the failure, that's already nice to see tools like that that can help a bunch of people.
Now I hope it will also work on the dopod rom as I really liked it and I would like to update my prophet with this rom. But I prefer to wait until there's a way to get back to whatever rom :wink:

Softbank X01HT questions..

Hi all, I've received a really deal good for a Softbank X01HT. I was wondering if like the other Hermes, the only difference in this unit is the button layout and OS language. If I upgrade to any other Hermes ROM will it function like a regular Hermes? Thank you for replies.
Yes, basically it will work as long as you have your device SIM / CID unlocked.
I say 'basically' because of I found some incompatibilities on my HERMES (a AT&T 8525). It does not accept the German T-Mobile ROM and also not the ORANGE CH. Other than that I did not get any problems.
You might wanna read the HERMES UPGRADE sections in the WIKI first? That should get you started!
Thanks for your quick reply Junner, I appreciate it
Another question has arisen; the unit I'm getting is in english language, so presumably a different ROM has been flashed to it. Does this mean that the phone is now SIM unlocked? Or does Softbank have english versions of their phones as well? Mine will be a white one, not sure when it was manufactured.
Hello,
If its already in English then chances are that it was flashed with a WM5 English ROM. If you're lucky, then the phone could be SIM unlocked, but ROMs can be flashed if the phone is Super CIDed... The white edition models were made after Softbank issued an update for all their phones..
My bet is that your phone is Super CIDed.. but heck, you'll never know these days, you could get lucky and have it SIM unlocked!
Softbank do have english versions of their phones, but the X01HT is just one of their exceptions...
I'm using the Black X01HT flashed with a WM6 Rom.. and its great! You won't be dissapointed!
Hey nesy, thanks for the heads up. I've got the phone in my hands, it works great. It's been flashed with some version of WM6, not sure which flavour. And it's goot IPL 1.01 and SPL 1.40.Olipro. My guess is that this was unlocked by imei-check, and it must be SuperCID too. Will be sure once I probe the internals with mtty. My only concern now is whether if I'm able to upgrade the radio, since I've read reports of some people being unable to flash over radio 1.14.something.
Is there really a downside to being stuck at radio 1.14 found in the Softbank phones? If so, what are they? Improved reception? stability?
well my softbank phone was at radio 1.14, I was able to upgrade it without any problems to 1.50.... you dont really have to upgrade, but I found that any version above 1.2 had better battery life...
I have a X01 that I just bought with a Chinese ROM (I am currently in China) and it was already unlocked. I had no problems putting an English Rom on. Be sure to change the keyboard layout to Japanese, I had mine set to Chinese for a while and 2 buttons were different.
Question: What are the advantages to upgrading the radio? Can anyone provide a link that explains how to upgrade / advantages to upgrading?
neshyd said:
well my softbank phone was at radio 1.14, I was able to upgrade it without any problems to 1.50.... you dont really have to upgrade, but I found that any version above 1.2 had better battery life...
Click to expand...
Click to collapse
really? how were you able to upgrade? i thought it was impossible to upgrade the radio on a softbank
pasan said:
really? how were you able to upgrade? i thought it was impossible to upgrade the radio on a softbank
Click to expand...
Click to collapse
I also just upgraded to 1.41... I use the method that temporarily Super-Cids it. But dont ask me how that works because I have no idea.
Could you link me or PM me with how you did that? All the wikis stated that I can't upgrade the radio to anything else because of the bootloader. And I tried it too, the radio ROM gets flashed, but upon reboot, the same old version number is shown. Thanks in advance.
courtlandre said:
I have a X01 that I just bought with a Chinese ROM (I am currently in China) and it was already unlocked. I had no problems putting an English Rom on. Be sure to change the keyboard layout to Japanese, I had mine set to Chinese for a while and 2 buttons were different.
Question: What are the advantages to upgrading the radio? Can anyone provide a link that explains how to upgrade / advantages to upgrading?
Click to expand...
Click to collapse
Hey dude, there are many advantages to upgrading the radio.. especially if you're still at 1.14... For instance, in Japan and China, the networks are UMTS here... although radio 1.14 gives satisfactory reception, higher versions improve this as well as enabling HSDPA (higher 3G download speeds) . The battery management is improved, and currently I'm using radio version 1.48 (1.50 was a battery sucker when using WM6)
you should read this before upgrading the radio:
http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
and read under 'Upgrading and Cooking'
and to flash the radio you HAVE to install Hard SPL.. this is a modified bootloader for the hermes.. and also it prevents it from bricking when you upgrade the ROM or radio.
Get it and the guide here:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
Finally,
Go here:http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
and choose what Extracted Radio ROM that you want to install. Download it, run the EXE file and run through the program wizard.
After the radio has been uploaded to your device, it should reboot and you'll hopefully see some improvement!
Also another thing, be sure to search the forums, there are many great guides here, much better than my attempt
Hopefully that answers your question Pasan, you could try to do the method mentioned above by courtlandre which is to temporarily SuperCID it, but I didn't use that, i ended up unlocking my phone and SuperCID'ed it... so that my upgrade process will always be stress-free
pasan said:
Could you link me or PM me with how you did that? All the wikis stated that I can't upgrade the radio to anything else because of the bootloader. And I tried it too, the radio ROM gets flashed, but upon reboot, the same old version number is shown. Thanks in advance.
Click to expand...
Click to collapse
I am using SPL 1.10 I think (wiki or a sticky will have instructions on how to install this).
Then I just downloaded the radio rom and installed it. Worked fine with no problems.
Thanks neshyd, I once tried upgrading to HardSPL 2.30 but it didn't work, upon reboot it was still on 1.40.olipro. This phone was unlocked by the imei-check people and they may have done something to prevent future SPL upgrades.
courtlandre said:
I also just upgraded to 1.41... I use the method that temporarily Super-Cids it. But dont ask me how that works because I have no idea.
Click to expand...
Click to collapse
is this SSPL?
I guess you guys have older Softbanks, mine is a post April 07 model which does not allow the radio to be upgraded

Categories

Resources